Page 2 Vigor2925 Series User’s Guide...
Page 3 Vigor2925 Series Dual-WAN Security Router User’s Guide Version: 3.0 Firmware Version: V3.7.6 (For future update, please visit DrayTek web site) Date: December 3, 2014 Vigor2925 Series User’s Guide...
Page 4: Copyright Information
Web registration is preferred. You can register your Vigor router via Owner http://www.dayTek.com. Firmware & Tools Due to the continuous evolution of DrayTek technology, all routers will be regularly Updates upgraded. Please consult the DrayTek web site for more information on newest firmware, tools and documents.
Page 5: European Community Declarations
Product: Vigor2925 Series Router DrayTek Corp. declares that Vigor2925 Series of routers are in compliance with the following essential requirements and other relevant provisions of R&TTE 1999/5/EC, ErP 2009/125/EC and RoHS 2011/65/EU The product conforms to the requirements of Electro-Magnetic Compatibility (EMC) Directive 2004/108/EC by complying with the requirements set forth in EN55022/Class B and EN55024/Class B.
Page 6 Vigor2925 Series User’s Guide...
Page 7: Table Of Contents
Introduction....................1 1.1 Web Configuration Buttons Explanation ................. 2 1.2 LED Indicators and Connectors ....................3 1.2.1 For Vigor2925 ........................3 1.2.2 For Vigor2925n ......................... 5 1.2.3 For Vigor2925n-plus ......................7 1.2.4 For Vigor2925Vn-plus....................... 9 1.2.5 For Vigor2925F....................... 11 1.2.6 For Vigor2925Fn......................13 1.3 Hardware Installation ......................
Page 8 Tutorials and Applications.................73 3.1 How to configure settings for IPv6 Service in Vigor2925............73 3.2 How can I get the files from USB storage device connecting to Vigor router? ..... 86 3.3 How to Build a LAN-to-LAN VPN Between Remote Office and Headquarter via IPSec Tunnel (Main Mode) ..........................
Page 9 4.2.7 Wired 802.1x......................... 218 4.2.8 Web Portal Setup......................219 4.3 Load-Balance /Route Policy....................220 4.4 NAT ............................. 232 4.4.1 Port Redirection ......................233 4.4.2 DMZ Host........................236 4.4.3 Open Ports........................240 4.4.4 Port Triggering ......................242 4.5 Hardware Acceleration ......................245 4.5.1 Setup..........................
Page 10 4.11.9 SMS / Mail Alert Service ..................... 346 4.11.10 Bonjour ........................348 4.12 VPN and Remote Access....................351 4.12.1 Remote Access Control ....................352 4.12.2 PPP General Setup ....................352 4.12.3 IPSec General Setup ....................354 4.12.4 IPSec Peer Identity ..................... 355 4.12.5 Remote Dial-in User ....................
Page 11 5.3 Pinging the Router from Your Computer ................523 5.4 Checking If the ISP Settings are OK or Not ................ 524 5.5 Problems for 3G Network Connection ................524 5.6 Backing to Factory Default Setting If Necessary ..............525 5.7 Contacting DrayTek......................526 Vigor2925 Series User’s Guide...
Page 13: Introduction
Vigor2925 series integrates IP layer QoS, NAT session/bandwidth management to help users control works well with large bandwidth. By adopting hardware-based VPN platform and hardware encryption of AES/DES/3DES, the router increases the performance of VPN greatly, and offers several protocols (such as IPSec/PPTP/L2TP) with up to 32 VPN tunnels.
Page 14: Web Configuration Buttons Explanation
Several main buttons appeared on the web pages are defined as the following: Save and apply current settings. Cancel current settings and recover to the previous saved settings. Clear all the selections and parameters settings, including selection from drop-down list. All the values must be reset with factory default settings. Add new settings for specified item.
Page 15: Led Indicators And Connectors
Before you use the Vigor router, please get acquainted with the LED indicators and connectors first. Status Explanation ACT (Activity) Blinking The router is powered on and running normally. The router is powered off. USB1~USB2 USB device is connected and ready for use. Blinking The data is transmitting.
Page 16 Interface Description Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for more than 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration.
Page 17: For Vigor2925N
Status Explanation ACT (Activity) Blinking The router is powered on and running normally. The router is powered off. USB device is connected and ready for use. Blinking The data is transmitting. WLAN Wireless access point is ready. Blinking It will blink slowly while wireless traffic goes through. ACT and WLAN LEDs blink quickly and simultaneously when WPS is working, and will return to normal condition after two minutes.
Page 18 Interface Description Wireless LAN Press "Wireless LAN ON/OFF/WPS" button once to wait for client ON/OFF/WPS device making network connection through WPS. Press "Wireless LAN ON/OFF/WPS" button twice to enable (WLAN LED on) or disable (WLAN LED off) wireless connection. Factory Reset Restore the default settings.
Page 19: For Vigor2925N-Plus
Status Explanation ACT (Activity) Blinking The router is powered on and running normally. The router is powered off. USB device is connected and ready for use. Blinking The data is transmitting. 2.4G Wireless access point with transmission rate of 2.4G is ready.
Page 20 Interface Description Wireless LAN Press "Wireless LAN ON/OFF/WPS" button once to wait for ON/OFF/WPS client device making network connection through WPS. Press "Wireless LAN ON/OFF/WPS" button twice to enable (WLAN LED on) or disable (WLAN LED off) wireless connection. Factory Reset Restore the default settings.
Page 21: For Vigor2925Vn-Plus
Status Explanation ACT (Activity) Blinking The router is powered on and running normally. The router is powered off. USB device is connected and ready for use. Blinking The data is transmitting. 2.4G Wireless access point with transmission rate of 2.4G is ready.
Page 22 Interface Description Wireless LAN Press "Wireless LAN ON/OFF/WPS" button once to wait for ON/OFF/WPS client device making network connection through WPS. Press "Wireless LAN ON/OFF/WPS" button twice to enable (WLAN LED on) or disable (WLAN LED off) wireless connection. Factory Reset Restore the default settings.
Page 23: For Vigor2925F
Status Explanation ACT (Activity) Blinking The router is powered on and running normally. The router is powered off. USB1~USB2 USB device is connected and ready for use. Blinking The data is transmitting. WAN1~WAN2 Internet connection is ready. Internet connection is not ready. Blinking The data is transmitting.
Page 24 Interface Description Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for more than 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration.
Page 25: For Vigor2925Fn
Status Explanation ACT (Activity) Blinking The router is powered on and running normally. The router is powered off. USB device is connected and ready for use. Blinking The data is transmitting. WLAN Wireless access point is ready. Blinking It will blink slowly while wireless traffic goes through. ACT and WLAN LEDs blink quickly and simultaneously when WPS is working, and will return to normal condition after two minutes.
Page 26 Interface Description Wireless LAN Press "Wireless LAN ON/OFF/WPS" button once to wait for client ON/OFF/WPS device making network connection through WPS. Press "Wireless LAN ON/OFF/WPS" button twice to enable (WLAN LED on) or disable (WLAN LED off) wireless connection. Factory Reset Restore the default settings.
Page 27: Hardware Installation
Before starting to configure the router, you have to connect your devices correctly. In this section, Vigor2925n is taken as an example. Connect the cable Modem/DSL Modem/Media Converter to any WAN port of router with Ethernet cable (RJ-45). Connect one end of an Ethernet cable (RJ-45) to one of the LAN ports of the router and the other end of the cable (RJ-45) into the Ethernet port on your computer.
Page 28 For the installation of Vigor2829Vn-plus, refer to the following figure: Vigor2925 Series User’s Guide...
Page 29: Printer Installation
You can install a printer onto the router for sharing printing. All the PCs connected this router can print documents via the router. The example provided here is made based on Windows 7. For other Windows system, please visit www.DrayTek.com. Before using it, please follow the steps below to configure settings for connected computers (or wireless clients).
Page 30 Click Add a printer. A dialog will appear. Click Add a local printer and click Next. In this dialog, choose Create a new port. In the field of Type of port, use the drop down list to select Standard TCP/IP Port. Then, click Next. Vigor2925 Series User’s Guide...
Page 31 In the following dialog, type 192.168.1.1 (router’s LAN IP) in the field of Hostname or IP Address and type 192.168.1.1 as the Port name. Then, click Next. Click Standard and choose Generic Network Card. Vigor2925 Series User’s Guide...
Page 32 Now, your system will ask you to choose right name of the printer that you installed onto the router. Such step can make correct driver loaded onto your PC. When you finish the selection, click Next. Type a name for the chosen printer. Click Next. Vigor2925 Series User’s Guide...
Page 33 10. Choose Do not share this printer and click Next. 11. Then, in the following dialog, click Finish. Vigor2925 Series User’s Guide...
Page 34 12. The new printer has been added and displayed under Printers and Faxes. Click the new printer icon and click Printer server properties. 13. Edit the property of the new printer you have added by clicking Configure Port. Vigor2925 Series User’s Guide...
Page 35 Note 1: Some printers with the fax/scanning or other additional functions are not supported. If you do not know whether your printer is supported or not, please visit www.draytek.com to find out the printer list. Open Support >FAQ/Application Notes; find out the link of USB>>Printer Server and click it.
Page 36: Accessing Web Page
Then, click the What types of printers are compatible with Vigor router? link. Note 2: Vigor router supports printing request from computers via LAN ports but not WAN port. Make sure your PC connects to the router correctly. You may either simply set up your computer to get IP dynamically from the router or set up the IP address of the computer to be the same subnet as the default IP address of Vigor router 192.168.1.1.
Page 37: Changing Password
Note: The home page will be different slightly in accordance with the type of the router you have. The web page can be logged out according to the chosen condition. The default setting is Auto Logout, which means the web configuration system will logout after 5 minutes without any operation.
Page 38: Introducing Dashboard
Enter the login password (the default is “admin”) on the field of Old Password. Type New Password. Then click OK to continue. Note: The maximum length of the password you can set is 23 characters. Now, the password has been changed. Next time, use the new password to access the Web user interface for this router.
Page 39: Virtual Panel
On the top of the Dashboard, a virtual panel (simulating the physical panel of the router) displays the physical interface connection. It will be refreshed every five seconds. Port Color Explanation Displayed Ethernet Port Black It means such port is disconnected. (WAN/LAN) Green It means such port is connected (with Giga transmission...
Page 40: Name With A Link
A name with a link (e.g., Router Name, Current Time, WAN1/2/3 and etc.) below means you can click it to open the configuration page for modification. All the menu items can be accessed and arranged orderly on the left side of the main page for your request.
Page 41: Gui Map
Note that there is a plus ( ) icon located on the left side of VPN/LAN. Click it to review the VPN connection(s) used presently. Host connected physically to the router via LAN port(s) will be displayed with green circles in the field of Connected.
Page 42: Web Console
It is not necessary to use the telnet command via DOS prompt. The changes made by using web console have the same effects as modified through web user interface. The functions/settings modified under Web Console also can be reviewed on the web user interface.
Page 43: Config Backup
There is one way to store current used settings quickly by clicking the Config Backup icon. It allows you to backup current settings as a file. Such configuration file can be restored by using System Maintenance>>Configuration Backup. Simply click the icon on the top of the main screen and a pop up dialog will appear. Click Save to store the setting.
Page 44 Detailed explanation (for IPv4) is shown below: Item Description LAN Status Primary DNS-Displays the primary DNS server address for WAN interface. Secondary DNS -Displays the secondary DNS server Vigor2925 Series User’s Guide...
Page 45 Item Description address for WAN interface. IP Address-Displays the IP address of the LAN interface. TX Packets-Displays the total transmitted packets at the LAN interface. RX Packets-Displays the total received packets at the LAN interface. WAN1/WAN2/WAN3 Enable – Yes in red means such interface is available but /WAN4 Status not enabled.
Page 46: Virtual Wan
Item Description gateway. Note: The words in green mean that the WAN connection of that interface is ready for accessing Internet; the words in red mean that the WAN connection of that interface is not ready for accessing Internet. Such page displays the virtual WAN connection information. Virtual WAN are used by TR-069 management, VoIP service and so on.
Page 47: Quick Setup
There are several setup wizards offered for you to configure the router simply and quickly.  Quick Start Wizard – used for building network connection, Internet access.  Service Activation Wizard – used for activating the web content filter service. ...
Page 48 On the next page as shown below, please select the WAN interface that you use. If Ethernet interface is used, please choose WAN1/WAN2; if 3G/4G USB modem is used, please choose WAN3/WAN4. Then click Next for next step. WAN1, WAN2, WAN3 and WAN4 will bring up different configuration page. Refer to the following for detailed information.
Page 49: For Wan1/Wan2 (Ethernet)
WAN1/WAN2 is dedicated to physical mode in Ethernet. If you choose WAN1/WAN2, please specify physical type. Then, click Next. On the next page as shown below, please select the appropriate Internet access type according to the information from your ISP. For example, you should select PPPoE mode if the ISP provides you PPPoE interface.
Page 50 Click PPPoE as the Internet Access Type. Then click Next to continue. Available settings are explained as follows: Item Description Service Name Enter the description of the specific network service. (Optional) Username Assign a specific valid user name provided by the ISP. Note: The maximum length of the user name you can set is 63 characters.
Page 51 Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown. Now, you can enjoy surfing on the Internet. Choose WAN1/WAN2 as the WAN Interface and click the Next button. The following page will be open for you to specify Internet Access Type.
Page 52 Click PPTP/L2TP as the Internet Access Type. Then click Next to continue. Available settings are explained as follows: Item Description Username Assign a specific valid user name provided by the ISP. Note: The maximum length of the user name you can set is 63 characters.
Page 53 Cancel Click it to give up the quick start wizard. Please type in the IP address/mask/gateway information originally provided by your ISP. Then click Next for viewing summary of such connection. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown.
Page 54 Click Static IP as the Internet Access type. Simply click Next to continue. Available settings are explained as follows: Item Description WAN IP Type the IP address. Subnet Mask Type the subnet mask. Gateway Type the IP address of gateway. Type in the primary IP address for the router.
Page 55 Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown. Now, you can enjoy surfing on the Internet. Choose WAN2 as WAN Interface and click the Next button. The following page will be open for you to specify Internet Access Type.
Page 56 39 characters. Some Cable service providers specify a specific MAC address for access authentication. In such cases you need to enter the MAC address. Back Click it to return to previous setting page. Next Click it to get into the next setting page. Cancel Click it to give up the quick start wizard.
Page 57: For Wan3/Wan4 (Usb)
WAN3 is dedicated to physical mode in USB. If WAN3 is selected, it is not necessary for you to type any information for such connection. Choose WAN3/WAN4 as WAN Interface. Then, click Next for getting the following page. Available settings are explained as follows: Item Description Internet Access...
Page 58 APN Name – APN means Access Point Name which is provided and required by some ISPs. Type the name and click Apply. Then, click Next for viewing summary of such connection. Click Finish. A page of Quick Start Wizard Setup OK!!! will appear. Then, the system status of this protocol will be shown.
Page 59: Service Activation Wizard
Service Activation Wizard is a tool which allows you to use trial version or update the license of WCF directly without accessing into the server (MyVigor) located on http://myvigor.draytek.com. For using Web Content Filter Profile, please refer to later section Web Content Filter Profile for detailed information.
Page 60 When you finish the selection, please click Next. Commtouch is the web content filter based on Commtouch operated in the worldwide. There is a 30-day trial period. After trial, you can purchase DrayTek's prepared Commtouch GlobalView WCF package from retailing outlets.
Page 61 Wait for a moment till the following page appears. When such page appears, you can enable or disable these services for your necessity. Then, click Finish. Note: The service will be activated and applied as the default rule configured in Firewall>>General Setup.
Page 62 Vigor2925 Series User’s Guide...
Page 63: Vpn Client Wizard
Such wizard is used to configure VPN settings for VPN client. Such wizard will guide to set the LAN-to-LAN profile for VPN dial out connection (from server to client) step by step. 1. Open VPN and Remote Access>>VPN Client Wizard. The following page will appear. Available settings are explained as follows: Item Description...
Page 64 2. When you finish the mode and profile selection, please click Next to open the following page. In this page, you have to select suitable VPN type for the VPN client profile. There are six types provided here. Different type will lead to different configuration page. After making the choices for the client profile, please click Next.
Page 65 Note: The following descriptions for VPN Type are based on the Route Mode specified in LAN-to-LAN Client Mode Selection.  When you choose PPTP (None Encryption) or PPTP (Encryption), you will see the following graphic:  When you choose IPsec, you will see the following graphic: ...
Page 66  When you choose L2TP over IPsec (Nice to Have) or L2TP over IPsec (Must), you will see the following graphic: Available settings are explained as follows: Item Description Profile Name Type a name for such profile. The length of the file is limited to 10 characters.
Page 67 VPN Dial-Out Use the drop down menu to choose a proper WAN interface Through for this profile. This setting is useful for dial-out only. WAN1 First/ WAN2 First /WAN3 First/WAN4 First- While connecting, the router will use WAN1/WAN2/WAN3/WAN4 as the first channel for VPN connection.
Page 68 is active. High - Encapsulating Security Payload (ESP) means payload (data) will be encrypted and authenticated. You may select encryption algorithm from Data Encryption Standard (DES), Triple DES (3DES), and AES. User Name This field is used to authenticate for connection when you select PPTP or L2TP with or without IPsec policy above.
Page 69: Vpn Server Wizard
Such wizard is used to configure VPN settings for VPN server. Such wizard will guide to set the LAN-to-LAN profile for VPN dial in connection (from client to server) step by step. 1. Open VPN and Remote Access>>VPN Server Wizard. The following page will appear. Available settings are explained as follows: Item Description...
Page 70 Please choose a This item is available when you choose Remote Dial-in Dial-in User User (Teleworker) as VPN server mode. There are 32 VPN Accounts tunnels for users to set. Allowed Dial-in Type This item is available after you choose any one of dial-in user account profiles.
Page 71  When you check PPTP, you will see the following graphic:  When you check PPTP & IPsec & L2TP (three types) or PPTP & IPsec (two types) or L2TP with Policy (Nice to Have/Must), you will see the following graphic: Vigor2925 Series User’s Guide...
Page 72  When you check IPsec, you will see the following graphic: Available settings are explained as follows: Item Description Type a name for such profile. The length of the file is Profile Name limited to 10 characters. User Name This field is used to authenticate for connection when you select PPTP or L2TP with or without IPsec policy above.
Page 73 Remote Network IP Please type one LAN IP address (according to the real location of the remote host) for building VPN connection. Remote Network Please type the network mask (according to the real location Mask of the remote host) for building VPN connection. 3.
Page 74: Wireless Wizard
Description Wireless 2.4GHz Settings Name Type the SSID name of this router for wireless 2.4GHz. The default name is defined with DrayTek. Change the name if required. Mode At present, the router can connect to 11n Only, 11g Only, Mixed (11b+11g), Mixed (11a+11n), Mixed (11g+11n), and Mixed (11b+11g+11n) stations simultaneously.
Page 75 choose Mix (11b+11g+11n) mode. Channel Means the channel of frequency of the wireless LAN. The default channel is 6. You may switch channel if the selected channel is under serious interference. If you have no idea of choosing the frequency, please select Auto to let system determine for you.
Page 76 Next Click it to get into the next setting page. Cancel Exit the wireless wizard without saving any changes. 3. After typing the required information, click Next. The settings in the page limit the wireless station (guest) accessing into Internet but not being allowed to share the LAN network and VPN connection.
Page 77 Wireless 5GHz Settings Enable/Disable Click it to enable or disable settings in this page. Use the same SSID Check the box to use the same settings configured above. and Security Key as above SSID Type the SSID name of this router. (SSID2) Security Key The wireless mode offered by this wizard is WPA2/PSK.
Page 78: Voip Wizard
Vigor router offers a quick method to configure settings for VoIP application. Follow the steps listed below. Note: This wizard is available for “V” model only. 1. Open Wizards>>VoIP Wizard. 2. The screen of VoIP Wizard will be shown as follows. Available settings are explained as follows: Item Description...
Page 79 Cancel Click it to give up the quick start wizard. 3. After finished the settings above, click Next for viewing summary of such connection. 4. Click Finish. A page of VoIP Wizard Setup OK!!! will appear. Vigor2925 Series User’s Guide...
Page 80: Registering Vigor Router
You have finished the configuration of Quick Start Wizard and you can surf the Internet at any time. Now it is the time to register your Vigor router to MyVigor website for getting more service. Please follow the steps below to finish the router registration. Please login the web configuration interface of Vigor router by typing “admin/admin”...
Page 81 Notice: If you haven’t an accessing account, please refer to section 3.8 Creating an Account for MyVigor on User’s Guide to create your own one. Please read the articles on the Agreement regarding user rights carefully while creating a user account.
Page 82 When the following page appears, your router information has been added to the database. Now, you have finished the product registration. After clicking OK, you will see the following page. Your router has been registered to myvigor website successfully. If you have not activated web content filter service by using Service Activation Wizard, you can activate the service from this step.
Page 83 When this page appears, click Register. Wait for a moment until the following page appears. Click Close. Vigor2925 Series User’s Guide...
Page 84 This page is left blank. Vigor2925 Series User’s Guide...
Page 85: Tutorials And Applications
Due to the shortage of IPv4 address, more and more countries use IPv6 to solve the problem. However, to continually use the original rich resources of IPv4, both IPv6 and IPv4 networks shall communicate for each other via intercommunication mechanism to complete the shifting job from IPv4 to IPv6 gradually.
Page 86 Note: Only one WAN interface support IPv6 service at one time. In this example, WAN2 is chosen as the one supporting IPv6 service. In the following figure, use the drop down list to choose a proper connection type. Different connection types will bring out different configuration page. Refer to the following: ...
Page 87 Click OK and open Online Status. If the connection is successful, you will get the IP address for IPv4 and IPv6 at the same time. Vigor2925 Series User’s Guide...
Page 88 Vigor2925 Series User’s Guide...
Page 89  TSPC – Tunnel application, both IPv6 hosts communicate through IPv4 network Choose TSPC and type the information for TSPC service. Note: While using such mode, you have to make sure the IPv4 network connection is normal. (In the following figure, the TSPC information is obtained from http://gogo6.com/ after applied for the service.) Click OK and open Online Status.
Page 90  AICCU – Tunnel application Choose AICCU and type the information for AICCU of IPv6. Note: While using such mode, you have to make sure the IPv4 network connection is normal. (In the following figure, the AICCU information is obtained from https://www.sixxs.net/main/ after applied for the service.) Click OK and open Online Status.
Page 91  DHCPv6 Client Choose DHCPv6 Client. Click one of the identity associations and type the IAID number. Click OK and open Online Status. If the connection is successful, the physical connection will be shows as follows: Vigor2925 Series User’s Guide...
Page 92  Static IPv6 Choose Static IPv6. Type IPv6 address, Prefix Length and Gateway Address. Click OK and open Online Status. If the connection is successful, the physical connection will be shows as follows: Vigor2925 Series User’s Guide...
Page 93  6in4 Static Tunnel Choose 6in4 Static Tunnel. Type remote endpoint IPv4 address, 6in4 IPv6 Address, LAN Routed Prefix and Tunnel TTL. Click OK and open Online Status. If the connection is successful, the physical connection will be shows as follows: Vigor2925 Series User’s Guide...
Page 94  Choose 6rd. Type IPv4 Border Relay, IPv4 Mask Length, 6rd Prefix and 6rd Prefix Length. Click OK and open Online Status. If the connection is successful, the physical connection will be shows as follows: Vigor2925 Series User’s Guide...
Page 95 After finished the WAN settings for IPv6, please configure the LAN settings to make the router’s client getting the IPv6 address. Access into the web user interface of Viogr2925. Open LAN>> General Setup. Click the IPv6 button. Note: Only the subnet of LAN1 supports IPv6 feature. In the field of Router Advertisement Server, the default setting is Enable.
Page 96 Make sure you have get the correct IPv6 IP address. Get into MS-DOS interface and type the command of “ipconfig”. Refer to the following figure. From the above figure we can see IPv6 IP address has been captured by the system. Use the Ping command to ping any IPv6 address indicating an IPv6 website.
Page 97 Connect to the website for IPv6. Open a web browser and type an URL of IPv6, e.g., www.kame.net. If your computer accesses into the website by using IPv6 address, you may see a turtle dancing on the screen. If not, only a steady turtle will be seen. If you can see a turtle dancing on the screen, that means IPv6 service is ready for you to access and utilize.
Page 98: How Can I Get The Files From Usb Storage Device Connecting To Vigor Router
Files on USB storage device can be reviewed by opening USB Applicaiton>>File Explorer. If it is necessary for you to delete, copy files on the device or write, paste files to the devcie, it must be done through SAMBA server or FTP server. Samba service is based on the original USB FTP service.
Page 99 Setup a user account for the FTP service by using USB Application >>USB User Management. Click Enable to enable FTP/Samba User account. Here we add a new account "user1" and assign authorities “Read”, “Write” and “List” to it. Click OK to save the configuration. Make sure the FTP service is running properly.
Page 100 When the following screen appears, it means the FTP service is running properly. Return to USB Application >> USB Disk Status. The information for FTP server will be shown as below. Now, users in LAN of Vigor2925 can access into the USB storage device by typing ftp://192.168.1.1 on any browser.
Page 101: (Main Mode)
Log into the web user interface of Vigor router. Open VPN and Remote Access>>LAN to LAN to create a LAN-to-LAN profile. Click any index number to open the configuration page. Type a name which is easy for identification for such profile (in this case, type VPN Server), and check the box of Enable This Profile.
Page 102 Now navigate to the next section, Dial-In Settings to check PPTP, IPSec Tunnel and L2TP boxes. Check the box of Specify Remote… and type the Peer VPN Server IP (e.g., 218.242.130.19 in this case). Press the IKE Pre-Shared Key button to set the PSK; and select Medium (AH) or High (ESP) as the security method.
Page 103 Open VPN and Remote Access>>Connection Management to check the dial-in connection status (from branch office). Log into the web user interface of Vigor router. Open VPN and Remote Access>>LAN to LAN to create a LAN-to-LAN profile. The following settings are for a permanent VPN connection. Click any index number to open the configuration page.
Page 104 Now navigate to the next section, Dial-Out Settings to select the IPSec Tunnel service and type the remote server IP/host name (e.g., 218.242.133.91, in this case). Press the IKE Pre-Shared Key button to set the PSK; and select Medium (AH) or High (ESP) as the security method.
Page 105: How To Optimize The Bandwidth Through Qos Technology
Internet connection line? The advanced bandwidth management technology-QoS (Quality of Service) helps you to well allocate the bandwidth upon your demand of Voice, Video, or Data transferring. Let's see how to get the optimum bandwidth per your request by using DrayTek Vigor router as below.
Page 106 Check the box of ACT. Click Edit to specify the local address. In the pop-up window, choose Range Address as the Address Type and type the start IP address and end IP address in relational fields. Click OK to save the settings and exit the window.
Page 107 The class rule for VoIP has been set. Click OK to return to previous page. Do the same steps to add class rules for IPTV and Data/Email with IP addresses as shown below. Vigor2925 Series User’s Guide...
Page 108 Assuming you get 2MB/512Kb Internet line. You can click the Setup link of WAN1 to set up the bandwidth for different groups among VoIP, IPTV and Data/Email. 10. In the Setup page, check the box of Enable the QoS Control. Type 30, 50 and 15 in the boxes for VoIP, IPTV and Data/Email respectively.
Page 109: Qos Setting Example
Assume a teleworker sometimes works at home and takes care of children. When working time, he would use Vigor router at home to connect to the server in the headquarter office downtown via either HTTPS or V PN to check email and access internal database. Meanwhile, children may chat on Skype in the restroom.
Page 110 Return to previous page. Enter the Name of Index Class 1 by clicking Edit link. Type the name “E-mail” for Class 1. Click OK to save the settings. Click the Setup link for WAN2. The user can set reserved bandwidth (e.g., 25%) for E-mail using protocol POP3 and SMTP.
Page 111 Click Setup link for WAN2. Check Enable UDP Bandwidth Control on the bottom to prevent enormous UDP traffic influent other application. Click OK. If the worker has connected to the headquarter using host to host VPN tunnel. (Please refer to Chapter 3 VPN for detail instruction), he may set up an index for it. Enter the Class Name of Index 3.
Page 112 10. Click Edit for Class 3 to open a new window. In this index, the user will set reserved bandwidth for VPN. 11. Click Add to open the following window. Check the ACT box, first. 12. Then click Edit of Local Address to set a worker’s subnet address. Click Edit of Remote Address to set headquarter’s IP address.
Page 113: How To Use Landing
Landing Page is a special feature configured under User Management. It can specify the message, content to be seen or specify which website to be accessed into when users try to access into the Internet by passing the authentication. Here, we take Vigor2925 series router as an example.
Page 114 In the following page, check the box of Landing page and click OK to save the settings. Open any browser (e.g., FireFox, Internet Explorer). The logging page will appear and asks for username and password. Please type the correct username and password. Click Login.
Page 115 In the field of Landing Page, please type the words as below: “ <body stats=1><script language='javascript'> window.location='http://www.draytek.com'</script></body>” Next, enable the Landing Page function. Open User Management -> User Profile and click one of the index number (e.g., index number 3) links.
Page 116 Open any browser (e.g., FireFox, Internet Explorer). The logging page will appear and asks for username and password. Please type the correct username and password. Click Login. If the logging is successful, you will be directed into the website of www.draytek.com. Vigor2925 Series User’s Guide...
Page 117: How To Send A Notification To Specified Phone Number Via Sms Service In Wan Disconnection
Follow the steps listed below: Log into the web user interface of Vigor router. Configure relational objects first. Open Object Settings>>SMS/Mail Server Object to get the following page. Index 1 to Index 8 allows you to choose the built-in SMS service provider. If the SMS service provider is not on the list, you can configure Index 9 and Index 10 to add the new service provider to Vigor router.
Page 118 After finished the settings, click OK to return to previous page. Now you have finished the configuration of the SMS Provider profile setting. Open Object Settings>>Notification Object to configure the event conditions of the notification. Choose any index number (e.g., Index 1 in this case) to configure conditions for sending the SMS.
Page 119 After finished the settings, click OK to return to previous page. You have finished the configuration of the notification object profile setting. Now, open Application >> SMS / Mail Alert Service. Use the drop down list to choose SMS Provider and the Notify Profile (specify the time of sending SMS). Then, type the phone number in the field of Recipient (the one who will receive the SMS).
Page 120 Choose one of the Index numbers (9 or 10) allowing you to customize the SMS Provider. In the web page, type the URL string of the SMS provider and type the username and password. After clicking OK, the new added SMS provider will be added and will be available for you to specify for sending SMS out.
Page 121: How To Create An Account For Myvigor
The website of MyVigor (a server located on http://myvigor.draytek.com) provides several useful services (such as Anti-Spam, Web Content Filter, Anti-Intrusion, and etc.) to filtering the web pages for the sake of protecting your system. To access into MyVigor for getting more information, please create an account for MyVigor.
Page 122 2. Click the Activate link. A login page for MyVigor web site will pop up automatically. 3. Click the link of Create an account now. 4. Check to confirm that you accept the Agreement and click Accept. Vigor2925 Series User’s Guide...
Page 123 5. Type your personal information in this page and then click Continue. 6. Choose proper selection for your computer and click Continue. Vigor2925 Series User’s Guide...
Page 124 New Account Confirmation 8. Check to see the confirmation email with the title of Letter from myvigor.draytek.com. 9. Click the Activate my Account link to enable the account that you created. The following screen will be shown to verify the register process is finished. Please click Login.
Page 125: Create An Account Via Myvigor Web Site
11. Now, click Login. Your account has been activated. You can access into MyVigor server to activate the service (e.g., WCF) that you want. 1. Access into http://myvigor.draytek.com. Find the line of Not registered yet?. Then, click the link Click here! to access into next page.
Page 126 2. Check to confirm that you accept the Agreement and click Accept. 3. Type your personal information in this page and then click Continue. 4. Choose proper selection for your computer and click Continue. Vigor2925 Series User’s Guide...
Page 127 New Account Confirmation 6. Check to see the confirmation email with the title of Letter from myvigor.draytek.com. 7. Click the Activate my Account link to enable the account that you created. The following screen will be shown to verify the register process is finished. Please click Login.
Page 128 8. When you see the following page, please type in the account and password (that you just created) in the fields of UserName and Password. Then type the code in the box of Auth Code according to the value displayed on the right side of it. Now, click Login.
Page 129: How To Configure Certain Computers Accessing To Internet
We can specify certain computers (e.g., 192.168.1.10 ~ 192.168.1.20) accessing to Internet through Vigor router. Others (e.g., 192.168.1.31 and 192.168.1.32) outside the range can get the source from LAN only. The way we can use is to set two rules under Firewall. For Rule 1 of Set 2 under Firewall>>Filter Setup is used as the default setting, we has to create a new rule starting from Filter Rule 2 of Set 2.
Page 130 Check the box of Check to enable the Filter Rule. Type the comments (e.g., block_all). Choose Block If No Further Match for the Filter setting. Then, click OK. Note: In default, the router will check the packets starting with Set 2, Filter Rule 2 to Filter Rule 7.
Page 131 A dialog box will be popped up. Choose Range Address as Address Type by using the drop down list. Type 192.168.1.10 in the field of Start IP, and type 192.168.1.20 in the field of End IP. Then, click OK to save the settings. The computers within the range can access into the Internet.
Page 132 Both filter rules have been created. Click OK. Now, all the settings are configured well. Only the computers with the IP addresses within 192.168.1.10 ~ 192.168.1.20 can access to Internet. Vigor2925 Series User’s Guide...
Page 133: How To Block Facebook Service Accessed By The Users Via Web Content Filter / Url Content Filter
How to register/activate Web Content Filter (WCF) license? Please visit for getting more information: *How to Register AI/AV/AS/WCF Service (Service Activation Wizard) (http://www.draytek.com/user/SupportFAQDetail.php?ID=1955) *How to Activate Anti-Virus/Anti-Intrusion/Anti-Spam Service (http://www.draytek.com/user/SupportFAQDetail.php?ID=286 ) How to use the Web Content Filter (WCF) (http://www.draytek.com/user/SupportFAQDetail.php?ID=1953) * What the Web Content Filter (WCF) license benefits are, (http://www.draytek.com/user/PdInfoDetail.php?Id=110)
Page 134 Open CSM >> Web Content Filter Profile to create a WCF profile. Check Social Networking with Action, Block. Enable this profile in Firewall>>General Setup>>Default Rule. Vigor2925 Series User’s Guide...
Page 135 Next time when someone accesses facebook via this router, the web page would be blocked and the following message would be displayed instead. A. Block the web page containing the word of “Facebook” Open Object Settings>>Keyword Object. Click an index number to open the setting page.
Page 136 When you finished the above steps, click OK. Then, open Firewall>>General Setup. Click the Default Rule tab. Choose the profile just configured from the drop down list in the field of URL Content Filter. Now, users cannot open any web page with the word “facebook”...
Page 137 Open CSM>>URL Content Filter Profile. Click an index number to open the setting page. Configure the settings as the following figure. When you finished the above steps, please open Firewall>>General Setup. Vigor2925 Series User’s Guide...
Page 138 Click the Default Rule tab. Choose the profile just configured from the drop down list in the field of URL Content Filter. Now, users cannot open any web page with the word “facebook” inside. Vigor2925 Series User’s Guide...
Page 139: How To Setup Address Mapping
Address Mapping is used to map a specified private IP or a range of private IPs of NAT subnet into a specified WAN IP (or WAN IP alias IP). Refer to the following figure. Suppose the WAN settings for a router are configured as follows: WAN1: 202.211.100.10, WAN1 alias: 202.211.100.11 WAN2: 203.98.200.10 Without address mapping feature, when a NAT host with an IP say "192.168.1.10"...
Page 140 Click the Details Page of WAN 1 to open the following page. From the above figure, set main WAN IP address as 202.211.100.10. Click the WAN IP Alias button to configure the other P address which is 202.211.100.11. Make sure Join IP NAT Pool is not checked. Click OK to save the settings. Vigor2925 Series User’s Guide...
Page 141 After finished configuration for WAN1, open Load-Balance/Route Policy. Click Index number 1 and 2 to configure the details. After finished the settings, click OK to save the settings respectively. Vigor2925 Series User’s Guide...
Page 142 Upon completing the above configuration, you have specified the outgoing IP address(es) for some specific computers. Now, you bind some specific computers to some WAN IP alias for outgoing traffic. Vigor2925 Series User’s Guide...
Page 143: How To Setup Load Balance For Packets
The following figure shows a simple application of load balance. WAN1 and WAN2 can be used to access into Internet. The PC in LAN1 can send the data to the remote PC through the specified WAN1. Access into web user interface of Vigor2925series. Open Load-Balance/Route Policy. From the following web page, simply click index number #1.
Page 144 In the following page, check Enable; set Dest IP Start and Dest IP End with 203.65.1.35 and 203.65.1.35; choose WAN1 as the Interface; click default gateway; do not check Auto Failover To The Other WAN. After finished the above settings, click OK to save the configuration. Now, the packets sent to the remote PC (IP address: 203.65.1.35) will be forcefully to pass through WAN1.
Page 145: How To Authenticate Clients Via User Management
Before using the function of User Management, please make sure User-Based has been selected as the Mode in the User Management>>General Setup page. With User Management authentication function, before a valid username and password have been correctly supplied, a particular client will not be allowed to access Internet through the router.
Page 146 Web authentication interface first. Then, the client is trying to access http://www.draytek.com and but brought to the Vigor router. Since this is an SSL connection, some web browsers will display warning messages.
Page 147  With Crome browser, you may get the following warning. Click Proceed anyway. After that, the web authentication window will appear. Input the user name and the password for your account (defined in User Management) and click Login. Vigor2925 Series User’s Guide...
Page 148 If the authentication is successful, the client will be redirected to the original web site that he tried to access. In this example, it is http://www.draytek.com . Furthermore, you will get a popped up window as the following. Then you can access the Internet.
Page 149 With the default setup <body stats=1><script language='javascript'> window.location='http://www.draytek.com'</script></body>, you will be redirected to http://www.draytek.com . You may change it if you want. For example, you will get the following welcome message if you enter Login Successful in the Welcome Message table.
Page 150  Don’t setup a user profile in User Management and a VPN Remote Dial-in user profile with the same Username. Otherwise, you may get unexpected result. It is because the VPN Remote Dial-in User profiles can be extended to the User profiles in User Management for authentication.
Page 151 The LAN clients can also authenticate their accounts via telnet. Telnet to the router’s LAN IP address and input the account name for the authentication: Type the password for authentication and press Enter. The message User login successful will be displayed with the expired time (if configured). Note: Here expired time is “Unlimited”...
Page 152 If the Time Quota is set with “0” minute, you will get the following message which means this account has no time quota. If the Time Quota is enabled and time is not 0 minute, You will get the following message. The expired time is shown after you login. After you run out the available time, you can’t use this account any more until the administrator manually adds additional time for you.
Page 153 The configuration of the VigorPro Alert Notice Tool is as follows: Click Authenticate Now!! to start the authentication immediately. You may get the VigorPro Alert Notice Tool from the following link: http://www.draytek.com/user/SupportDLUtility.php Note:  Any modification to the Firewall policy will break down the connections of all current users.
Page 154: How To Use Dns Filter
The DNS Filter monitors DNS queries on UDP port 53 and will pass the DNS query information to the WCF (web content filter) to help with categorizing HTTPS URL's. Note: For DNS filter must use the WCF service profile to filter the packets, therefore WCF license must be activated first.
Page 155 3. Click OK to save the configuration. 4. A message box will appear. It's a message which reminds that the priority of URL Content Filter is higher than Web Content Filter. Just press OK button to continue. 5. Open CSM>>DNS Filter. Enable the DNS filter; choose Block as the Syslog; choose WCF-1 Default.
Page 156 From the Syslog, we can find out “google” is blocked. Vigor2925 Series User’s Guide...
Page 157: Profile
The administrator can manage the access points linked to Vigor2925. Open External Devices>>Access Point Devices. Vigor2925 will detect the AP connecting to the router automatically and display as below: In this case, a device named with AP800_00507F6EE4980 has been detected by Vigor router.
Page 158 Note: Apply to All APs can automatically apply the settings on Default profile to all of the access points registered to Vigor2925 later. Hence, it is not necessary for you to manually apply wireless profiles for APs respectively. Such feature will be convenient for people who want to quickly deploy multiple Vigor APs in a large exhibition to reach the goal of “plug and play”...
Page 159 The following page is offered for you to modify related settings for 5G SSID of managed AP. Continue to make any changes you want. After finished all of the changes, simply click Finish. Now, the AP (represented with AP800_00507F6EE4980) detected by Vigor router will be applied with the settings modified by Vigor router.
Page 160: Cvm Application - How To Manage The Cpe (Router) Through Vigor2925 Series
To manage CPEs through Vigor2925 series, you have to set URL on CPE first and set username and password for Vigor2925 series. For this section, we use Vigor2860 series as the example. All the CPE configuration will be done through Vigor2925 series. Access into the web user interface of Vigor2925 series.
Page 161 In the end of the CPE (here, Vigor2860 is used), access into the web user interface of the CPE. Open a web browser (for example, IE, Mozilla Firefox or Netscape) and type http://192.168.1.1. Open System Maintenance >> TR-069. In the field of ACS Server, type the URL (IP address with port number) of Vigor2925 series and type the same Username and Password defined on the page of Central VPN Management>>General Setup in Vigor2925 series.
Page 162 Check Allow management from the Internet to set management access control and click OK. Open WAN>>Internet Access. Use the drop down list of Access Mode on WAN1 to select MPoA (RFC1483/2684). Then, click Details Page. Click Specify an IP address. Type correct WAN IP address, subnet mask and gateway IP address for your CPE.
Page 163 Note: Reboot the CPE device and re-log into Vigor2925 series. CPE which has registered to Vigor2925 series will be captured and displayed on the page of Central VPN Management>>CPE Management. Return to the web user interface of Vigor2925 series. Open Central VPN Management>>CPE Management. Now there is one CPE (Vigor2860n+) displayed on the screen.
Page 164: Cvm Application - How To Build The Vpn Between Remote Devices And Vigor2925 Series
When a remote device (e.g., Vigor2860n+ in the following figure) is managed by Vigor2925 series, it is easy to build VPN between these two devices. Access into the web user interface of Vigor2925 series. Open Central VPN Management>>VPN Management. Click the device icon (e.g., Vigor2860n+) to display a drop down list. Then, click the PPTP, IPsec or Advanced.
Page 165 Wait for a moment and click Refresh. If VPN is built successfully, related information will be displayed on CPE VPN Connection List. A LAN to LAN profile for such VPN will be generated automatically. You can access into VPN and Remote Access>>LAN to LAN of the remote device for viewing the detailed information.
Page 166: Cvm Application - How To Upgrade Cpe Firmware Through Vigor2925 Series
Download the newest firmware from your DrayTek website to USB Storage Disk for the device (e.g., Vigor2860) managed by Vigor2925 series. Vigor2860, as an example, is chosen for Vigor2925 to perform the CPE firmware upgrade remotely in this case. Plug in USB storage disk onto Vigor2925 series via USB interface. Make sure the USB disk has been installed correctly;...
Page 167 The Maintenance profile dialog appears. In the field of Profile Name, type a name for such maintenance profile; check Enable; and choose the one you want to perform firmware upgrade from Device Name drop down list. From the Action Type, choose Firmware Upgrade. Type the file/path of the newest firmware or click Select to locate it.
Page 168 Then check the device information for the managed device if the firmware upgrade is successful or not. Click Managed Devices List. Click the icon of Vigor2860 and click Edit and view the software version. Another way to check if the firmware upgrade is completed or not, simply open Central VPN Management>>Log &...
Page 169: Advanced Configuration
This chapter will guide users to execute advanced (full) configuration through admin mode operation. Open a web browser on your PC and type http://192.168.1.1. The window will ask for typing username and password. Please type “admin/admin” on Username/Password for administration operation. Now, the Main Screen will appear.
Page 170 From 10.0.0.0 to 10.255.255.255 From 172.16.0.0 to 172.31.255.255 From 192.168.0.0 to 192.168.255.255 As the router plays a role to manage and further protect its LAN, it interconnects groups of host PCs. Each of them has a private IP address assigned by the built-in DHCP server of the Vigor router.
Page 171: General Setup
Therefore, when WAN1 and WAN2 are not available, the router will use 3.5G for supporting automatically. The supported 3G/4G USB Modem will be listed on DrayTek web site. Please visit www.draytek.com for more detailed information. Below shows the menu items for WAN.
Page 172 Index Click the WAN interface link under Index to access into the WAN configuration page. Enable V means such WAN interface is enabled and ready to be used. Display the physical mode and physical type of such WAN Physical Mode / Type interface.
Page 173 Auto negotiation for determined by the system. Line Speed If your choose According to Line Speed as the Load Balance Mode, please type the line speed for downloading and uploading for such WAN interface. The unit is kbps. VLAN Tag insertion Enable –...
Page 174 To use 3G/4G network connection through 3G/4G USB Modem, please configure WAN3 or WAN4 interface. Available settings are explained as follows: Item Description Enable Choose Yes to invoke the settings for this WAN interface. Choose No to disable the settings for this WAN interface. Display Name Type the description for such WAN interface.
Page 175: Internet Access
When any of selected WAN disconnect – Such backup WAN will be activated when any master WAN interface disconnects. When all of selected WAN disconnect – Such backup WAN will be activated only when all master WAN interfaces disconnect. After finished the above settings, click OK to save the settings. For the router supports multi-WAN function, the users can set different WAN settings (for WAN1/WAN2/WAN3/WAN4) for Internet Access.
Page 176 Physical Mode It shows the physical connection for WAN1/WAN2 (Ethernet) /WAN3/WAN4 (USB) according to the real network connection. Access Mode Use the drop down list to choose a proper access mode. Then, click Details Page for accessing the settings page to configure the settings.
Page 177 be stored. Data – Type the content of the data to be processed by the function of DHCP option. To use PPPoE as the accessing protocol of the internet, please click the PPPoE tab. The following web page will be shown. Available settings are explained as follows: Item Description...
Page 178 WAN Connection Such function allows you to verify whether network Detection connection is alive or not through ARP Detect or Ping Detect. Mode – Choose ARP Detect or Ping Detect for the system to execute for WAN detection. Ping IP – If you choose Ping Detect as detection mode, you have to type IP address in this field for pinging.
Page 179 Specify a MAC Address – Type the MAC address for the router manually. After finishing all the settings here, please click OK to activate them. For static IP mode, you usually receive a fixed public IP address or a public subnet, namely multiple public IP addresses from your DSL or Cable ISP service providers.
Page 180 specify the IP address for the system to PING it for keeping alive. PING Interval - Enter the interval for the system to execute the PING operation. WAN Connection Such function allows you to verify whether network Detection connection is alive or not through ARP Detect or Ping Detect.
Page 181 you have assigned. DHCP Client Identifier for some ISP  Enable: Check the box to specify username and password as the DHCP client identifier for some ISP.  Username: Type a name as username. The maximum length of the user name you can set is 63 characters.
Page 182 Available settings are explained as follows: Item Description PPTP/L2TP Enable PPTP- Click this radio button to enable a PPTP client to establish a tunnel to a DSL modem on the WAN interface. Enable L2TP - Click this radio button to enable a L2TP client to establish a tunnel to a DSL modem on the WAN interface.
Page 183 Idle Timeout - Set the timeout for breaking down the Internet after passing through the time without any action. IP Address Assignment WAN IP Alias - If you have multiple public IP addresses Method(IPCP) and would like to utilize them on the WAN interface, please use WAN IP Alias.
Page 184 To use 3G/4G USB Modem (PPP mode) as the accessing protocol of the internet, please choose Internet Access from WAN menu. Then, select 3G/4G USB Modem (PPP mode) for WAN3. The following web page will be shown. Available settings are explained as follows: Item Description Modem Support List...
Page 185 Modem Initial String Such value is used to initialize USB modem. Please use the default value. If you have any question, please contact to your ISP. The maximum length of the string you can set is 47 characters. APN Name APN means Access Point Name which is provided and required by some ISPs.
Page 186 To use 4G USB Modem (DHCP mode) as the accessing protocol of the internet, please choose Internet Access from WAN menu. Then, select 4G USB Modem (DHCP mode) for WAN3/WAN4. The following web page will be shown. Available settings are explained as follows: Item Description Modem Support List...
Page 187 It means Max Transmit Unit for packet. The default setting is 1380. WAN Connection Such function allows you to verify whether network Detection connection is alive or not through ARP Detect or Ping Detect. Mode – Choose ARP Detect or Ping Detect for the system to execute for WAN detection.
Page 188 Note: At present, the IPv6 prefix can be acquired via the PPPoE mode connection which is available for the areas such as Taiwan (hinet), the Netherlands, Australia and UK. – – Tunnel setup protocol client (TSPC) is an application which could help you to connect to IPv6 network easily.
Page 189 Item Description Username Type the name obtained from the broker. It is suggested for you to apply another username and password for http://gogonet.gogo6.com/page/freenet6-account. The maximum length of the name you can set is 63 characters. Password Type the password assigned with the user name. The maximum length of the name you can set is 19 characters.
Page 190 Confirm Password Type the password again to make the confirmation. Tunnel Broker Type the address for the tunnel broker IP, FQDN or an optional port number. Type the subnet prefix address getting from service Subnet Prefix provider. The maximum length of the prefix you can set is 128 characters.
Page 191 – – This type allows you to setup static IPv6 address for WAN interface. Available settings are explained as follows: Item Description Static IPv6 Address IPv6 Address – Type the IPv6 Static IP Address. configuration Prefix Length – Type the fixed value for prefix length. Add –...
Page 192 – – This type allows you to setup 6in4 Static Tunnel for WAN interface. Such mode allows the router to access IPv6 network through IPv4 network. However, 6in4 offers a prefix outside of 2002::0/16. So, you can use a fixed endpoint rather than any cast endpoint.
Page 193 Below shows an example for successful IPv6 connection based on 6in4 Static Tunnel mode. – – This type allows you to setup 6rd for WAN interface. Available settings are explained as follows: Item Description 6rd Mode Auto 6rd – Retrieve 6rd prefix automatically from 6rd service provider.
Page 194 6rd Prefix Type the 6rd IPv6 address. 6rd Prefix Length Type the IPv6 prefix length for the 6rd IPv6 prefix in number of bits. After finished the above settings, click OK to save the settings. Below shows an example for successful IPv6 connection based on 6rd mode. Vigor2925 Series User’s Guide...
Page 195: Multi-Vlan
Multi-VLAN allows users to create profiles for specific WAN interface and bridge connections for user applications that require very high network throughput. Simply go to WAN and select Multi-VLAN. This page shows the basic configurations used by every channel. Available settings are explained as follows: Item Description Channel...
Page 196 Available settings are explained as follows: Item Description Multi-VLAN Channel Enable – Click it to enable the configuration of this 8/9/10 channel. Disable –Click it to disable the configuration of this channel. WAN Type The connections and interfaces created in every channel may select a specific WAN type to be built upon.
Page 197 please contact with your ISP and then click WAN link of Channel 5, 6 or 7 to configure your router. Available settings are explained as follows: Item Description Multi-VLAN Channel Enable – Click it to enable the configuration of this 5/6/7 channel.
Page 198 General Settings VLAN Tag – Type the value as the VLAN ID number. Valid settings are in the range from 1 to 4095. The network traffic flowing on each channel will be identified by the system via their VLAN Tags. Channels using the same WAN type may not configure the same VLAN tag value.
Page 199: Wan Budget
This function is used to determine the data traffic volume for each WAN interface respectively to prevent from overcharges for data transmission by the ISP. Please note that the Quota Limit and Billing cycle day of month settings will need to be configured correctly first in order for some period calculations to be performed correctly.
Page 200: Wan Budget
out a warning message to the administrator when the quota is running out. However, the connection charges will be calculated continuously. Send SMS messages to Administrator - The system will send out SMS message to the administrator when the quota is running out.
Page 201 The monitor page displays the status WAN budget, including the duration and the usage. If the WAN budget is exhausted, a lock will be displayed on the page if Shutdown WAN interface is selected. Which means no data transmission will be carried out. Moreover, the system will send out a warning message to the administrator if Send Mail Alert to Administrator is selected.
Page 202: Lan
Local Area Network (LAN) is a group of subnets regulated and ruled by router. The design of network structure is related to what type of public IP addresses coming from your ISP. The most generic function of Vigor router is NAT. It creates a private subnet of your own. As mentioned previously, the router will talk to other public hosts on the Internet by using public IP address and talking to local hosts by using its private IP address.
Page 203 Vigor router will exchange routing information with neighboring routers using the RIP to accomplish IP routing. This allows users to change the information of the router such as IP address and the routers will automatically inform for each other. When you have several subnets in your LAN, sometimes a more effective and quicker way for connection is the Static routes function rather than other method.
Page 204: General Setup
This page provides you the general settings for LAN. Click LAN to open the LAN settings page and choose General Setup. There are four subnets provided by the router which allow users to divide groups into different subnets (LAN1 – LAN5). In addition, different subnets can link for each other by configuring Inter-LAN Routing.
Page 205 General Setup Allow to configure settings for each subnet respectively. Index - Display all of the LAN items. Status- Basically, LAN1 status is enabled in default. LAN2 –LAN5 and IP Routed Subnet can be observed by checking the box of Status. DHCP- LAN1 is configured with DHCP in default.
Page 206 Force router to use DNS Force Vigor router to use DNS servers configured in server IP address ….. LAN1/LAN2/LAN3/LAN4/LAN5 instead of DNS servers given by the Internet Access server (PPPoE, PPTP, L2TP or DHCP server). Inter-LAN Routing Check the box to link two or more different subnets (LAN and LAN).
Page 207 – – There are two configuration pages for LAN1, Ethernet TCP/IP and DHCP Setup (based on IPv4) and IPv6 Setup. Click the tab for each type and refer to the following explanations for detailed information. Available settings are explained as follows: Item Description Network Configuration...
Page 208 DHCP Server IP Address – It is available when Enable Relay Agent is checked. Set the IP address of the DHCP server you are going to use so the Relay Agent can help to forward the DHCP request to the DHCP server. Start IP Address - Enter a value of the IP address pool for the DHCP server to start with when issuing IP addresses.
Page 209 If both the Primary IP and Secondary IP Address fields are left empty, the router will assign its own IP address to local users as a DNS proxy server and maintain a DNS cache. If the IP address of a domain name is already in the DNS cache, the router will resolve the domain name immediately.
Page 210 Item Description Router Advertisement Enable – Click it to enable router advertisement server. The Server router advertisement daemon sends Router Advertisement messages, specified by RFC 2461, to a local Ethernet LAN periodically and when requested by a node sending a Router Solicitation message.
Page 211 LAN2 ~LAN5 are available only when LAN>>VLAN is enabled. In which, the options of For NAT Usage and For Routing Usage will be suitable for more flexible applications, e.g., MPLS (Multiprotocol Label Switching). Available settings are explained as follows: Item Description Network Configuration Enable/Disable - Click Enable to enable such...
Page 212 Relay Agent is checked. Set the IP address of the DHCP server you are going to use so the Relay Agent can help to forward the DHCP request to the DHCP server. Start IP Address - Enter a value of the IP address pool for the DHCP server to start with when issuing IP addresses.
Page 213 If both the Primary IP and Secondary IP Address fields are left empty, the router will assign its own IP address to local users as a DNS proxy server and maintain a DNS cache. If the IP address of a domain name is already in the DNS cache, the router will resolve the domain name immediately.
Page 214 Open LAN>>VLAN. Check the Enable box to enable VLAN configuration. Type the settings as follows and click OK to save the settings. Return to LAN>>General Setup. Now, LAN2 is available for configuration. Click the Details Page button of LAN2. Choose For Routing Usage. Type the settings as follows and click OK to save the settings.
Page 215 Now, a network connection via MPLS (Multiprotocol Label Switching) between LAN2 user and the Branch user is established successfully. Internet is not required for them. Vigor2925 Series User’s Guide...
Page 216 Available settings are explained as follows: Item Description Network Configuration Enable/Disable - Click Enable to enable such configuration; click Disable to disable such configuration. For Routing Usage, IP Address - Type in private IP address for connecting to a local private network (Default: 192.168.1.1). Subnet Mask - Type in an address code that determines the size of the network.
Page 217 192.168.1.254. IP Pool Counts - Enter the maximum number of PCs that you want the DHCP server to assign IP addresses to. The default is 50 and the maximum is 253. Lease Time - Enter the time to determine how long the IP address assigned by DHCP server can be used.
Page 218: Static Route
Go to LAN to open setting page and choose Static Route. The router offers IPv4 and IPv6 for you to configure the static route. Both protocols bring different web pages. Available settings are explained as follows: Item Description Set to Factory Default Clear all of the settings and return to factory default settings.
Page 219 Click any underline of index number to get the following page. Available settings are explained as follows: Item Description Enable Check it to enable this profile. Destination IP Address Type an IP address as the destination of such static route. Subnet Mask Type the subnet mask for such static route.
Page 220 You can set up to 40 profiles for IPv6 static route. Click the IPv6 tab to open the following page: Each item is explained as follows: Item Description Set to Factory Default Clear all of the settings and return to factory default settings.
Page 221 Destination IPv6 Address Type the IP address with the prefix length for this entry. / Prefix Len Gateway IPv6 Address Type the gateway address for this entry. Use the drop down list to specify an interface for this static Network Interface route.
Page 222 Go to LAN page and click General Setup, select 1st Subnet as the RIP Protocol Control. Then click the OK button. Note: There are two reasons that we have to apply RIP Protocol Control on 1st Subnet. The first is that the LAN interface can exchange RIP packets with the neighboring routers via the 1st subnet (192.168.1.0/24).
Page 223: Vlan
Go to Diagnostics and choose Routing Table to verify current routing table. With the 5-port Gigabit switch on the LAN side, Vigor router provides extremely high speed connectivity for the highest speed local data transfer of any server or local PCs. On the wireless-equipped model, each of the wireless SSIDs can also be grouped within one of the VLANs.
Page 224 Note: Settings in this page only applied to LAN port but not WAN port. Available settings are explained as follows: Item Description Enable Click it to enable VLAN configuration. P1 – P5 – Check the LAN port(s) to be grouped under the selected VLAN.
Page 225 Enable – Check the box to enable the function of VLAN VLAN Tag with tag. The router will add specific VLAN number to all packets on the LAN while sending them out. Please type the tag value and specify the priority for the packets sending by LAN.
Page 226 After checking the box to enable VLAN function, you will check the table according to the needs as shown below. Click OK to save the settings. The Vigor router also supports up to six private IP subnets on the LAN. Each can be independent (isolated) or common (able to communicate with each other).
Page 227: Bind Ip To Mac
This function is used to bind the IP and MAC address in LAN to have a strengthening control in network. When this function is enabled, all the assigned IP and MAC address binding together cannot be changed. If you modified the binding IP or MAC address, it might cause you not access into the Internet.
Page 228 Refresh Refresh the ARP table listed below to obtain the newest ARP table information. IP Address – Type the IP address that will be used for the Add or Update specified MAC address. Mac Address – Type the MAC address that is used to bind with the assigned IP address.
Page 229: Lan Port Mirror
LAN port mirror can be applied for the users in LAN. Generally speaking, this function copies traffic from one or more specific ports to a target port. This mechanism helps manager track the network errors or abnormal packets transmission without interrupting the flow of data access the network.
Page 230: Wired 802.1X
IEEE 802.1x is an IEEE Standard for port-based Network Access Control (PNAC). It is part of the IEEE 802.1 group of networking protocols. It provides an authentication mechanism for the device that is attached to a LAN or WLAN. Wired 802.1x provides authentication for one network device on each LAN port. The RADIUS Server settings must be configured before enabling 802.1x because the EAP (Extensible Authentication Protocol) Authenticator relies on the RADIUS Server in its authentication process.
Page 231: Web Portal Setup
This page allows you to configure a profile with specified URL for accessing into or display a message when a wireless/LAN user connects to Internet through this router. No matter what the purpose of the wireless/LAN client is, he/she will be forced into the URL configured here while trying to access into the Internet or the desired web page through this router.
Page 232: Load-Balance /Route Policy
Available settings are explained as follows: Item Description Disable Click this button to close this function. URL Redirect Any user who wants to access into Internet through this router will be redirected to the URL specified here first. It is a useful method for the purpose of advertisement.
Page 233 (Failback), the packets will be returned to it immediately.  Other routing. Specify routing policy to determine the direction of the data transmission. Note: For more detailed information about using policy route, refer to Support >>FAQ/Application Notes on www.draytek.com. Available settings are explained as follows: Item Description Index Click the number of index to access into the configuration web page.
Page 234 Dest IP End Display the IP address for the end of the destination IP. Dest Port Start Display the IP address for the start of the destination port. Dest Port End Display the IP address for the end of the destination port. Move UP/Move Down Use Up or Down link to move the order of the policy.
Page 235 Available settings are explained as follows: Item Description Interface Use the drop down list to choose a WAN or LAN interface or VPN profile. Packets match with the above criteria will be transferred to the interface chosen here. 4. After specifying the interface, click Next to get the following page. Available settings are explained as follows: Item Description...
Page 236 5. After choosing the mechanism, click Next to get the summary page for reference. 6. If there is no error, click Finish to complete wizard setting. To use Advance Mode, do the following steps: 1. Click the Advance Mode radio button. 2.
Page 237 Available settings are explained as follows: Item Description Enable Check this box to enable this policy. Use the drop-down menu to choose a proper protocol for Protocol the WAN interface. Source IP Any – Any IP can be treated as the source IP. Src IP Start - Type the source IP start for the specified WAN interface.
Page 238 destination IPs will be passed through the WAN interface. Destination Port Any – Any port number can be treated as the destination port. Dest Port Start - Type the destination port start for the destination IP. Dest Port End - Type the destination port end for the destination IP.
Page 239 When you finish the configuration, please click OK to save and exit this page. Vigor2925 Series User’s Guide...
Page 240 Note: The web user interface will be revised later. Example 1: In the following figure, a LAN to LAN VPN tunnel is built between DrayTek VPN router (e.g., Vigor2925 series) and the remote router. Firewall Router can receive all of the traffic coming from remote PC which wants to access into Internet;...
Page 241 Click any Index number link (e.g., 1 in this case). Configure the settings as follows. Now, if you want such route policy will be applied by Vigor router with higher priority, please adjust the value of Priority for such route policy. In general, default route is specified with the lowest priority for it value is fixed as “250”.
Page 242 Example 2: Below shows a scenario that local users behind Vigor router A want to access into a remote service (e.g., YouTube) which is blocked or restricted by local Service Provider in their country (e.g., UK in this case). A policy route can be created by the side of Router A to break through the Internet censorship circumvention.
Page 243 Click OK to save the settings. Vigor2925 Series User’s Guide...
Page 244: Nat
Usually, the router serves as an NAT (Network Address Translation) router. NAT is a mechanism that one or more private IP addresses can be mapped into a single public one. Public IP address is usually assigned by your ISP, for which you may get charged. Private IP addresses are recognized only among internal hosts.
Page 245: Port Redirection
Below shows the menu items for NAT. Port Redirection is usually set up for server related service inside the local network (LAN), such as web servers, FTP servers, E-mail servers etc. Most of the case, you need a public IP address for each server and this public IP address/domain name are recognized by all users.
Page 246 Each item is explained as follows: Item Description Index Display the number of the profile. Service Name Display the description of the specific network service. WAN Interface Display the WAN IP address used by the profile. Protocol Display the transport layer protocol (TCP or UDP). Public Port Display the port number which will be redirected to the specified Private IP and Port of the internal host.
Page 247 Item Description Enable Check this box to enable such port redirection setting. Mode Two options (Single and Range) are provided here for you to choose. To set a range for the specific service, select Range. In Range mode, if the public port (start port and end port) and the starting IP of private IP had been entered, the system will calculate and display the ending IP of private IP automatically.
Page 248: Dmz Host
As mentioned above, Port Redirection can redirect incoming TCP/UDP or other traffic on particular ports to the specific private IP address/port of host in the LAN. However, other IP protocols, for example Protocols 50 (ESP) and 51 (AH), do not travel on a fixed port. Vigor router provides a facility DMZ Host that maps ALL unsolicited data on any protocol to a single host in the LAN.
Page 249 The security properties of NAT are somewhat bypassed if you set up DMZ host. We suggest you to add additional filter rules or a secondary firewall. Click DMZ Host to open the following page. You can set different DMZ host for each WAN interface.
Page 250 DMZ Host for WAN2~ WAN4 is slightly different with WAN1. Active True IP selection is available for WAN1 only. See the following figure. Vigor2925 Series User’s Guide...
Page 251 If you previously have set up WAN Alias for PPPoE or Static or Dynamic IP mode in WAN2 interface, you will find them in Aux. WAN IP for your selection. Available settings are explained as follows: Item Description Enable Check to enable the DMZ Host function. Enter the private IP address of the DMZ host, or click Private IP Choose PC to select one.
Page 252: Open Ports
Open Ports allows you to open a range of ports for the traffic of special applications. Common application of Open Ports includes P2P application (e.g., BT, KaZaA, Gnutella, WinMX, eMule and others), Internet Camera etc. Ensure that you keep the application involved up-to-date to avoid falling victim to any security exploits.
Page 253 Available settings are explained as follows: Item Description Check to enable this entry. Enable Open Ports Comment Make a name for the defined network application/service. WAN Interface Specify the WAN interface that will be used for this entry. WAN IP Specify the WAN IP address that will be used for this entry.
Page 254: Port Triggering
After finishing all the settings here, please click OK to save the configuration. Port Triggering is a variation of open ports function. The key difference between "open port" and "port triggering" is:  Once the OK button is clicked and the configuration has taken effect, "open port" keeps the ports opened forever.
Page 255 Comment Display the text which memorizes the application of this rule. Triggering Protocol Display the protocol of the triggering packets. Display the port of the triggering packets. Triggering Port Incoming Protocol Display the protocol for the incoming data of such triggering profile.
Page 256 Type the port or port range for such triggering profile. Triggering Port Incoming Protocol When the triggering packets received, it is expected the incoming packets will use the selected protocol. Select the protocol (TCP, UDP or TCP/UDP) for the incoming data of such triggering profile.
Page 257: Hardware Acceleration
Hardware Acceleration is also called PPA in DrayTek for it is based on Protocol Processing Engine (PPE) of Infinion. It can only support 128 sessions for network traffic (IN & OUT) with implementing three kinds of modes - Disable, Auto and Manual.
Page 258 available in Auto Mode, too. But the UDP protocol is only supported in this sub-item. Apply the Class Rule in Quality of Service – Users can apply the information provided by QoS in this sub-item. Note: Please visit our website for referring the detailed configuration of QoS.
Page 259: Firewall
While the broadband users demand more bandwidth for multimedia, interactive applications, or distance learning, security has been always the most concerned. The firewall of the Vigor router helps to protect your local network against attack from unauthorized outsiders. It also restricts users in the local network from accessing the Internet.
Page 260 Stateful inspection is a firewall architecture that works at the network layer. Unlike legacy static packet filtering, which examines a packet based on the information in its header, stateful inspection builds up a state machine to track each connection traversing all interfaces of the firewall and makes sure they are valid.
Page 261: General Setup
General Setup allows you to adjust settings of IP Filter and common options. Here you can enable or disable the Call Filter or Data Filter. Under some circumstance, your filter set can be linked to work in a serial manner. So here you assign the Start Filter Set only. Also you can configure the Log Flag settings, Apply IP filter to VPN incoming packets, and Accept incoming fragmented UDP packets.
Page 262 Accept large incoming… Some on-line games (for example: Half Life) will use lots of fragmented UDP packets to transfer game data. Instinctively as a secure firewall, Vigor router will reject these fragmented packets to prevent attack unless you enable “Accept large incoming fragmented UDP or ICMP Packets”.
Page 263 Such page allows you to choose filtering profiles including QoS, Load-Balance Policy, User Management, APP Enforcement, URL Content Filter and Web Content Filter for data transmission via Vigor router. Available settings are explained as follows: Item Description Filter Select Pass or Block for the packets that do not match with the filter rules.
Page 264 User Management Such item is available only when Rule-Based is selected in User Management>>General Setup. The general firewall rule will be applied to the user/user group/all users specified here. Note: When there is no user profile or group profile existed, Create New User or Create New Group item will appear for you to click to create a new one.
Page 265 at least one profile in CSM>> Web Content Filter web page first. Or click the DNS Filter link in this page to create a new profile. Advance Setting Click Edit to open the following window. However, it is strongly recommended to use the default settings here. Codepage - This function is used to compare the characters among different languages.
Page 266: Filter Setup
Click Firewall and click Filter Setup to open the setup page. To edit or add a filter, click on the set number to edit the individual set. The following page will be shown. Each filter set contains up to 7 rules. Click on the rule number button to edit each rule.
Page 267 Available settings are explained as follows: Item Description Check to enable the Filter Check this box to enable the filter rule. Rule Comments Enter filter set comments/description. Maximum length is 14- character long. Index(1-15) Set PCs on LAN to work at certain time interval only. You may choose up to 4 schedules out of the 15 schedules pre-defined in Applications >>...
Page 268 Note: RT means routing domain for 2nd subnet or other LAN. Source/Destination IP Click Edit to access into the following dialog to choose the source/destination IP or IP ranges. To set the IP address manually, please choose Any Address/Single Address/Range Address/Subnet Address as the Address Type and type them in this dialog.
Page 269 To set the service type manually, please choose User defined as the Service Type and type them in this dialog. In addition, if you want to use the service type from defined groups or objects, please choose Group and Objects as the Service Type.
Page 270 passed immediately. Block If No Further Match - A packet matching the rule, and that does not match further rules, will be dropped. Pass If No Further Match - A packet matching the rule, and that does not match further rules, will be passed through.
Page 271 troubleshooting needs, you can specify to record information for IM/P2P by checking the Log box. It will be sent to Syslog server. Please refer to section Syslog/Mail Alert for more detailed information. URL Content Filter Select one of the URL Content Filter profile settings (created in CSM>>...
Page 272 TCP protocol only; session timeout is configured for the data flow which matched with the firewall rule. DrayTek Banner – Please uncheck this box and the following screen will not be shown for the unreachable web page. The default setting is Enabled.
Page 273 Strict Security Checking - For the sake of security, you might want the router executing strict security checking for data transmission. The router performance will be affected if you invoke strict security checking. APP Enforcement – Check this box to execute the critical checking for all the files transferred via IM/P2P.
Page 274 As stated before, all the traffic will be separated and arbitrated using on of two IP filters: call filter or data filter. You may preset 12 call filters and data filters in Filter Setup and even link them in a serial manner. Each filter set is composed by 7 filter rules, which can be further defined.
Page 275: Dos Defense
As a sub-functionality of IP Filter/Firewall, there are 15 types of detect/ defense function in the DoS Defense setup. The DoS Defense functionality is disabled for default. Click Firewall and click DoS Defense to open the setup page. Available settings are explained as follows: Item Description Enable Dos Defense...
Page 276 will start to randomly discard the subsequent UDP packets for a period defined in Timeout. The default setting for threshold and timeout are 2000 packets per second and 10 seconds, respectively. That means, when 2000 packets per second received, they will be regarded as “attack event”...
Page 277 Any broadcast UDP packets received from the Internet is blocked. Activating the DoS/DDoS defense functionality might block some legal packets. For example, when you activate the fraggle attack defense, all broadcast UDP packets coming from the Internet are blocked. Therefore, the RIP packets from the Internet might be dropped.
Page 278 After finishing all the settings here, please click OK to save the configuration. Vigor2925 Series User’s Guide...
Page 279: User Management
User Management is a security feature which disallows any IP traffic (except DHCP-related packets) from a particular host until that host has correctly supplied a valid username and password. Instead of managing with IP address/MAC address, User Management function manages hosts with user account. Network administrator can give different firewall policies or rules for different hosts with different User Management accounts.
Page 280: General Setup
General Setup can determine the standard (rule-based or user-based) for the users controlled by User Management. The mode (standard) selected here will influence the contents of the filter rule(s) applied to every user. Available settings are explained as follows: Item Description Mode There are two modes offered here for you to choose.
Page 281: User Profile
This page allows you to set customized profiles (up to 200) which will be applied for users controlled under User Management. Simply open User Management>>User Profile. To set the user profile, please click any index number link to open the following page. Notice that profile 1 (admin) and profile 2 (Dial-In User) are factory default settings.
Page 282 Available settings are explained as follows: Item Description Enable this account Check this box to enable such user profile. Username Type a name for such user profile (e.g., LAN_User_Group_1, WLAN_User_Group_A, WLAN_User_Group_B, etc). When a user tries to access Internet through this router, an authentication step must be performed first.
Page 283 For the detailed configuration, simply refer to Firewall>>Filter Rule. The firewall filter rules that are not selected in Firewall>>General>>Default rule can be available for use in User Management>>User Profile. External Service The router will authenticate the dial-in user by itself or by Authentication external service such as LDAP server or Radius server or TACACS+ server.
Page 284 Next, the user can access Internet through any browser on Windows. Note that Alert Tool can be downloaded from DrayTek web site. Telnet – If it is selected, the user can use Telnet command to perform the authentication job.
Page 285: User Group
– Click this box to set and increase the data quota for such profile. – Click this box to decrease the data quota for such profile. Reset quota to default Set default time quota and data quota for such profile. When when scheduling time the scheduling time is up, the router will use the default quota expired...
Page 286: User Online Status
Available settings are explained as follows: Item Description Name Type a name for this user group. Available User Objects You can gather user profiles (objects) from User Profile page within one user group. All the available user objects that you have created will be shown in this box. Notice that user object, Admin and Dial-In User are factory settings.
Page 287: Objects Settings
Available settings are explained as follows: Item Description Refresh Seconds Use the drop down list to choose the time interval of the page refresh. Refresh Click this link to refresh this page manually. Index Display the number of the user online. User Display the users which connect to Vigor router currently.
Page 288: Ip Object
You can set up to 192 sets of IP Objects with different conditions. Available settings are explained as follows: Item Description Set to Factory Default Clear all profiles. Index Display the profile number that you can configure. Name Display the name of the object profile. To set a new profile, please do the steps listed below: 1.
Page 289 Available settings are explained as follows: Item Description Name Type a name for this profile. Maximum 15 characters are allowed. Interface Choose a proper interface. For example, the Direction setting in Edit Filter Rule will ask you specify IP or IP range for WAN or LAN/DMZ/RT/VPN or any IP address.
Page 290 After finishing all the settings here, please click OK to save the configuration. Below is an example of IP objects settings. Vigor2925 Series User’s Guide...
Page 291: Ip Group
This page allows you to bind several IP objects into one IP group. Available settings are explained as follows: Item Description Clear all profiles. Set to Factory Default Index Display the profile number that you can configure. Name Display the name of the group profile. To set a new profile, please do the steps listed below: 1.
Page 292: Ipv6 Object
Available settings are explained as follows: Item Description Name Type a name for this profile. Maximum 15 characters are allowed. Interface Choose WAN, LAN or Any to display all the available IP objects with the specified interface. All the available IP objects with the specified interface Available IP Objects chosen above will be shown in this box.
Page 293 To set a new profile, please do the steps listed below: 1. Click the number (e.g., #1) under Index column for configuration in details. 2. The configuration page will be shown as follows: Available settings are explained as follows: Item Description Name Type a name for this profile.
Page 294: Ipv6 Group
After finishing all the settings, please click OK to save the configuration. This page allows you to bind several IPv6 objects into one IPv6 group. Available settings are explained as follows: Item Description Set to Factory Default Clear all profiles. Index Display the profile number that you can configure.
Page 295: Service Type Object
Available settings are explained as follows: Item Description Name Type a name for this profile. Maximum 15 characters are allowed. Available IPv6 All the available IPv6 objects with the specified interface Objects chosen above will be shown in this box. Selected IPv6 Objects Click >>...
Page 296 2. The configuration page will be shown as follows: Available settings are explained as follows: Item Description Name Type a name for this profile. Protocol Specify the protocol(s) which this profile will apply to. Source/Destination Source Port and the Destination Port column are available Port for TCP/UDP protocol.
Page 297: Service Type Group
This page allows you to bind several service types into one group. Available settings are explained as follows: Item Description Set to Factory Default Clear all profiles. Index Display the profile number that you can configure. Name Display the name of the group profile. To set a new profile, please do the steps listed below: 1.
Page 298: Keyword Object
Item Description Name Type a name for this profile. Available Service All the available service objects that you have added on Objects Setting>>Service Type Object will be shown in Type Objects this box. Selected Service Type Click >> button to add the selected IP objects in this box. Objects After finishing all the settings, please click OK to save the configuration.
Page 299 To set a new profile, please do the steps listed below: 1. Click the number (e.g., #1) under Index column for configuration in details. 2. The configuration page will be shown as follows: Available settings are explained as follows: Item Description Name Type a name for this profile, e.g., game.
Page 300: Keyword Group
This page allows you to bind several keyword objects into one group. The keyword groups set here will be chosen as black /white list in CSM >>URL /Web Content Filter Profile. Available settings are explained as follows: Item Description Set to Factory Default Clear all profiles.
Page 301: File Extension Object
Available settings are explained as follows: Item Description Name Type a name for this group. Maximum 15 characters are allowed. Available Keyword You can gather keyword objects from Keyword Object Objects page within one keyword group. All the available Keyword objects that you have created will be shown in this box.
Page 302 To set a new profile, please do the steps listed below: 1. Click the number (e.g., #1) under Profile column for configuration in details. 2. The configuration page will be shown as follows: Available settings are explained as follows: Item Description Profile Name Type a name for this profile.
Page 303: Sms/Mail Service Object
This page allows you to set ten profiles which will be applied in Application>>SMS/Mail Alert Service. Each item is explained as follows: Item Description Set to Factory Default Clear all of the settings and return to factory default settings. Index Display the profile number that you can configure.
Page 304 2. The configuration page will be shown as follows: Available settings are explained as follows: Item Description Type a name for such SMS profile. The maximum length of Profile Name the name you can set is 31 characters. Service Provider Use the drop down list to specify the service provider which offers SMS service.
Page 305 Vigor router offers several SMS service provider to offer the SMS service. However, if your service provider cannot be found from the service provider list, simply use Index 9 and Index 10 to make customized SMS service. The profile name for Index 9 and Index 10 are fixed. You can click the number (e.g., #9) under Index column for configuration in details.
Page 306 Username Type a user name that the sender can use to register to selected SMS provider. The maximum length of the name you can set is 31 characters. Password Type a password that the sender can use to register to selected SMS provider.
Page 307 To set a new profile, please do the steps listed below: 1. Click the Mail Server tab, and click the number (e.g., #1) under Index column for configuration in details. 2. The configuration page will be shown as follows: Available settings are explained as follows: Item Description Profile Name...
Page 308: Notification Object
Authentication The mail server must be authenticated with the correct username and password to have the right of sending message out. Check the box to enable the function. Username – Type a name for authentication. The maximum length of the name you can set is 31 characters. Password –...
Page 309 To set a new profile, please do the steps listed below: 1. Open Object Setting>>Notification Object, and click the number (e.g., #1) under Index column for configuration in details. 2. The configuration page will be shown as follows: Available settings are explained as follows: Item Description Profile Name...
Page 310: Csm Profile
CSM is an abbreviation of Content Security Management which is used to control IM/P2P usage, filter the web content and URL content to reach a goal of security management. As the popularity of all kinds of instant messenger application arises, communication cannot become much easier.
Page 311: App Enforcement Profile
You can define policy profiles for IM (Instant Messenger)/P2P (Peer to Peer)/Protocol/Misc application. This page allows you to set 32 profiles for different requirements. The APP Enforcement Profile will be applied in Default Rule of Firewall>>General Setup for filtering. Available settings are explained as follows: Item Description Set to Factory Default...
Page 312 Below shows the items with versions which are categorized under IM Available settings are explained as follows: Item Description Profile Name Type a name for the CSM profile. The maximum length of the name you can set is 15 characters. Select All Click it to choose all of the items in this page.
Page 313 The items categorized under P2P ----- Vigor2925 Series User’s Guide...
Page 314 The items categorized under Others ----- Vigor2925 Series User’s Guide...
Page 315: Appe Signature Upgrade
The APPE Enforcement Profile adopted by Vigor router will be treated as the APPE signature. DrayTek will periodically upgrade versions for all of the APPs supported by Vigor router. However, it might be inconvenient for users to upgrade the APP version one by one. This feature is specially designed to offer a quick method to execute APP version upgrade.
Page 316 Then, click Upgrade and wait for the system completing the process. Upgrade Automatically Scheduled Update - Check the box to make Vigor router upgrading the APPE signature based on the schedule configured here. After finishing all the settings, please click OK to save the configuration. Vigor2925 Series User’s Guide...
Page 317: Url Content Filter Profile
To provide an appropriate cyberspace to users, Vigor router equips with URL Content Filter not only to limit illegal traffic from/to the inappropriate web sites but also prohibit other web feature where malicious code may conceal. Once a user type in or click on an URL with objectionable keywords, URL keyword blocking facility will decline the HTTP request to that web page thus can limit user’s access to the website.
Page 318 Administration Message You can type the message manually for your necessity. Default Message - You can type the message manually for your necessity or click this button to get the default message which will be displayed on the field of Administration Message.
Page 319 matching with the conditions specified in URL Access Control and Web Feature below, such function can determine the priority for the actions executed. For this one, the router will process the packages with the conditions set below for web feature first, then URL second. None –...
Page 320 supports multiple keywords. The keyword could be a noun, a partial noun, or a complete URL string. Multiple keywords within a frame are separated by space, comma, or semicolon. In addition, the maximal length of each frame is 32-character long. After specifying keywords, the Vigor router will decline the connection request to the website whose URL string matched to any user-defined keyword.
Page 321: Web Content Filter Profile
Note: If you have used Service Activation Wizard to activate WCF service, you can skip this section. WCF adopts the mechanism developed and offered by certain service provider (e.g., DrayTek). No matter activating WCF feature or getting a new license for web content filter, you have to click Activate to satisfy your request.
Page 322 Setup Test Server It is recommended for you to use the default setting, auto-selected. Find more Click it to open http://myvigor.draytek.com for searching another qualified and suitable server. Click this link to do the verification. Test a site to verify...
Page 323 Cache None – the router will check the URL that the user wants to access via WCF precisely, however, the processing rate is normal. Such item can provide the most accurate URL matching. L1 – the router will check the URL that the user wants to access via WCF.
Page 324 Available settings are explained as follows: Item Description Profile Name Type a name for the profile. The maximum length of the name you can set is 15 characters. Black/White List Enable – Activate white/black list function for such profile. Group/Object Selections – Click Edit to choose the group or object profile as the content of white/black list.
Page 325: Dns Filter Profile
The DNS Filter monitors DNS queries on UDP port 53 and will pass the DNS query information to the WCF to help with categorizing HTTPS URL's. DNS can be specified in LAN>>General Setup by using the server (e.g., 168.95.1.1) on router or external DNS server (e.g., 8.8.8.8).
Page 326 DNS Filter General DNS Filter General Setting will be applied to DNS query Setting from clients on LAN when router’s DNS server is used. DNS Filter - Check Enable to enable such feature. Syslog - The filtering result can be recorded according to the setting selected for Syslog.
Page 327: Bandwidth Management
Below shows the menu items for Bandwidth Management. A PC with private IP address can access to the Internet via NAT router. The router will generate the records of NAT sessions for such connection. The P2P (Peer to Peer) applications (e.g., BitTorrent) always need many sessions for procession and also they will occupy over resources which might result in important accesses impacted.
Page 328 session. Default session limit - Defines the default session number used for each computer in LAN. Limitation List Displays a list of specific limitations that you set on this web page. Start IP- Defines the start IP address for limit session. Specific Limitation End IP - Defines the end IP address for limit session.
Page 329: Bandwidth Limit
The downstream or upstream from FTP, HTTP or some P2P applications will occupy large of bandwidth and affect the applications for other programs. Please use Limit Bandwidth to make the bandwidth usage more efficient. In the Bandwidth Management menu, click Bandwidth Limit to open the web page. To activate the function of limit bandwidth, simply click Enable and set the default upstream and downstream limit.
Page 330 downstream for each computer in LAN. Allow auto adjustment….- Check this box to make the best utilization of available bandwidth. Limitation List Display a list of specific limitations that you set on this web page. Specific Limitation Start IP - Define the start IP address for limit bandwidth. End IP - Define the end IP address for limit bandwidth.
Page 331: Quality Of Service
Deploying QoS (Quality of Service) management to guarantee that all applications receive the service levels required and sufficient bandwidth to meet performance expectations is indeed one important aspect of modern enterprise network. One reason for QoS is that numerous TCP-based applications tend to continually increase their transmission rate and consume all available bandwidth, which is called TCP slow start.
Page 332 However, each node may take different attitude toward packets with high priority marking since it may bind with the business deal of SLA among different DS domain owners. It’s not easy to achieve deterministic and consistent high-priority QoS traffic throughout the whole network with merely Vigor router’s effort.
Page 333 Item Description service type. Enable the First Priority When this feature is enabled, the VoIP SIP/UDP packets will for VoIP SIP/RTP be sent with highest priority. SIP UDP Port – Set a port number used for SIP. This page displays the QoS settings result of the WAN interface. Click the Setup link to access into next page for the general setup of WAN interface.
Page 334 Available settings are explained as follows: Item Description Enable the QoS Control The factory default for this setting is checked. Please also define which traffic the QoS Control settings will apply to. IN - apply to incoming traffic only. OUT - apply to outgoing traffic only. BOTH - apply to both incoming and outgoing traffic.
Page 335 Prioritize are great in ADSL2+ environment. For the download speed might be impacted by the uploading TCP ACK, you can check this box to push ACK of upload faster to speed the network traffic. Limited_bandwidth Ratio The ratio typed here is reserved for limited bandwidth of UDP application.
Page 336 For adding a new rule, click Add to open the following page. Available settings are explained as follows: Item Description Check this box to invoke these settings. Hardware Check this box to enable the hardware acceleration when Acceleration such rule is applied. Ethernet Type Please specify which protocol (IPv4 or IPv6) will be used for this rule.
Page 337 Service Type It determines the service type of the data for processing with QoS control. It can also be edited. You can choose the predefined service type from the Service Type drop down list. Those types are predefined in factory. Simply choose the one that you want for using by current QoS.
Page 338 After you click the Edit link, you will see the following page. For adding a new service type, click Add to open the following page. Available settings are explained as follows: Item Description Service Name Type in a new service for your request. The maximum length of the name you can set is 11 characters.
Page 339 Packets coming from LAN IP can be retagged through QoS setting. When the packets sent out through WAN interface, all of them will be tagged with certain header and that will be easily to be identified by server on ISP. For example, in the following illustration, the VoIP packets in LAN go into Vigor router without any header.
Page 340: Applications
Below shows the menu items for Applications. The ISP often provides you with a dynamic IP address when you connect to the Internet via your ISP. It means that the public IP address assigned to your router changes each time you access the Internet.
Page 341 Available settings are explained as follows: Item Description Set to Factory Clear all profiles and recover to factory settings. Default Enable Dynamic Check this box to enable DDNS function. DNS Setup Display DDNS log status. View Log Force Update Force the router updates its information to DDNS server. Auto-Update Set the time for the router to perform auto update for DDNS interval...
Page 342 WAN Interface WAN1/WAN2/WAN3/WAN4 First - While connecting, the router will use WAN1/WAN2/WAN3/WAN4 as the first channel for such account. If WAN1/WAN2/WAN3 /WAN4 fails, the router will use another WAN interface instead. WAN1/WAN2/WAN3/WAN4 Only - While connecting, the router will use WAN1/WAN2/WAN3/WAN4 as the only channel for such account.
Page 343: Lan Dns / Dns Forwarding
The LAN DNS lets the network administrators host servers with privacy and security. When the network administrators of your office set up FTP, Mail or Web server inside LAN, you can specify specific private IP address (es) to correspondent servers. Thus, even the remote PC is adopting public DNS as the DNS server, the LAN DNS resolution on Vigor2925 series will respond the specified private IP address.
Page 344 Index Click the number below Index to access into the setting page. Profile Display the name of the LAN DNS profile. Display the domain name of the LAN DNS profile. Domain Name You can set up to 20 LAN DNS profiles. To create a LAN DNS profile: Click any index, say Index No.
Page 345 IP Address List The IP address listed here will be used for mapping with the domain name specified above. In general, one domain name maps with one IP address. If required, you can configure two IP addresses mapping with the same domain name. Add –...
Page 346: Schedule
DNS Server IP Type the IP address of the DNS server you want to use for Address DNS forwarding. Click OK button to save the settings. A new LAN DNS profile has been created. The Vigor router has a built-in clock which can update itself manually or automatically by means of the Network Time Protocols (NTP) selected on System Maintenance>>Time and Date.
Page 347 Index Click the number below Index to access into the setting page of schedule. Status Display if this schedule setting is active or inactive. You can set up to 15 schedules. Then you can apply them to your Internet Access or VPN and Remote Access >>...
Page 348 Idle Timeout Specify the duration (or period) for the schedule. How often -Specify how often the schedule will be applied Once -The schedule will be applied just once Weekdays -Specify which days in one week should perform the schedule. Click OK button to save the settings. Example Suppose you want to control the PPPoE Internet access connection to be always on (Force On) from 9:00 to 18:00 for whole week.
Page 349: Radius/Tacacs
Remote Authentication Dial-In User Service (RADIUS) is a security authentication client/server protocol that supports authentication, authorization and accounting, which is widely used by Internet service providers. It is the most common method of authenticating and authorizing dial-up and tunneled network users. The built-in RADIUS client feature enables the router to assist the remote dial-in user or a wireless station and the RADIUS server in performing mutual authentication.
Page 350 It means Terminal Access Controller Access-Control System Plus. It works like RADIUS does. Click the TACACS+ Setup to open the following page: Available settings are explained as follows: Item Description Enable Check to enable TACACS+ feature. Server IP Address Enter the IP address of TACACS+ server. Destination Port The UDP port number that the TACACS+ server is using.
Page 351: Active Directory/ Ldap
Lightweight Directory Access Protocol (LDAP) is a communication protocol for using in TCP/IP network. It defines the methods to access distributing directory server by clients, work on directory and share the information in the directory by clients. The LDAP standard is established by the work team of Internet Engineering Task Force (IETF).
Page 352 For the regular mode, you’ll need to type in the Regular DN and Regular Password. Server IP Address Enter the IP address of LDAP server. Destination Port Type a port number as the destination port for LDAP server. Use SSL Check the box to use the port number specified for SSL.
Page 353 Available settings are explained as follows: Item Description Name Type a name for such profile. Common Name Type or edit the common name identifier for the LDAP server. Identifier The common name identifier for most LDAP server is “cn”. Additional Filter Type the condition for additional filter.
Page 354: Upnp
The UPnP (Universal Plug and Play) protocol is supported to bring to network connected devices the ease of installation and configuration which is already available for directly connected PC peripherals with the existing Windows 'Plug and Play' system. For NAT routers, the major feature of UPnP on the router is “NAT Traversal”.
Page 355 and configure port mappings on the router. Subsequently, such a facility forwards packets from the external ports of the router to the internal ports used by the application. The reminder as regards concern about Firewall and UPnP Can't work with Firewall Software Enabling firewall applications on your PC may cause the UPnP function not working properly.
Page 356: Igmp
IGMP is the abbreviation of Internet Group Management Protocol. It is a communication protocol which is mainly used for managing the membership of Internet Protocol multicast groups. Available settings are explained as follows: Item Description Enable IGMP Proxy Check this box to enable this function. The application of multicast will be executed through WAN port.
Page 357: Wake On Lan
A PC client on LAN can be woken up by the router it connects. When a user wants to wake up a specified PC through the router, he/she must type correct MAC address of the specified PC on this web page of Wake on LAN (WOL) of this router. In addition, such PC must have installed a network card supporting WOL function.
Page 358: Sms / Mail Alert Service
The function of SMS (Short Message Service)/Mail Alert is that Vigor router sends a message to user’s mobile or e-mail box through specified service provider to assist the user knowing the real-time abnormal situations. Vigor router allows you to set up to 10 SMS profiles which will be sent out according to different conditions.
Page 359 This page allows you to specify Mail Server profile, who will get the notification e-mail, what the content is and when the message will be sent. Available settings are explained as follows: Item Description Index Check the box to enable such profile. Mail Service Use the drop down list to choose mail service provider.
Page 360: Bonjour
Bonjour is a service discovery protocol which is a built-in service in Mac OS X; for Windows or Linux platform, there are correspondent software to enable this function for free. Usually, users have to configure the router or personal computers to use above services. Sometimes, the configuration (e.g., IP settings, port number) is complicated and not easy to complete.
Page 361 2. Open the web browse, Firefox. If Bonjour and DNSSD have been installed, you can open the web page (DNSSD) and see the following results. 3. Open System Maintenance>>Management. Type a name (e.g., Dray_2925) as the Router Name and click OK. 4.
Page 362 5. Open the DNSSD page again. The available items will be changed as the follows. It means the Vigor router (based on Bonjour protocol) is ready to be used as a printer server, FTP server, SSH Server, Telnet Server, and HTTP Server. 6.
Page 363: Vpn And Remote Access
A Virtual Private Network (VPN) is the extension of a private network that encompasses links across shared or public networks like the Internet. In short, by VPN technology, you can send data between two computers across a shared or public network in a manner that emulates the properties of a point-to-point private link.
Page 364: Remote Access Control
Enable the necessary VPN service as you need. If you intend to run a VPN server inside your LAN, you should disable the VPN service of Vigor Router to allow VPN tunnel pass through, as well as the appropriate NAT settings, such as DMZ or open port. After finishing all the settings here, please click OK to save the configuration.
Page 365 PAP/CHAP/MS-CHAP/MS-CHAPv2 - Selecting this option means the router will attempt to authenticate dial-in users with the CHAP protocol first. If the dial-in user does not support this protocol, it will fall back to use the PAP protocol for authentication. Dial-In PPP Encryption Optional MPPE - This option represents that the MPPE (MPPE) encryption method will be optionally employed in the...
Page 366: Ipsec General Setup
In IPSec General Setup, there are two major parts of configuration. There are two phases of IPSec.  Phase 1: negotiation of IKE parameters including encryption, hash, Diffie-Hellman parameter values, and lifetime to protect the following IKE exchange, authentication of both peers using either a Pre-Shared Key or Digital Signature (x.509).
Page 367: Ipsec Peer Identity
from remote dial-in user, Certificate (X.509) and Pre-Shared Key. Certificate for Dial-in –Choose one of the local certificates from the drop down list. Pre-Shared Key- Specify a key for IKE authentication. Confirm Pre-Shared Key- Retype the characters to confirm the pre-shared key. Note: Any packets from the remote dial-in user which does not match the rule defined in VPN and Remote Access>>Remote Dial-In User will be applied with the...
Page 368 Index Click the number below Index to access into the setting page of IPSec Peer Identity. Name Display the profile name of that index. Click each index to edit one peer digital certificate. There are three security levels of digital signature authentication: Fill each necessary field to authenticate the remote peer.
Page 369: Remote Dial-In User
You can manage remote access by maintaining a table of remote user profile, so that users can be authenticated to dial-in via VPN connection. You may set parameters including specified connection peer ID, connection type (VPN connection - including PPTP, IPSec Tunnel, and L2TP by itself or over IPSec) and corresponding security methods, etc.
Page 370 Status Display the access state of the specific dial-in user. The symbol V and X represent the specific dial-in user to be active and inactive, respectively. Click each index to edit one remote user profile. Each Dial-In Type requires you to fill the different corresponding fields on the right.
Page 371 below:  None - Do not apply the IPSec policy. Accordingly, the VPN connection employed the L2TP without IPSec policy can be viewed as one pure L2TP connection.  Nice to Have - Apply the IPSec policy first, if it is applicable during negotiation.
Page 372: Lan To Lan
Method L2TP with IPSec Policy when you specify the IP address of the remote node. The only exception is Digital Signature (X.509) can be set when you select IPSec tunnel either with or without specify the IP address of the remote node. Pre-Shared Key - Check the box of Pre-Shared Key to invoke this function and type in the required characters (1-63) as the pre-shared key.
Page 373 The following shows profiles joined into VPN Load Balance and VPN Backup mechanism. Available settings are explained as follows: Item Description View All – Click it to display the LAN to LAN profiles. Online – Click it to display the online profiles. Offline –...
Page 374 Status Online – means such LAN to LAN profile is in use. Offline – means such LAN to LAN profile isn’t in use even if the profile has been enabled. To edit each profile: Click each index to edit each profile and you will get the following page. Each LAN-to-LAN profile includes 4 subgroups.
Page 375  WAN1 First/ WAN2 First/ WAN3 First /WAN4 First- While connecting, the router will use WAN1/WAN2/WAN3 as the first channel for VPN connection. If WAN1/WAN2/WAN3/WAN4 fails, the router will use another WAN interface instead. WAN1 Only /WAN2 Only/WAN 3 Only/WAN 4 Only- While connecting, the router will use WAN1/WAN2/WAN3/WAN4 as the only channel for VPN connection.
Page 376 especially useful in the case of abnormal VPN IPSec tunnel disruption. For details, please refer to the note below. Check to enable the transmission of PING packets to a specified IP address. Enable PING to keep alive is used to handle abnormal IPSec VPN connection disruption.
Page 377 IKE Authentication Method - This group of fields is applicable for IPSec Tunnels and L2TP with IPSec Policy.  Pre-Shared Key - Input 1-63 characters as pre-shared key.  Digital Signature (X.509) - Select one predefined Profiles set in the VPN and Remote Access >>IPSec Peer Identity.
Page 378 IKE phase 1 mode -Select from Main mode and Aggressive mode. The ultimate outcome is to exchange security proposals to create a protected secure channel. Main mode is more secure than Aggressive mode since more exchanges are done in a secure channel to set up the IPSec session.
Page 379 Available settings are explained as follows: Item Description Dial-In Settings Allowed Dial-In Type - Determine the dial-in connection with different types.  PPTP - Allow the remote dial-in user to make a PPTP VPN connection through the Internet. You should set the User Name and Password of remote dial-in user below.
Page 380 Specify Remote VPN Gateway - You can specify the IP address of the remote dial-in user or peer ID (should be the same with the ID setting in dial-in type) by checking the box. Also, you should further specify the corresponding security methods on the right side.
Page 381 AES. GRE over IPSec Enable IPSec Dial-Out function GRE over IPSec: Check Settings this box to verify data and transmit data in encryption with GRE over IPSec packet after configuring IPSec Dial-Out setting. Both ends must match for each other by setting same virtual IP address for communication.
Page 382 RIP Direction - The option specifies the direction of RIP (Routing Information Protocol) packets. You can enable/disable one of direction here. Herein, we provide four options: TX/RX Both, TX Only, RX Only, and Disable. From first subnet to remote network, you have to do - If the remote network only allows you to dial in with single IP, please choose NAT, otherwise choose Route.
Page 383 VPN router. Translated Type – There are two types for you to choose.  Whole Subnet  Specific IP Address Virtual IP Mapping – A pop up dialog will appear for you to specify the local IP address and the mapping virtual IP address.
Page 384: Vpn Trunk Management
VPN trunk includes four features - VPN Backup, VPN load balance, GRE over IPSec, and Binding tunnel policy. – – VPN TRUNK Management is a backup mechanism which can set multiple VPN tunnels as backup tunnel. It can assure the network connection not to be cut off due to network environment blocked by any reason.
Page 385 Available settings are explained as follows: Item Description Backup Profile List Set to Factory Default - Click to clear all VPN TRUNK-VPN Backup mechanism profile. No – The order of VPN TRUNK-VPN Backup mechanism profile. Status - “v” means such profile is enabled; “x” means such profile is disabled.
Page 386 Member2 drop down list below. Advanced – This button is available only when LAN to LAN profile (or more) is created. Detailed information for this dialog, see later section - Advanced Load Balance and Backup. Set to Factory Default - Click to clear all VPN Load Balance Profile List TRUNK-VPN Load Balance mechanism profile.
Page 387 Detailed information for this dialog, see later section - Advanced Load Balance and Backup. General Setup Status- After choosing one of the profile listed above, please click Enable to activate this profile. If you click Disable, the selected or current used VPN TRUNK-Backup/Load Balance mechanism profile will not have any effect for VPN tunnel.
Page 388 profiles in LAN-to-LAN will be displayed in blue. Update- Click this button to save the changes to the Status (Enable or Disable), profile name, member1 or member2. Delete - Click this button to delete the selected VPN TRUNK profile. The corresponding members (LAN-to-LAN profiles) grouped in the deleted VPN TRUNK profile will be released and that profiles in LAN-to-LAN will be displayed in black.
Page 389 Take a look for LAN-to-LAN profiles. Index 1 is chosen as Member1; index 2 is chosen as Member2. For such reason, LAN-to-LAN profiles of 1 and 2 will be expressed in red to indicate that they are fixed. If you delete the VPN TRUNK – VPN Backup/Load Balance mechanism profile, the selected LAN-to-LAN profiles will be released and expressed in black.
Page 390 After setting profiles for load balance, you can choose any one of them and click Advance for more detailed configuration. The windows for advanced load balance and backup are different. Refer to the following explanation: Advanced Load Balance Available settings are explained as follows: Item Description List the load balance profile name.
Page 391 user to adjust suitable rate manually. There are 100 groups of rate ratio for Member1:Member2 (range from 1:99 to 99:1). VPN Load Balance Policy Below shows the algorithm for Load Balance. Edit – Click this radio button for assign a blank table for configuring Binding Tunnel.
Page 392 Detail Information This field will display detailed information for Binding Tunnel Policy. Below shows a successful binding tunnel policy for load balance: Note : To configure a successful binding tunnel, you have to: Type Binding Src IP range (Start and End) and Binding Des IP range (Start and End).
Page 393: Connection Management
Item Description Profile Name List the backup profile name. ERD Mode ERD means “Environment Recovers Detection”. Normal – choose this mode to make all dial-out VPN TRUNK backup profiles being activated alternatively. Resume – when VPN connection breaks down or disconnects, Member 1 will be the top priority for the system to do VPN connection.
Page 394: Certificate Management
VPN Server IP address). The VPN connection built by Backup Mode supports VPN backup function. Dial - Click this button to execute dial out function. Refresh Seconds - Choose the time for refresh the dial information among 5, 10, and 30. Refresh - Click this button to refresh the whole connection status.
Page 395 click Generate again. Import Click this button to import a saved file as the certification information. Refresh Click this button to refresh the information listed below. View Click this button to view the detailed settings for certificate request. Delete Click this button to delete selected name with certification information.
Page 396 IMPORT Vigor router allows you to generate a certificate request and submit it the CA server, then import it as “Local Certificate”. If you have already gotten a certificate from a third party, you may import it directly. The supported types are PKCS12 Certificate and Certificate with a private key.
Page 397 Upload PKCS12 It allows users to import the certificate whose extensions are Certificate usually .pfx or .p12. And these certificates usually need passwords. Note: PKCS12 is a standard for storing private keys and certificates securely. It is used in (among other things) Netscape and Microsoft Internet Explorer with their import and export options.
Page 398: Trusted Ca Certificate
CA to save time and provide convenience for general user. Later, such root CA generated by DrayTek server can perform the issuing of local certificate. Note: Root CA can be deleted but not edited. If you want to modify the settings for a Root CA, please delete the one and create another one by clicking Create Root CA.
Page 399: Imported Trusted Ca
To import a pre-saved trusted CA certificate, please click IMPORT to open the following window. Use Browse… to find out the saved text file. Then click Import. The one you imported will be listed on the Trusted CA Certificate window. Then click Import to use the pre-saved file.
Page 400: Certificate Backup
Local certificate and Trusted CA certificate for this router can be saved within one file. Please click Backup on the following screen to save them. If you want to set encryption password for these certificates, please type characters in both fields of Encrypt password and Retype password.
Page 401: Central Vpn Management
Vigor2925 can build virtual private network (VPN) between itself and any other TR-069 CPE by the function of central VPN management. In addition, it can be treated as a server (called CVM server) which can manage TR-069 CPE for periodical firmware upgrade, configuration backup and restoring configuration.
Page 402 To enable the CVM feature, the first thing you have to do is enabling CVM port or CVM SSL Port. Available settings are explained as follows: Item Description CVM SSL Port Check the box to enable the port setting. Type the port number in the box. CVM Port Check the box to enable the port setting.
Page 403 Central VPN management is operated through IPsec VPN connection. Available settings are explained as follows: Item Description IPsec Mode Choose Aggressive or Main as the IPsec Mode. Security Method Choose one of the following methods (AH or ESP) for the security of data transmission.
Page 404: Cpe Management
All the CPEs managed by Vigor2925 series can be seen with icons from this page Before using such feature, make sure the CVM port has been enabled and configured properly. This page allows you to manage the CPEs connected to Vigor2925 series. ...
Page 405  Page with CPE connected Available settings are explained as follows: Item Description Managed Devices List This area displays device icons (up to 8) for the CPE managed by Vigor2925 series. Edit – To modify the name and location of specific CPE, click the one you want and click the Edit button.
Page 406 modify any data on the window. Unmanaged Devices List Any device (CPE) which follows the standard of TR-069 can be configured and can be detected by Vigor2925 series automatically. Only eight remote devices can be managed by Vigor2925 at one time. Therefore, other remote devices detected by Vigor2925 series might be displayed in such field.
Page 407 This area displays all the profiles which are created for applying to the managed device. This page can help the administrator to do maintenance jobs like firmware upgrade, configuration backup, configuration restoration and etc. Available settings are explained as follows: Item Description Refresh...
Page 408 File/Path Display the location of the file you want to save, restore or upgrade for CPE. Schedule Display the schedule profiles selected for such profile. The action will be performed for the selected CPE immediately. Follow the steps below to create a new maintenance profile. Click any index number link, e.g., Index 1.
Page 409 used for firmware upgrade. Click Select to locate the file you want to save, restore or File/Path upgrade for CPE. Index in Schedule Vigor2925 series will perform the specified action to the selected CPE based on the schedule configured here. Specify one or two schedule profiles (represented by number) here.
Page 410 To display the location of the managed CPE with a bird’s eye view, open Central VPN Management>>CPE Management and click the tab of Google Map. Vigor2925 Series User’s Guide...
Page 411 An easy and quick method is offered to configure VPN settings for building VPN connection automatically between Vigor2925 series (treated as VPN server) and other Vigor router (treated as CPE device, i.e., VPN client).  Page without CPE connected  Page with CPE connected Vigor2925 Series User’s Guide...
Page 412: Vpn Management
Available parameters are listed as follows: Item Description VPN Management Display Screen Once the device is managed (controlled) by Vigor2925 series, it will be displayed on such screen automatically. If not, refer to sections “4.15 How to manage the CPE (router) through Vigor2925?”...
Page 413: Log & Alert
& & This page offers brief information to identify the CPE connected to Vigor2925 series. Available settings are explained as follows: Item Description Display Mode Choose the mode you want to display the related information on the following table.  Stop record when fulls –...
Page 414: Central Ap Management
Vigor2925 can manage the access points supporting AP management via Central AP Management. This page displays current status (online, offline or SSID hidden, IP address, encryption, channel, version, password and etc.) of the access points managed by Vigor router. Please open Central AP Management>>Function Support List to check what AP Models are supported.
Page 415: Wlan Profile
number displayed on the right side means 5Ghz. Version Display the firmware version used by the access point. Password Vigor2925 can get related information of the access point by accessing into the web user interface of the access point. This button is used to modify the logging password of the connected access point.
Page 416 WLAN profile. First, you have to check the box of the existing profile as the original profile. Second, click Clone. The following dialog will appear. Third, choose the profile index to accept the settings from the original profile. Forth, type a new name in the field of Renamed as.
Page 417 1. Check the box on the left side of the selected profile. 2. Click the Edit button to display the following page. 3. After finished the general settings configuration, click Next to open the following page for 2.4G wireless security settings. Vigor2925 Series User’s Guide...
Page 418 4. After finished the above web page configuration, click Next to open the following page for 5G wireless security settings. 5. When you finished the above web page configuration, click Finish to exit and return to the first page. The modified WLAN profile will be shown on the web page. Vigor2925 Series User’s Guide...
Page 419: Ap Maintenance
Vigor router can execute configuration backup, configuration restoration, firmware upgrade and remote reboot for the APs managed by the router. It is very convenient for the administrator to process maintenance without accessing into the web user interface of the access point. Note: Config Backup can be performed to one AP at one time.
Page 420: Traffic Graph
Click Traffic Graph to open the web page. Choose one of the managed Access Points, LAN-A or LAN-B, daily or weekly for viewing data transmission chart. Click Refresh to renew the graph at any time. Note: Enabling/Disabling such function will also enable/disable the External Devices function.
Page 421 Available settings are explained as follows: Item Description Enable Neighbor AP Detection – The access point(s) registered to Vigor2925 will be used to detect other access points and send the scanned results to Vigor2925. Later, the scanned result will be displayed on this page. Local WLAN Detection –...
Page 422 AP is friendly and which one is Rogue respectively. Follow the steps below to perform the classification of access points. 1. Click the radio button on one of the access points. In this case, DrayTek-LAN-A is selected. 2. Later, some options will appear on the bottom of the page.
Page 423 unknown to Friendly. Rogue APs - If the selected AP shall be treated as rogue AP, simply click Add to change its classification from unknown to Rogue. Delete From Rogue APs - If you want to change the classification of the rogue AP, simply choose the one and click Delete.
Page 424: Load Balance
The parameters configured for Load Balance can help to distribute the traffic for all of the access points registered to Vigor router. Thus, the bandwidth will not be occupied by certain access points. Available settings are explained as follows: Item Description Enable Check the box to enable such function.
Page 425: Function Support List
Upload Limit –Use the drop down list to specify the traffic limit for uploading. Download Limit – Use the drop down list to specify the traffic limit for downloading. Force Overload By Idle Time - When the access point is overload (e.g., Disassociation reaching the limit of station number or limit of network traffic), it will terminate the network connection of the client’s...
Page 426: Voip
Note: This function is used for “V” models. Voice over IP network (VoIP) enables you to use your broadband Internet connection to make toll quality voice calls over the Internet. There are many different call signaling protocols, methods by which VoIP devices can talk to each other.
Page 427 The major benefit of this mode is that you don’t have to memorize your friend’s IP address, which might change very frequently if it’s dynamic. Instead of that, you will only have to using dial plan or directly dial your friend’s account name if you are with the same SIP Registrar.
Page 428: Dialplan
This page allows you to set phone book, digit map, call barring, regional settings and PSTN setup for the VoIP function. Click the links on this page to access into next pages for detailed settings. Available settings are explained as follows: Item Description Enable Secure Phone...
Page 429 In this section, you can set your VoIP contacts in the “phonebook”. It can help you to make calls quickly and easily by using “speed-dial” Phone Number. There are total 60 index entries in the phonebook for you to store all your friends and family members’ SIP addresses. Loop through and Backup Phone Number will be displayed if you are using Vigor2830Vn for setting the phone book.
Page 430 number you choose, using digits 0-9 and * . Display Name The Caller-ID that you want to be displayed on your friend’s screen. This let your friend can easily know who’s calling without memorizing lots of SIP URL Address. SIP URL Enter your friend’s SIP Address.
Page 431 For the convenience of user, this page allows users to edit prefix number for the SIP account with adding number, stripping number or replacing number. It is used to help user having a quick and easy way to dial out through VoIP interface. Available settings are explained as follows: Item Description...
Page 432 03 will be replaced by 8863. For example: dial number of “031111111” will be changed to “88631111111” and sent to SIP server. OP Number The front number you type here is the first part of the account number that you want to execute special function (according to the chosen mode) by using the prefix number.
Page 433 Click any index number to display the dial plan setup page. Available settings are explained as follows: Item Description Enable Check it to enable this entry. Call Direction Determine the direction for the phone call, IN – incoming call, OUT-outgoing call, IN & OUT – both incoming and outgoing calls.
Page 434 For Block Unknown Domain – this function can block incoming calls (through Phone port) from unrecognized domain that is not specified in SIP accounts. Such control also can be done based on preconfigured schedules. For Block IP Address – this function can block incoming calls (through Phone port) coming from IP address.
Page 435 This page allows you to process incoming or outgoing phone calls by regional. Default values (common used in most areas) will be shown on this web page. You can change the number based on the region that the router is placed. Available settings are explained as follows: Item Description...
Page 436 Ans][Act] answer of the connected phone. Do Not Disturb [Act] Dial the number typed in this field to invoke the function of DND. Do Not Distrub [Deact] Dial the number typed in this field to release the DND function. Hide caller ID [Act] Dial the number typed in this field to make your phone number (ID) not displayed on the display panel of remote end.
Page 437: Sip Accounts
After finishing all the settings here, please click OK to save the configuration. In this section, you set up your own SIP settings. When you apply for an account, your SIP service provider will give you an Account Name or user name, SIP Registrar, Proxy, and Domain name.
Page 438 Available settings are explained as follows: Item Description Index Click this link to access into next page for setting SIP account. Profile Display the profile name of the account. Display the domain name or IP address of the SIP registrar Domain/Realm server.
Page 439 SIP PING interval The default value is 150 (sec). It is useful for a Nortel server NAT Traversal Support. Click any index link to access into the following page for configuring SIP account. Available settings are explained as follows: Item Description Profile Name Assign a name for this profile for identifying.
Page 440 SIP Port Set the port number for sending/receiving SIP message for building a session. The default value is 5060. Your peer must set the same value in his/her Registrar. Domain/Realm Set the domain name or IP address of the SIP Registrar server.
Page 441 Call Forwarding There are four options for you to choose. Disable is to close call forwarding function. Always means all the incoming calls will be forwarded into SIP URL without any reason. Busy means the incoming calls will be forwarded into SIP URL only when the local system is busy.
Page 442: Phone Settings
Voice Active Detector This function can detect if the voice on both sides is active or not. If not, the router will do something to save the bandwidth for other using. Click On to invoke this function; click off to close the function. After finishing all the settings here, please click OK to save the configuration.
Page 443 change SIP account for each phone port. DTMF Relay – Display DTMF mode that configured in the advanced settings page of Phone Index. Symmetric RTP – Check this box to invoke the function. To make the data transmission going through on both ends of local router and remote router not misleading due to IP lost (for example, sending data from the public IP of remote router to the private IP of local router), you can check this...
Page 444 Click the number link for Phone port, you can access into the following page for configuring Phone settings. Available settings are explained as follows: Item Description Hotline Check the box to enable it. Type in the SIP URL in the field for dialing automatically when you pick up the phone set.
Page 445 response. Click hook flash to pick up the waiting phone call. Call Transfer Check this box to invoke this function. Click hook flash to initiate another phone call. When the phone call connection succeeds, hang up the phone. The other two sides can communicate, then.
Page 446 congestion tone by yourself for VoIP phone. Also, you can specify each field for your necessity. It is recommended for you to use the default settings for VoIP communication. Volume Gain Mic Gain (1-10)/Speaker Gain (1-10) - Adjust the volume of microphone and speaker by entering number from 1- 10.
Page 447: Status
it to digital form then send to the other side; the receiver will generate the tone according to the digital form it receive. This function is very useful when the network traffic congestion occurs and it still can remain the accuracy of DTMF tone. ...
Page 448: Wireless Lan(2.4Ghz/5Ghz)
HANG_UP - Indicates that the connection is not established (busy tone). CONNECTING - Indicates that the user is calling out. WAIT_ANS - Indicates that a connection is launched and waiting for remote user’s answer. ALERTING - Indicates that a call is coming. ACTIVE-Indicates that the VoIP connection is launched.
Page 449 In an Infrastructure Mode of wireless network, Vigor wireless router plays a role as an Access Point (AP) connecting to lots of wireless clients or Stations (STA). All the STAs will share the same Internet connection via Vigor wireless router. The General Settings will set up the information of this wireless network, including its SSID as identification, located channel etc.
Page 450 In WPA-Personal, a pre-defined key is used for encryption during data transmission. WPA applies Temporal Key Integrity Protocol (TKIP) for data encryption while WPA2 applies AES. The WPA-Enterprise combines not only encryption but also authentication. Since WEP has been proved vulnerable, you may consider using WPA for the most secure connection.
Page 451: General Setup
By clicking the General Settings, a new web page will appear so that you could configure the SSID and the wireless channel. Please refer to the following figure for more information. Available settings are explained as follows: Item Description Enable Wireless LAN Check the box to enable wireless function.
Page 452 For 5 GHz: At present, the router can connect to 11a Only, 11n Only (5 GHz), Mixed (11a+11n) stations simultaneously. Simply choose Mixed (11a+11n) mode. In which, 802.11b/g operates on 2.4G band, 802.11a operates on 5G band, and 802.11n operates on either 2.4G or 5G band.
Page 453 Note: For the restricted channels on DFS, please refer to 4.17.1 Basic Concepts for more detailed information. Check it to prevent from wireless sniffing and make it Hide SSID harder for unauthorized clients or STAs to join your wireless LAN. Depending on the wireless utility, the user may only see the information except SSID or just cannot see any thing about Vigor wireless router while site surveying.
Page 454: Security
This page allows you to set security with different modes for SSID 1, 2, 3 and 4 respectively. After configuring the correct settings, please click OK to save and invoke it. The password (PSK) of default security mode is provided and stated on the label pasted on the bottom of the router.
Page 455 Note: You should also set RADIUS Server simultaneously if 802.1x mode is selected. Disable - Turn off the encryption mechanism. WEP-Accepts only WEP clients and the encryption key should be entered in WEP Key. WEP/802.1x Only - Accepts only WEP clients and the encryption key is obtained dynamically from RADIUS server with 802.1X protocol.
Page 456: Access Control
128-Bit - For 128 bits WEP key, either 13 ASCII characters, such as ABCDEFGHIJKLM (or 26 hexadecimal digits leading by 0x, such as 0x4142434445464748494A4B4C4D). All wireless devices must support the same WEP encryption bit size and have the same key. Four keys can be entered here, but only one key can be selected at a time.
Page 457: Wps
can be grouped under SSID 1 and SSID 2 at the same time if you check SSID 1 and SSID 2. MAC Address Filter Display all MAC addresses that are edited before. Client’s MAC Address Manually enter the MAC address of wireless client. Apply SSID After entering the client’s MAC address, check the box of the SSIDs desired to insert this MAC address into their...
Page 458  On the side of Vigor2925 series which served as an AP, press WPS button once on the front panel of the router or click Start PBC on web configuration interface. On the side of a station with network card installed, press Start PBC button of network card. ...
Page 459 Below shows Wireless LAN>>WPS web page: Available settings are explained as follows: Item Description Enable WPS Check this box to enable WPS setting. WPS Status Display related system information for WPS. If the wireless security (encryption) function of the router is properly configured, you can see ‘Configured’...
Page 460: Wds
WDS means Wireless Distribution System. It is a protocol for connecting two access points (AP) wirelessly. Usually, it can be used for the following application:  Provide bridge traffic between two LANs through the air.  Extend the coverage range of a WLAN. To meet the above requirement, two WDS modes are implemented in Vigor router.
Page 461 Bridge mode, packets received from a WDS link will only be forwarded to local wired or wireless hosts. In other words, only Repeater mode can do WDS-to-WDS packet forwarding. In the following examples, hosts connected to Bridge 1 or 3 can communicate with hosts connected to Bridge 2 through WDS links.
Page 462 Available settings are explained as follows: Item Description Mode Choose the mode for WDS setting. Disable mode will not invoke any WDS setting. Bridge mode is designed to fulfill the first type of application. Repeater mode is for the second one. Security There are three types for security, Disable, WEP and Pre-shared key.
Page 463: Advanced Setting
This page allows users to set advanced settings such as operation mode, channel bandwidth, guard interval, and aggregation MSDU for wireless data transmission. Available settings are explained as follows: Item Description Operation Mode Mixed Mode – the router can transmit data with the ways supported in both 802.11a/b/g and 802.11n standards.
Page 464 Aggregation MSDU combine frames with different Aggregation MSDU can sizes. It is used for improving MAC layer’s performance for some brand’s clients. The default setting is Enable. This option is to define the length of the sync field in an Long Preamble 802.11 packet.
Page 465: Wmm Configuration
WMM is an abbreviation of Wi-Fi Multimedia. It defines the priority levels for four access categories derived from 802.1d (prioritization tabs). The categories are designed with specific types of traffic, voice, video, best effort and low priority data. There are four accessing categories - AC_BE , AC_BK, AC_VI and AC_VO for WMM.
Page 466 categories must be smaller; however, the difference between AC_BE and AC_BK categories must be greater. Txop It means transmission opportunity. For WMM categories of AC_VI and AC_VO that need higher priorities in data transmission, please set greater value for them to get highest transmission opportunity.
Page 467: Ap Discovery
Vigor router can scan all regulatory channels and find working APs in the neighborhood. Based on the scanning result, users will know which channel is clean for usage. Also, it can be used to facilitate finding an AP for a WDS link. Notice that during the scanning process (about 5 seconds), no client is allowed to connect to Vigor.
Page 468: Station List
Station List provides the knowledge of connecting wireless clients now along with its status code. There is a code summary below for explanation. For convenient Access Control, you can select a WLAN station and click Add to Access Control below. Available settings are explained as follows: Item Description...
Page 469 Available settings are explained as follows: Item Description SSID Display the SSID that the wireless station will use it to connect with Vigor router. Enable Check the box to enable the station control function. Connection Time / Use the drop down list to choose the duration for the wireless Reconnection Time client connecting /reconnecting to Vigor router.
Page 470: Ssl Vpn
An SSL VPN (Secure Sockets Layer virtual private network) is a form of VPN that can be used with a standard Web browser. There are two benefits that SSL VPN provides:  It is not necessary for users to preinstall VPN client software for executing SSL VPN connection.
Page 471: Ssl Web Proxy
After finishing all the settings here, please click OK to save the configuration. SSL Web Proxy will allow the remote users to access the internal web sites over SSL. Each item is explained as follows: Item Description Name Display the name of the profile that you create. Display the URL.
Page 472: Ssl Application
Host IP Address If you type function variation as URL, you have to type corresponding IP address in this filed. Such field must match with URL setting. Access Method There are three modes for you to choose. Disable – the profile will be inactive. If you choose Disable, all the web proxy profile appeared under VPN remote dial-in web page will disappear.
Page 473 2. The following page will appear. Available settings are explained as follows: Item Description Enable Application Check the box to enable such profile. Server Application Name Type a name for such application. The length of the name is limited to 23 characters. Application There are three types offered for you to create an application profile.
Page 474 for this protocol. Port If you choose VNC or RDP, you have to specify the port used for this protocol. The default setting is 5900. Idle Timeout If you choose VNC, you have to specify the time for disconnecting the SSL VPN tunnel. Scaling If you choose VNC, you have to choose the percentage (100%, 80%, 60%) for such application.
Page 475: User Account
With SSL VPN, Vigor2925 series let teleworkers have convenient and simple remote access to central site VPN. The teleworkers do not need to install any VPN software manually. From regular web browser, you can establish VPN connection back to your main office even in a guest network or web cafe.
Page 476 Available settings are explained as follows: Item Description User account and Enable this account - Check the box to enable this function. Authentication Idle Timeout- If the dial-in user is idle over the limitation of the timer, the router will drop this connection. By default, the Idle Timeout is set to 300 seconds.
Page 477 Item Description SSL Tunnel - It allows the remote dial-in user to make an SSL VPN Tunnel connection through Internet, suitable for the application through network accessing (e.g., PPTP/L2TP/IPSec) If you check this box, the function of SSL Tunnel for this account will be activated immediately.
Page 478 Item Description IKE Authentication This group of fields is applicable for IPSec Tunnels and L2TP Method with IPSec Policy when you specify the IP address of the remote node. The only exception is Digital Signature (X.509) can be set when you select IPSec tunnel either with or without specify the IP address of the remote node.
Page 479: User Group
There are 10 user group profiles which can be created for authentication. Such profiles will be used by applications such as User Management, VPN and etc. Each item is explained as follows: Item Description Set to Factory Default Click to clear all indexes. Index Display the number link of the profile.
Page 480 Item Description Enable Check this box to enable such profile. Group Name Type a name for such profile. The length of the name is limited to 23 characters. Access Authority Specify the authority for such profile. At present, Vigor router allows you to create SSL Web Proxy and SSL Application profiles used for SSL VPN.
Page 481: Online User Status
If you have finished the configuration of SSL Web Proxy (server), users can find out corresponding settings when they access into DrayTek SSL VPN portal interface. Next, users can open SSL VPN>> Online Status to view logging status of SSL VPN.
Page 482: Usb Application
USB storage disk connected on Vigor router can be regarded as a server. By way of Vigor router, clients on LAN can access, write and read data stored in USB storage disk with different applications. After setting the configuration in USB Application, you can type the IP address of the Vigor router and username/password created in USB Application>>USB User Management on the client software.
Page 483: Usb User Management
Item Description General Settings Simultaneous FTP Connections - This field is used to specify the quantity of the FTP sessions. The router allows up to 6 FTP sessions connecting to USB storage disk at one time. Default Charset - At present, Vigor router supports four types of character sets.
Page 484 Click index number to access into configuration page. Available settings are explained as follows: Item Description FTP/Samba User Enable – Click this button to activate this profile (account) for FTP service or Samba User service. Later, the user can use the username specified in this page to login into FTP server.
Page 485 ON, you cannot type any new folder name in this field. Only “/” can be used in such case. You can click to open the following dialog to add any new folder which can be specified as the Home Folder. Access Rule It determines the authority for such profile.
Page 486: File Explorer
File Explorer offers an easy way for users to view and manage the content of USB storage disk connected on Vigor router. Available settings are explained as follows: Item Description Click this icon to refresh files list. Refresh Click this icon to return to the upper directory. Back Click this icon to add a new folder.
Page 487: Usb Device Status
This page is to monitor the status for the users who accessing into FTP or Samba server (USB storage disk) via the Vigor router. In addition, the status of the USB modem or USB printer connecting to Vigor router can be checked from such page. If you want to remove the storage disk from USB port in router, please click Disconnect USB Disk first.
Page 488: Temperature Sensor
A USB Thermometer is now available that complements your installed DrayTek router installations that will help you monitor the server or data communications room environment and notify you if the server room or data communications room is overheating. During summer in particular, it is important to ensure that your server or data communications equipment are not overheating due to cooling system failures.
Page 489: Modem Support List
Below shows an example of temperature graph: Such page provides the information about the brand name and model name of the USB modems which are supported by Vigor router. Vigor2925 Series User’s Guide...
Page 490: System Maintenance
For the system setup, there are several items that you have to know the way of configuration: System Status, TR-069, Administrator Password, User Password, Login Page Greeting, Configuration Backup, Syslog /Mail Alert, Time and Date, Management, Reboot System, Firmware Upgrade and Activation. Below shows the menu items for System Maintenance.
Page 491 Available settings are explained as follows: Item Description Model Name Display the model name of the router. Firmware Version Display the firmware version of the router. Build Date/Time Display the date and time of the current firmware build. MAC Address - Display the MAC address of the LAN Interface.
Page 492: 480
This device supports TR-069 standard. It is very convenient for an administrator to manage a Auto Configuration Server, e.g., TR-069 device through an VigorACS. Available settings are explained as follows: Item Description ACS Server On Choose the interface for the router connecting to ACS server.
Page 493 Enable/Disable – Allow/Deny the CPE Client to connect with Auto Configuration Server. Port – Sometimes, port conflict might be occurred. To solve such problem, you might change port number for CPE. Username and Password – Type the username and password that VigorACS can use to access into such CPE. Periodic Inform Settings The default setting is Enable.
Page 494: Administrator Password
This page allows you to set new password. Available settings are explained as follows: Item Description Administrator Password Old Password - Type in the old password. The factory default setting for password is “admin”. New Password -Type in new password in this field. The length of the password is limited to 23 characters.
Page 495 User Name – Give a user name for the local user. Password – Type the password for the local user. Confirm Password – Type the password again for confirmation. Add – After typing the user name and password above, simply click it to create a new local user. The new one will be shown on the Local User List immediately.
Page 496: User Password
This page allows you to set new password for user operation. Available settings are explained as follows: Item Description After checking this box, you can access into the web user Enable User Mode for interface with the password typed here for simple web simple web configuration configuration.
Page 497 3. The following screen will appear. Simply click OK. 4. Log out Vigor router web user interface by clicking the Logout button. 5. The following window will be open to ask for username and password. Type the new user password in the filed of Password and click Login. Vigor2925 Series User’s Guide...
Page 498 6. The main screen with User Mode will be shown as follows. Settings to be configured in User Mode will be less than settings in Admin Mode. Only basic configuration settings will be available in User Mode. Note: Setting in User Mode can be configured as same as in Admin Mode. Vigor2925 Series User’s Guide...
Page 499: Login Page Title
Check this box to enable the login customization function. Login Page Title Type a brief description (e.g., Welcome to DrayTek) which will be shown on the heading of the login dialog. Type words or sentences here. It will be displayed for Welcome Message and bulletin message.
Page 500 Below shows an example of login customization with the information typed in Login Description and Bulletin. Vigor2925 Series User’s Guide...
Page 501: Configuration Backup
Follow the steps below to backup your configuration. Go to System Maintenance >> Configuration Backup. The following windows will be popped-up, as shown below. Available settings are explained as follows: Item Description Restore Choose File – Click it to specify a file to be restored. Click Restore to restore the configuration.
Page 502 Support Model List Web configuration file from other Vigor router can be applied to Vigor2925 series. At present, only the configuration file of Vigor2920 is accepted for Vigor2925. This field displays model name(s) and firmware which web configuration file saved can be used by such router. Click Backup button to get into the following dialog.
Page 503: Syslog/Mail Alert
Click Choose File button to choose the correct configuration file for uploading to the router. Click Restore button and wait for few seconds, the following picture will tell you that the restoration procedure is successful. SysLog function is provided for users to monitor router. There is no bother to directly get into the Web user interface of the router or borrow debug equipments.
Page 504 Available settings are explained as follows: Item Description SysLog Access Setup Enable - Check Enable to activate function of syslog. Syslog Save to – Check Syslog Server to save the log to Syslog server. USB Disk - Check USB Disk to save the log to the attached USB storage disk.
Page 505 Mail Alert Setup Check Enable to activate function of mail alert. Send a test e-mail - Make a simple test for the e-mail address specified in this page. Please assign the mail address first and click this button to execute a test for verify the mail address is available or not.
Page 506 Vigor2925 Series User’s Guide...
Page 507: Time And Date
It allows you to specify where the time of the router should be inquired from. Available settings are explained as follows: Item Description Current System Time Click Inquire Time to get the current time. Select this option to use the browser time from the remote Use Browser Time administrator PC host as router’s system time.
Page 508: Snmp
Automatically Update Select a time interval for updating from the NTP server. Interval Click OK to save these settings. This page allows you to configure settings for SNMP and SNMPV3 services. The SNMPv3 is more secure than SNMP through the encryption method (support AES and DES) and authentication method (support MD5 and SHA) for the management needs.
Page 509 character. The default setting is public. The maximum length of the text is limited to 23 characters. Set Community Set community by typing a proper name. The default setting is private. The maximum length of the text is limited to 23 characters. Manager Host IP (IPv4) Set one host as the manager to execute SNMP function.
Page 510: Management
This page allows you to manage the settings for Internet/LAN Access Control, Access List from Internet, Management Port Setup, and CVM Access Control. The management pages for IPv4 and IPv6 protocols are different. Available settings are explained as follows: Item Description Router Name Type in the router name provided by ISP.
Page 511 The web user interface will be open until you click the Logout icon manually. Internet Access Control Allow management from the Internet - Enable the checkbox to allow system administrators to login from the Internet. There are several servers provided by the system to allow you managing the router from Internet.
Page 512 manage Vigor2925. After finished the above settings, click OK to save the configuration. Available settings are explained as follows: Item Description Management Access Allow management from the Internet - Enable the Control checkbox to allow system administrators to login from the Internet.
Page 513: Reboot System
The Web user interface may be used to restart your router. Click Reboot System from System Maintenance to open the following page. Index (1-15) in Schedule Setup - You can type in four sets of time schedule for performing system reboot. All the schedules can be set previously in Applications >> Schedule web page and you can use the number that you have set in that web page.
Page 514: Firmware Upgrade
Note that this example is running over Windows OS (Operating System). Download the newest firmware from DrayTek's web site or FTP site. The DrayTek web site is www.DrayTek.com (or local DrayTek's web site) and FTP site is ftp.DrayTek.com.
Page 515: Activation
After you have finished the setting profiles for WCF (refer to Web Content Filter Profile), it is the time to activate the mechanism for your computer. Click System Maintenance>>Activation to open the following page for accessing http://myvigor.draytek.com. Available settings are explained as follows: Item...
Page 516: Diagnostics
Below shows the successful activation of Web Content Filter: Diagnostic Tools provide a useful way to view or diagnose the status of your Vigor router. Below shows the menu items for Diagnostics. Vigor2925 Series User’s Guide...
Page 517: Dial-Out Triggering
Click Diagnostics and click Dial-out Triggering to open the web page. The internet connection (e.g., PPPoE) is triggered by a package sending from the source IP address. Available settings are explained as follows: Item Description Decoded Format It shows the source IP address (local), destination IP (remote) address, the protocol and length of the package.
Page 518: Routing Table
Click Diagnostics and click Routing Table to open the web page. Available settings are explained as follows: Item Description Refresh Click it to reload the page. Vigor2925 Series User’s Guide...
Page 519: Arp Cache Table
Click Diagnostics and click ARP Cache Table to view the content of the ARP (Address Resolution Protocol) cache held in the router. The table shows a mapping between an Ethernet hardware address (MAC Address) and an IP address. Available settings are explained as follows: Item Description Refresh...
Page 520: Dhcp Table
The facility provides information on IP address assignments. This information is helpful in diagnosing network problems, such as IP address conflicts, etc. Click Diagnostics and click DHCP Table to open the web page. Available settings are explained as follows: Item Description Index It displays the connection item number.
Page 521: Nat Sessions Table
Refresh Click it to reload the page. Click Diagnostics and click NAT Sessions Table to open the list page. Available settings are explained as follows: Item Description Private IP:Port It indicates the source IP address and port of local PC. #Pseudo Port It indicates the temporary port of the router used for NAT.
Page 522: Dns Cache Table
Click Diagnostics and click DNS Cache Table to pen the web page. The record of domain Name and the mapping IP address for answering the DNS query from LAN will be stored on Vigor router’s Cache temporarily and displayed on Diagnostics >> DNS Cache Table.
Page 523: Ping Diagnosis
Click Diagnostics and click Ping Diagnosis to pen the web page. Available settings are explained as follows: Item Description IPV4 /IPV6 Choose the interface for such function. Ping through Use the drop down list to choose the WAN interface that you want to ping through or choose Unspecified to be determined by the router automatically.
Page 524: Data Flow Monitor
Ping IPv6 Address Type the IPv6 address that you want to ping. Click this button to start the ping work. The result will be displayed on the screen. Click this link to remove the result on the window. Clear This page displays the running procedure for the IP address monitored and refreshes the data in an interval of several seconds.
Page 525 Available settings are explained as follows: Item Description Enable Data Flow Check this box to enable this function. Monitor Refresh Seconds Use the drop down list to choose the time interval of refreshing data flow that will be done by the system automatically.
Page 526: Traffic Graph
Click Diagnostics and click Traffic Graph to pen the web page. Choose WAN1/WAN2/WAN3/WAN4 Bandwidth, Sessions, daily or weekly for viewing different traffic graph. Click Reset to zero the accumulated RX/TX (received and transmitted) data of WAN. Click Refresh to renew the graph at any time. The horizontal axis represents time.
Page 527: Trace Route
Click Diagnostics and click Trace Route to open the web page. This page allows you to trace the routes from router to the host. Simply type the IP address of the host in the box and click Run. The result of route trace will be shown on the screen. Available settings are explained as follows: Item Description...
Page 528: Syslog Explorer
Protocol Use the drop down list to choose the protocol that you want to ping through. Host/IP Address It indicates the IP address of the host. It indicates the IPv6 address of the host. Trace Host/IP Address Click this button to start route tracing work. Clear Click this link to remove the result on the window.
Page 529: Ipv6 Tspc Status
Stop record when fulls – when the capacity of syslog is full, the system will stop recording. Always record the new event – only the newest events will be recorded by the system. Time Display the time of the event occurred. Message Display the information for each event.
Page 530: External Devices
You can change the device name if required or remove the information for off-line device whenever you want. When you finished the configuration, click OK to save it. Note: Only DrayTek products can be detected by this function. Vigor2925 Series User’s Guide...
Page 531: Trouble Shooting
This section will guide you to solve abnormal situations if you cannot access into the Internet after installing the router and finishing the web configuration. Please follow sections below to check your basic installation status stage by stage.  Checking if the hardware status is OK or not. ...
Page 532: Checking If The Network Connection Settings On Your Computer Is Ok Or Not
 The example is based on Windows 7. As to the examples for other operation systems, please refer to the similar steps or find support notes in www.DrayTek.com. Open All Programs>>Getting Started>>Control Panel. Click Network and Sharing Center. In the following window, click Change adapter settings.
Page 533 Select Internet Protocol Version 4 (TCP/IP) and then click Properties. Select Obtain an IP address automatically and Obtain DNS server address automatically. Finally, click OK. Vigor2925 Series User’s Guide...
Page 534 Double click on the current used Mac OS on the desktop. Open the Application folder and get into Network. On the Network screen, select Using DHCP from the drop down list of Configure IPv4. Vigor2925 Series User’s Guide...
Page 535: Pinging The Router From Your Computer
The default gateway IP address of the router is 192.168.1.1. For some reason, you might need to use “ping” command to check the link status of the router. The most important thing is that the computer will receive a reply from 192.168.1.1. If not, please check the IP address of your computer.
Page 536: Checking If The Isp Settings Are Ok Or Not
PIN code and try again. If it still fails, it might be the compliance problem of system. Please open DrayTek Syslog Tool to capture the connection information (WAN Log) and send the page (similar to the following graphic) to the service center of DrayTek.
Page 537: Backing To Factory Default Setting If Necessary
Please connect your Notebook with 3G USB Modem to test the connection speed to verify if the problem is caused by Vigor2925. In addition, please refer to the manual of 3G USB Modem for LED Status to make sure if the modem connects to Internet via HSDPA mode. If you want to use the modem indoors, please put it on the place near the window to obtain better signal receiving.
Page 538: Contacting Draytek
After restore the factory default setting, you can configure the settings for the router again to fit your personal request. If the router still cannot work correctly after trying many efforts, please contact your dealer for further help right away. For any questions, please feel free to send e-mail to support@DrayTek.com. Vigor2925 Series User’s Guide...

This manual is also suitable for:

Vigor2925 Vigor2925n Vigor2925n-plus Vigor2925vn-plus Vigor2925f Vigor2925fn

Draytek Vigor 2925 Series User Manual

Quick Links

Related Manuals for Draytek Vigor 2925 Series

Summary of Contents for Draytek Vigor 2925 Series