Making Audio Monitor Signal Settings; Adjusting Playback Audio Levels; Selecting Time Data To Display During Playback; Playback Operations - Sony SRPC-1 Operation Manual

To select the conversion mode
In the VIDEO Setup menu (see page 50), set DC >TYPE
to one of the following.
LB: Letterbox mode
EC: Edge crop mode
When this is selected, you can use DC > POS(EC) to
adjust the H crop (horizontal position of the cropped
sections).
SQ: Squeeze mode
5-3-2 Making Audio Monitor Signal
Settings
The AUDIO Setup menu (see page 52) allows you to make
various settings related to audio monitor signals for
playback.
The procedures are basically the same as those for making
settings related to audio monitor signals for recording.
To adjust the level of audio output to the
EARPHONES jack
Rotate the LEVEL knob.
5-3-3 Adjusting Playback Audio
Levels
The PB LEVEL item in the AUDIO Setup menu (see page
52) allows you to adjust audio levels separately for each
channel.
Note
Playback audio levels cannot be adjusted during recording.
The PB LEVEL settings window appears when you select
the PB LEVEL item. The subsequent procedure is the
same as steps 1 to 5 in "To set recording audio levels"
(page 66).
To set the display range of the audio level
meters
See page 66.
5-3-4 Selecting Time Data to Display
During Playback
Proceed as follows to select the type of time data to display
during playback.
1
Display the TC Setup menu. (See "To display the TC
Setup menu" (page 67).)
2
Select TIMER SEL.
The TIMER SEL settings window appears. (See "To
select the type of time data to display" (page 67).)
3
Rotate the SELECT/ENTER dial to select CTL, TC
(timecode), or UBIT (user bits).
CTL: Display CTL signals recorded on the tape.
TC: Display TC or VITC read by the internal
timecode reader.
The TCR SEL item in the TC Setup menu allows
you to determine whether the timecode reader is to
read LTC or VITC.
UBIT: Display user bit values inserted into the
playback timecode.
4
Press the SELECT/ENTER dial.

5-3-5 Playback Operations

Proceed as follows.
dB
ANLG ANLG SDI SDI SDI SDI SDI SDI SDI SDI A/E
0
-10
HOME
-20
-30
-60
EMP EMP EMP EMP EMP EMP EMP EMP EMP EMP EMP
TC PB
L R L R L R L R L R L R L R L R L R L R L R
1 2 3 4 5 6 7 8 9 10 11
SRW-1
VIDEO OOOO PLAY LOCK
TCR LTC INTRP DF EXT-LK KEYINHI
AUDIO 00 00 00 00
H M S
SYSTEM IN: --:--:--:--
1080 LOCAL
12.2V REMAIN CH.COND
S59P
(29PsF)
46min
4:2:2 21:46
1
Insert the cassette to play back.
For details,"To insert cassettes" (page 39).
2
Press the PLAY button.
Playback starts, and PLAY LOCK appears when the
servos lock.
Press the STOP button to stop playback.
To play back with tracking control
Tracking control can be manually operated or
automatically optimized.
To play back with manual tracking control, use the
following procedure.
1
Insert the cassette to play back and press the PLAY
button.
2
In the SYSTEM Setup menu select SERVO
>TRACKING, and press the SELECT/ENTER dial.
A setting window opens.
5-3 Playback Preparations and Operations
A/E
KEY INHI
OFF ON
SELECT/ENTER
EMP LIGHT
L R
BACK
12
OFF ON
ADJUST
RECINHI
EJECT STOP PLAY REC
Z x B z
F
REW F FWD PAUSE
FUNC
m M X
PB
2
71