Yamaha DM1000 Service Manual page 108

Digital production console/ peak meter bridge/wooden side panels
Hide thumbs Also See for DM1000:
Table of Contents

Advertisement

DM1000/MB1000/SP1000
Judgment standard 1: The EFFECT sounds must
Judgment standard 2: The output must not include
In the same manner, recall and inspect Scenes 2
through 16.
The EFFECT functions for Scenes 2 through 16 work
as follows.
Scenes 2:
SYMPHONIC
Scenes 3:
HQ PITCH
Scenes 4:
DYNAMIC FILTER
Scenes 5:
REVERB
Scenes 6:
SYMPHONIC
Scenes 7:
HQ PITCH
Scenes 8:
DYNAMIC FILTER
Scenes 9:
REVERB
Scenes 10:
SYMPHONIC
Scenes 11:
HQ PITCH
Scenes 12:
DYNAMIC FILTER
Scenes 13:
REVERB
Scenes 14:
SYMPHONIC
Scenes 15:
HQ PITCH
Scenes 16:
DYNAMIC FILTER
7. Writing and Initializing Programs
7-1. Program Version Check Method
Press the DM1000 [SEL] key CH5, CH9, CH6, CH3,
in that order, then press the [STORE] key. This
displays the versions of the main program and the
boot program on the LCD screen.
7-2. Program Writing Method
Write the main program and the boot program with
the following method.
1) Connect the PC and the DM1000 with the USB
cable.
(The YAMAHA USB-MIDI driver must be installed
on the PC and the USB-MIDI driver must be set
to Through = Off.)
2) While holding down the MONITOR [CLEAR] key,
switch on the power for the DM1000 main unit and
continue to hold down this key until "FLASH
UPDATE" is displayed on the screen of the DM1000
main unit. For the MAIN circuit board inspection, it
is adequate to just switch on the power.
3) Start the version upgrade program (VerUp.exe).
4) Press the Browse button and select the main
program (file name dm1k.pgm) and the boot
program (file name boot.pgm) to be written.
108
be output.
any noise.
5) When you press the Load button, the program
writing is started. Never switch off the power or
disconnect the USB cable while the program is
being written.
6) In order to check that the main program and the
boot program have been written correctly, check
their versions with the method in "7-1. Program
Version Check Method".
7-3. Method for Initialization with Fader Calibration
While holding down both the FADER MODE
[DISPLAY] key and the [AUX1] key, switch On the
power switch (or within 3 seconds of switching On
the power switch, simultaneously press both the
FADER MODE [DISPLAY] key and the [AUX1] key)
to start up the system, then operate according to
the following instructions.
Continue holding down these keys until the Loading
Factory Presets message is displayed on the
DM1000 main unit screen.
Screen message
Loading Factory Presets
Start of calibration
Do not touch any faders during
Calibrating the Touch Sense..
Touch Sense calibration and do not
Do Not Touch the Faders!
obstruct movement of the faders.
Do not touch any faders during
Calibrating the Faders...
Fader calibration and do not
Do Not Touch the Faders!
obstruct movement of the faders.
Set the CH1~16, STEREO Fader
Adjust CH1-16 -INFINITY
to -∞, then press the [ENTER]
STEREO -INFINITY
switch.
Hit ENTER key
Set the CH 1~16 Fader to -15dB
Adjust CH1-16 -15dB
and the STEREO Fader to -30dB,
STEREO -30dB
then press the [ENTER] switch.
Hit ENTER key
Set the CH 1~16 Fader to 0dB.
Adjust CH1-16 0dB
There is no particular need to operate the
STEREO Any Position
STEREO Fader. When this setting is
Hit ENTER key
complete, press the [ENTER] switch.
Set the CH 1~16 Fader to 10 dB
Adjust CH1-16 +10dB
and the STEREO Fader to 0 dB,
STEREO 0dB
then press the [ENTER] switch.
Hit ENTER key
After the initialization is complete, check that the DIO
WORD SELECT screen is displayed.
7-4. Method for Initializing without Fader Calibration
While holding down both the AUX SELECT
[DISPLAY] key and the [AUX8] key, switch On the
power switch (or within 3 seconds of switching On
the power switch, simultaneously press both the
FADER MODE [DISPLAY] key and the [AUX8] key)
to start up the system. Check that the DIO WORD
CLOCK SELECT screen is displayed.
Continue holding down these keys until the Loading
Factory Presets message is displayed on the
DM1000 main unit screen.
Operation contents

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Sp1000Mb1000

Table of Contents