Speco ONSIP O2DP7 Owner's Manual
  1. Manuals
  2. Brands
  3. Speco Manuals
  4. IP Camera
  5. ONSIP O2DP7
  6. Owner's manual

Speco ONSIP O2DP7 Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
O
N
S
I
P
O
2
D
P
7
/
O
2
I
R
2
O
N
S
I
P
O
2
D
P
7
/
O
2
I
R
2
O2DP7/O2IR24D7W
'
'
4
D
7
W
O
w
n
e
r
s
M
a
n
u
4
D
7
W
O
w
n
e
r
s
M
a
n
u
ONSIP
a
l
a
l
Rev.1.4 (June., 2013)
1

Advertisement

Table of Contents
loading

Related Manuals for Speco ONSIP O2DP7

Summary of Contents for Speco ONSIP O2DP7

  • Page 1 ’ ’ ONSIP O2DP7/O2IR24D7W Rev.1.4 (June., 2013)
  • Page 2 Be careful to prevent moisture or water penetration into the unit. Particular attention is needed when installing ONSIP O2DP7/O2IR24D7W. The screw holes for the installation screws and pipe should be maintained water tight during the whole life time of the product.
  • Page 3 ’ ’ Caution Any changes or modifications to this device could void the warranty. Revision History Date Revision Details Sept,1 , 2011 First manual revision creation. Nov,5 , 2012 Updated Specifications June, 19 , 2013 Updated package contents, drawings Rev.1.4 (June., 2013)

  • Page 4: Table Of Contents

    Contents ................... 4 1. Introduction ................... 5 1.1. Overview ....................5 1.2. Specification ....................6 1.3. Applications of ONSIP O2DP7/O2IR24D7W ............. 8 2. Product Description................. 9 2.1. Contents ....................9 2.2. Product Preview ..................10 2.3. Physical description .................. 11 2.4.

  • Page 5: Introduction

    Real time 2-way communication is available through bidirectional audio communication feature. Designed to be a stand-alone streaming audio & video transmission device, ONSIP O2DP7/O2IR24D7W can be applied to various application area such as video security, remote video monitoring, distance education, video conference or internet broadcasting system.

  • Page 6: Specification

    Upgrade Firmware upgrade over IP network Administration Remote administration over IP network Web Viewer Simple viewing over internet explorer Client & Viewer Speco-NVR Standard CMS software Dynamic IP support DDNS support Supported Video/Audio stream encryption ID and Password protection Security...
  • Page 7 ’ ’ Sync to PC Synchronize to PC Manual Manual time setting Time management Internet Time Server Synchronize to Time Server Day light saving Active-X SDK support HTTP Rev.1.4 (June., 2013)

  • Page 8: Applications Of Onsip O2Dp7/O2Ir24D7W

    ’ ’ 1.3. Applications of ONSIP O2DP7/O2IR24D7W  Security surveillance (buildings, stores, manufacturing facilities, parking lots, banks, government facilities, military, etc.)  Remote monitoring (hospitals, kindergartens, traffic, public areas, etc.)  Teleconference (Bi-directional audio conference). Remote Learning, Internet broadcasting ...

  • Page 9: Product Description

    2. Product Description 2.1. Contents The product package contains followings: Contents Description Remarks IP camera ONSIP ONSIP O2DP7/O2IR24D7W O2DP7/O2IR24D7W main unit Ceiling mount bracket, RCA cable, Embedded Mounting bracket L-Wrench, Screws(4x30L 5EA, M3x6L 2EA) (Optional item) Software & User’s Guide...

  • Page 10: Product Preview

    ’ ’ 2.2. Product Preview 2.2.1. Preview ONSIP CMS Software ONSIP-Installer O2DP7/O2IR24D7W (Speco-NVR) (Megapixel) IP Camera PC software to view and record O2DP7(Varifocal Lens the A/V streaming data transmitted PC software to allocate an IP 3.6~16mm) from IP camera. address to the IP Camera...

  • Page 11: Physical Description

    ’ ’ 2.3. Physical description 2.3.1. External View Figure 2-1. External view of ONSIP O2DP7/O2IR24D7W 2.3.2. Rear panel Sensor In Relay Out Video Out Mic/Line In Line Out DC In Serial (pin 1 at leftmost) Figure 2-2. Rear panel of ONSIP O2DP7/O2IR24D7W...

  • Page 12: Functional Description

    ’ 2.4. Functional Description  DC 12V: Power input for supplying 12V DC power. Caution: If ONSIP O2DP7/O2IR24D7W is powered by PoE, do not plug in DC Jack with active DC power into DC power connector.  MIC/LINE IN Connect external audio source or microphone.
  • Page 13 CVBS GND Relay Out CVBS Out Sensor In - Sensor In Figure 2-3 ALARM IN/OUT and Composite Video Output Terminal of ONSIP O2DP7/O2IR24D7W Used for connecting P/T device, sensor, and composite video output. Pin assignments are as follows. Description Misc.
  • Page 14 ’ ’  SNS IN: Examples of sensing devices are infrared sensors, motion sensors, heat/smoke sensors, magnetic sensor, etc. Connect the two wires of the sensors to “SNS In”. The sensor type (NC/NO) can be set in Administrative mode. 10mA can be flown into sensor device. Multiple sensor devices can be connected in parallel.
  • Page 15 A switch provided for returning the IP camera to factory default state. Open the dome cover to access the switch. Press the switch for a few seconds while power is applied. Figure 2-6 Factory Default switch of ONSIP O2DP7/O2IR24D7W Caution: Restoring the factory default will erase all settings.

  • Page 16: On Site Installation

    ’ ’ 3. On Site Installation 3.1. Please follow through the procedures in the order of the numbers for each procedure. Mounting Knob Holes . Fix the mounting bracket. Mounting Bracket . Seat the IP camera onto the mounting Mounting Knobs bracket.

  • Page 17: Embedded Mount Bracket

    ’ ’ 3.2. Please follow through the procedures in the order of the numbers for each procedure. . Place the bracket holder above the ceiling panel through prepared hole. Bracket Holder . Prepare a 165mm diameter hole on the Ceiling Panel ceiling Recessed Mounting .
  • Page 18 ’ ’ Mounting Knob Holes Mounting Knobs Make sure to align the positions of the “mounting knobs” and “mounting knob holes” when you plug in the IP camera into the mounting bracket. Once it is firmly plugged in, twist the IP camera to the right until it is locked.

  • Page 19: Getting Started

    Brief information for first time operation of ONSIP O2DP7/O2IR24D7W is provided in this chapter. 4.1. PC Requirement Audio/Video streaming data received from ONSIP O2DP7/O2IR24D7W can be displayed or stored in a PC running client programs. Minimum requirement of the PC is described below:...

  • Page 20: Quick Installation Guide

    1) Prepare a PC to run programs for the installation and video connection (PC is needed to assign IP address to ONSIP O2DP7/O2IR24D7W) 2) In case of using PoE, connect the PC and ONSIP O2DP7/O2IR24D7W to the network using one of the following ways.
  • Page 21 ’ ’ 2. Install Speco-NVR Speco-NVR is a multi-channel CMS program for to IP camera or Video server. Install Speco-NVR on remote PC to connect to these products. It is needed to assign connection information to Speco-NVR program before connection.
  • Page 22 ’ ’ Click on the field in ③ for sorting and rearranging the list. Select network mode that best suits from the drop down list in ⑤. You can choose either Static or ADSL and Auto (DHCP), respectively. If ADSL and Auto are selected, the fields in ⑥ is deactivated.
  • Page 23 3. Remote video connection to ONSIP O2DP7/O2IR24D7W 1) Connection through Web Viewer Web Viewer offers simplest way of video connection to ONSIP O2DP7/O2IR24D7W. For video connection, enter the IP address of ONSIP O2DP7/O2IR24D7W in the URL window of Internet Explorer as : Can be omitted the [e.g.] Port 80...
  • Page 24 ’ ’ Rev.1.4 (June., 2013)
  • Page 25 SAVE button. You can see the live video when you click the live view button as below. When you exit Speco-NVR, you have to input the ID/PW, admin/1234. Details for the Speco-NVR can be found in [Speco-NVR User’s Guide].
  • Page 26 ’ ’ 4. Additional settings through connection to the Admin Page All the parameters of new IP camera follows factory default values. For more sophisticated target application it is needed to change parameters. The admin page can be connected through ”http://IP_address:HTTP_port_number”/admin.htm It is needed to enter ID and password of the administrator.

  • Page 27: Trouble Shooting

    If PoE is not applied, the power and network connection should be made through separate cables. It is recommended to use DC adaptor supplied by Speco Technology for the feeding of the power. In case of replacing the DC power supply, make sure that the power supply meets with the power requirement of the IP camera to prevent damage or malfunction.

  • Page 28: Cannot Connect To The Video

    ’ ’ 5.2. Cannot connect to the Video Check the status of the network connection through PING test. Try the following on your PC : Start > Run > Cmd > Ping IP address (Ex : Ping 172.16.42.51) If “Reply from ~”...

  • Page 29: Windows Vista Or Windows 7

    5.3. Windows Vista or Windows 7 Windows Vista and Windows 7 users need to configure UAC (User Access Control) and Privilege Level for proper recording and still video capture in Speco-NVR and Web Viewer. <Windows Vista> 1. UAC (User Access Control) configuration 1) Double-click “User Accounts”...
  • Page 30 ’ ’ <Windows 7> 1. UAC (User Access Control) configuration 1) Double-click “User Accounts” in control panel 2) Double-click “Change User Account Control setting” 3) Set to “Never notify” Rev.1.4 (June., 2013)
  • Page 31 ’ ’ 2. Privilege Level Control 1) Select “NVR” icon on the desktop 2) Click right mouse button and select “properties” 3) Check “Privilege Level” in “Compatibility” tab Rev.1.4 (June., 2013)

  • Page 32: Technical Assistance

    ’ ’ 5.4. Technical Assistance If you need any technical assistance, please contact your dealer. For immediate service please provide the following information. 1. Model name 2. MAC address and Registration number 3. Purchase date 4. Description of the problem 5.

This manual is also suitable for:

Onsip o2ir24d7w

Table of Contents