Table of Contents
Advertisement
Image
> DNR: If the image is not clear due to noise, this option can
reduce the noise of the image.
> Saturation: Set the intensity of the color.
> Sharpness: The degree to which the boundary of the two
portions is clearly distinguished. If you set the sharpness
value to higher, the image outline becomes sharp. If you set
to lower value, the image outline becomes dim.
> Privacy Mask
-
Add: Click the [Add] button.
1. When you click on the preview screen, yellow cross
point is displayed.
2. Click again to make another point. The point is
connected as sky blue line from previous point.
Note:
•
When you select all of 4 points, area is set
automatically.
•
To set the Privacy Mask area, each four vertex must
be convex. If the one of 4 vertex is inside to make
concave area, the Privacy Mask area will not be set.
•
You can cancel the point by click the mouse right
button near the other point.
•
Up to 4 zone is available to set.
-
Delete: Delete the selected zone.
-
Delete All: Delete all of the mask zone.
-
Save: Save the settings of the Privacy Mask.
Note:
•
If the privacy mask setting is changed , it is not applied
immediately. You need to click the [Save] button to save
the settings.
•
When the [Image] tab is selected, the Privacy Mask area
is displayed on the preview window.
•
Set the [Privacy Mask] after setting up the [Install]
settings.
•
Privacy Mask settings area is not maintained by the
screen change by the operation of Pan / Tilt / Zoom.
When resetting the Pan / Tilt / Zoom, you need to reset
the Privacy Mask settings area also.
•
If the [Image Effect] is changed, the [Privacy Mask]
settings will be initialized.
•
[Image Stabilization] and [Privacy Mask] cannot be used
at the same time.
•
Default: Click this button to restore back to original factory
settings.
16
Basic Setup
Profile
Select the stream [Profile1], [Profile2], [Profile3] or [Profile4]
depending on the Install Preset.
Note:
It is displayed the constraints according to the current preset
settings by mouse-over at the right-top of the current Preset.
Profile
Profile1
1080p @
1080p @
30 fps
Quad
Stream
1080p @
30 fps
1080p @
1080p @
30 fps
Triple
Stream
1080p @
30 fps
1080p @
30 fps
1080p @
Pivot
15 fps
720p @
30 fps
1080p @
60 fps
High
Framerate
720p @
D1 @ 60 fps
60 fps
> Enable: Click to activate the stream function.
> Codec: Select the video mode (Codec) from the drop-down
list. The viewer can choose among MJPEG, H.264 and H.264_
HIGH.
> Resolution: Select the resolution from the drop-down list.
> Frame Rate: Set the frame rate of the image.
Note:
Refer to the table below for the supported framerates.
If you enter an unsupported framerate, the actual encoding
framerate will be less than what was entered.
For example, when 17 fps is entered, 15 fps will be applied.
Encoding
Framerate
60
50
30
25
20
15
10
5
4
3
2
1
> GOP size: It means "Group of Pictures". The higher the GOP,
the better is the video quality of the camera. Set the value
of GOP from 1 up to 60 depending on Install Preset settings.
This setting is valid for H.264 video format only.
> Bitrate Mode: Select the Quality.
-
VBR: The bit rate may vary depending on the complexity
of the video to meet the selected quality.
-
CBR: The video quality may vary in order to preserve a
Profile2
Profile3
Profile4
720p @
CIF @ 30 fps
15 fps
30 fps
720p @
720p @
CIF @ 30 fps
30 fps
30 fps
720p @
N/A
15 fps
30 fps
720p @
720p @
N/A
30 fps
30 fps
N/A
N/A
N/A
720p @
CIF @ 30 fps
N/A
30 fps
720p @
CIF @ 30 fps
N/A
30 fps
N/A
N/A
N/A
N/A
N/A
Sensor Framerate
60
50
30
25
O
N/A
N/A
N/A
O
O
N/A
N/A
O
O
O
N/A
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Operation and settings
Hide quick links:
Advertisement
Table of Contents
