Meiligao (MEITRACK), or transmitted in any form, either electronically or mechanically, including photocopying and recording. In no event shall Meiligao (MEITRACK) be liable for direct, indirect, special, incidental, or consequential damages (including but not limited to economic loss, personal injury, and loss of asset and property) arising out of the use or inability or illegality to use the product or documentation.
File Name: MEITRACK T1 User Guide Creator: Cavana Cheung Project: Creation Date: 2011-07-18 Update Date: 2013-01-31 Sub Project: User Guide Page: - 6 - of 22 Revision: V1.7 Confidential: External Documentation Insert the SIM card by sliding it into the card holder with the chip module facing to the connectors on PCB.
Page 7
File Name: MEITRACK T1 User Guide Creator: Cavana Cheung Project: Creation Date: 2011-07-18 Update Date: 2013-01-31 Sub Project: User Guide Page: - 7 - of 22 Revision: V1.7 Confidential: External Documentation Click on the link then the location can be shown directly on Google Maps on your mobile phone.
Confidential: External Documentation More SMS commands You can configure T1 by mobile phone or by computer using the MEITRACK Parameter Editor. For more details, please refer to part 6.5 Configure by Computer. Note: Password is 4 digits only and defaulted as 0000. You can change the password by using the Parameter Editor and SMS command.
File Name: MEITRACK T1 User Guide Creator: Cavana Cheung Project: Creation Date: 2011-07-18 Update Date: 2013-01-31 Sub Project: User Guide Page: - 9 - of 22 Revision: V1.7 Confidential: External Documentation Authorize a phone number to make a silent call to the tracker. The tracker will answer the call automatically and allows the caller to listen to what is happening around the tracker.
This part mainly shows you how to use the MEITRACK Parameter Editor. Note: Don’t connect T1 to external battery when configuring. Please refer to the MEITRACK Parameter Editor User Guide for more information regarding configuration and functions. Run ‘PL2303_Prolific_DriverInstaller’ to install the driver for the USB data cable.
Page 11
‘Prolific USB-to-Serial Comm Port’ as the following picture shows. Note: Remember this Com number. It needs to be input into the MEITRACK Parameter Editor. It is COM3 in this example and it would be COM4 or COM5… in your computer.
Click ‘Read Settings’ button to show the default or previous settings of the tracker. Note: MEITRACK Parameter Editor is in the CD. The language will be automatically adjusted to be the same as your PC operation system’s language. Please use “Ctrl+L” to change the language.
Page 13
Event Selected event’s SMS reports will be sent to the authorized phone number. For more details, please refer to MEITRACK GPRS/SMS Protocol. For description of events from SOS/Input 1 Active to Tow Alarm, please refer to tap II GPRS Tracking.
File Name: MEITRACK T1 User Guide Creator: Cavana Cheung Project: Creation Date: 2011-07-18 Update Date: 2013-01-31 Sub Project: User Guide Page: - 18 - of 22 Revision: V1.7 Confidential: External Documentation Output low voltage sink current (effective): 400mA max. 7.1.1 Power/GND (PIN1/PIN2) Connect GND (-Black) and Power (+Red) wires to the battery of vehicle.
File Name: MEITRACK T1 User Guide Creator: Cavana Cheung Project: Creation Date: 2011-07-18 Update Date: 2013-01-31 Sub Project: User Guide Page: - 20 - of 22 Revision: V1.7 Confidential: External Documentation 1.1*AD value Percentage Left = * 100% 4096* 2 – 1.1*AD value The value must be converted into decimal, for example, 0x0313 is 787 in decimal.
File Name: MEITRACK T1 User Guide Creator: Cavana Cheung Project: Creation Date: 2011-07-18 Update Date: 2013-01-31 Sub Project: User Guide Page: - 21 - of 22 Revision: V1.7 Confidential: External Documentation White Reserved (RFID Reader RS232 RX, T1 TX) Note: This interface also supports handset. It only can be used to connect to handset or RFID reader at the same time.
File Name: MEITRACK T1 User Guide Creator: Cavana Cheung Project: Creation Date: 2011-07-18 Update Date: 2013-01-31 Sub Project: User Guide Page: - 22 - of 22 Revision: V1.7 Confidential: External Documentation 7.6 Mount the T1 unit If mounting required, there are 4 screw holes on the T1, 2 along either side that act as fixing points to the vehicle Please do not hesitate to email us at info@meitrack.com...
Need help?
Do you have a question about the GPS Vehicle Tracker and is the answer not in the manual?
Questions and answers