Specifications - Yamaha DM1000 Service Manual

DM1000/MB1000/SP1000

SPECIFICATIONS

General Spec
Number of scene memories
Sampling Frequency
Signal Delay
Fader
Fader Resolution
Total Harmonic Distortion *
(CH INPUT to OMNI OUT)
(Input Gain=Min.)
Frequency Response
(CH INPUT to OMNI OUT)
Dynamic Range
(maximum level to noise level)
2
Hum & Noise *
(20 Hz–20 kHz)
Rs=150 Ω
Maximum Voltage Gain
Crosstalk
(@ 1 kHz)
Input Gain=Min.
AD Input (1–16)
Analog Input
(OMNI IN 1–4)
Option Input (SLOT 1–2)
Digital Input
(2TR IN DIGITAL 1–2)
4
99
44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz
Internal
Normal rate: 44.1 kHz–10% to 48 kHz+6%
External
Double rate: 88.2 kHz–10% to 96 kHz+6%
Less than 1.6 ms CH INPUT to OMNI OUT
fs=48 kHz
Less than 0.8 ms CH INPUT to OMNI OUT
fs=96 kHz
100 mm motorized with touch sense x 17
+10 to –138, –∞ dB (1024 steps/100 mm) input faders
0 to –138, –∞ dB (1024 steps/100 mm) master faders, stereo fader
Less than 0.05% 20 Hz to 20 kHz @ +14 dB into 600 Ω
1
fs=48 kHz
Less than 0.01% 1 kHz @ +24 dB into 600 Ω
Less than 0.05% 20 Hz to 40 kHz @ +14 dB into 600 Ω
fs=96 kHz
Less than 0.01% 1 kHz @ +24 dB into 600 Ω
20 Hz–20 kHz, 0.5, –1.5 dB @ +4 dB into 600 Ω
fs=48 kHz
20 Hz–40 kHz, 0.5, –1.5 dB @ +4 dB into 600 Ω
fs=96 kHz
110 dB typ. DA Converter (OMNI OUT)
106 dB typ. AD+DA (to OMNI OUT) @ fs=48 kHz
106 dB typ. AD+DA (to OMNI OUT) @ fs=96 kHz
–128 dB Equivalent Input Noise
–86 dB residual output noise. OMNI OUT (STEREO OUT off)
Input Gain=Max. –86 dB (90 dB S/N) OMNI OUT
Input Pad =0 dB (STEREO fader at nominal level and all CH INPUT faders at minimum level)
Input Pad =0 dB
–64 dB (68 dB S/N) OMNI OUT
Input Sensitivity
(STEREO fader at nominal level and one CH INPUT fader at nominal level)
=–60 dB
74 dB CH INPUT (CH1–16) to OMNI OUT (STEREO, BUS, AUX)
80 dB adjacent input channels (CH1–16)
80 dB input to output
Phantom switch +48 V DC
Pad switch 0/20 dB attenuation
Gain control 44 dB (–60 to –16), detented
LED (red) turns on when post HA level reaches 3 dB below clipping at dig-
Peak indicator
ital domain
LED (green) turns on when post HA level reaches 20 dB below nominal at
Signal indicator
digital domain
24-bit linear, 128-times oversampling (fs=44.1, 48 kHz), 64-times over-
AD converter
sampling (fs=88.2, 96 kHz)
24-bit linear, 128-times oversampling (fs=44.1, 48 kHz), 64-times over-
AD converter
sampling (fs=88.2, 96 kHz)
Available cards Optional digital interface cards (MY16, MY8, MY4 series)
SRC On/off (1:3 and 3:1 maximum input to output sample rate ratio)