S R W; C A S S O U Ttc R - Sony SRPC-1 Operation Manual

To set up the Interval Frame function
1
Perform the procedure in "Common Settings for SR
Motion Shooting" (page 86) to set the target frame
frequency and signal format.
2
Rotate the SELECT/ENTER dial to select "SELECT
FPS" in the submenu window.
A setting window opens.
3
Rotate the SELECT/ENTER dial to select "VTR" and
press the dial.
4
Exit the menu, and press the SELECT/ENTER dial
with the FUNC button held down in the HOME
screen.
The popup window displays the current frame interval
(FRM), the current number of frames (FPS), and the
playback speed.
dB
ANA ANA SDI SDI SDI
0
-10
-20
SR Motion Recording
-30
-60
EMP EMP EMP EMP EMP
SYSTEM
PB
L R L R L R L R L R
SEL-FPS : 59.94P
1 2 3 4
MODE
SIGNAL
OOOO PLAY LOCK
MEMORY
TCG LTC INTRP
FRM
00 00
FPS
10.000
H [ x 2.400 ]
INDLY:
LTC VITC AU
SYS : 1080 S59P(23PsF) 4:2:2
FRM : 8 / 8 F R M ( M O D E : V T R )
MEM : 2 1 %
Playback speed
(times normal playback speed)
Number of frames (FPS)
When you press the SELECT/ENTER dial with the
FUNC button held down and do not perform any
operation for 3 seconds, the screen returns to the
previous state. When you press the SELECT/ENTER
dial with the FUNC button held down and press the
SELECT/ENTER dial again with the FUNC button
held down, the following screen appears. This screen
remains on the display even if you do not perform any
operation for 3 seconds or more.
SDI SDI SDI SDI SDI A/E A/E
EMP EMP EMP EMP EMP EMP EMP
: 23.98PsF
L R L R L R L R L R L R L R
5 6 7 8 9 10 11 12
: VTR
: 6 FRM
*SRW-1
: 21 %
DF EXT-LK KEYINHI
6
RECINHI
FRM
00 00
FPS
M S F
IN: --:--:--:--
50min
12.8V
Frame Interval (FRM)
SR Motion Recording
dB
ANA ANA SDI SDI SDI
0
-10
SYSTEM : 23.98PsF
-20
SEL-FPS : 59.94P
-30
MODE : VTR
-60
SIGNAL : 6 FRM
EMP EMP EMP EMP EMP
MEMORY : 41 %
PB
L R L R L R L R L R
1 2 3 4 5
OO1O REC
TCG
00 02
H
SYS : 1080 S59P(23PsF) 4:2:2
FRM : 8 / 8 F R M ( M O D E : V T R )
MEM : 4 1 %
5
Rotate the SELECT/ENTER dial or ADJUST dial to
select the value of FRM.
The values of FPS and playback speed are displayed
according to the value of FRM.
Note
In the Interval Frame function, the number of frames
cannot be set at steps of 1 FPS, which is different from
the Select FPS function. For example, when you shoot
using a camera of 60P format at 1FRM intervals, the
number of frames is 60 FPS. However, since the next
interval which can be set is 2 FRM, the number of
frames becomes 30 FPS.
To use the Ramp function
The Ramp function allows you to change the frequency
with which frames are captured in Interval Frame
recording, to achieve speed variations.
There are two Ramp modes: manual mode, in which you
specify upper and lower limits and manually vary the
speed within that range, and auto mode, in which you
specify start and end frames and a duration, and allow the
unit to vary the speed automatically according to preset
rules.
Proceed as follows to set up the Ramp function.
1
In the SYSTEM Setup menu, select EDIT >RAMP.
A setting window opens.
S y s t e m S e t u p
FORMAT
REFERENCE
TEST SG
LCD
KEY MAP
KEY INHI MAP
REMOTE/LCKAL LCL
SERVO
REC INHI
OFF
EDIT
POWER
BATTERY
OTHERS
C A S S O U T

S R W - 1

SDI SDI SDI SDI SDI A/E A/E
FRM
6
FRM
FPS
10.000
FPS
EMP EMP EMP EMP EMP EMP EMP
[ x 2.400 ]
L R L R L R L R L R L R L R
6 7 8 9 10 11 12
SRW-1
KEYINHI
RECINHI
11 20
M S F
50min
12.8V
Edit Config
RAMP MANU
Auto Spd1 1
Auto Spd2 20
Duration 5s
Load Curve
Manu Spd1 1
00:00:00:00
TC R
6-1 SR Motion
83