Sony SRPC-1 Operation Manual page 13

Name Pressed alone
PLAY button and Starts playback. (The indicator lights
indicator during playback.)
To start recording, press this button
with the REC button held down.
REC button and Pressing PLAY button with this button
indicator held down starts recording. (The
indicator lights during recording.)
Pressing the button with recording
paused in standby off mode puts the
SRW-1 into standby on mode.
If you press this button during stop, fast
forward, or rewind or when no cassette
is inserted, the SRW-1 enters E-E
mode
E-E signals
OUT A/B connectors or the MONITOR
OUT HD SDI/SD SDI connectors of the
SRPC-1. While an E-E signal is being
monitored, the monitor output format
(see page 37)
seconds.
REW (rewind) button Rewinds the tape. (The indicator lights
and indicator during rewinding, and goes out when
rewinding completes.)
When the REW button is pressed again
during rewinding, the operation
changes to the search mode same as
the button is pressed together with the
FUNC button (searching at the same
speed as searching was stopped
previously).
F FWD (fast forward) Fast forwards the tape. (The indicator
button and indicator lights during fast forwarding, and goes
out when fast forwarding completes.)
When the F FWD button is pressed
again during fast forwarding, the
operation changes to the search mode
same as the button is pressed together
with the FUNC button (searching at the
same speed as searching was stopped
previously).
a)
. In this mode you can monitor
b)
output from the HD SDI
is displayed for a few
Pressed with FUNC button
Pressed with tape transport stopped: Rewinds tape about
5 seconds, and performs playback for about 10 seconds
searching for the recording end position (end search).
Playback stops at the recording end position, or stops
after 10 seconds search if the recording end position is
not detected in the played-back section.
Pressed with recording paused: Plays back the most
recently recorded material, and then returns to recording
pause mode (recording review). When the SYSTEM
>SERVO >REC REVIEW is set to "NORM" (factory
default setting), one press of this button rewinds tape
about 3 seconds and then starts playback. You can keep
the PLAY button pressed together with the FUNC button
to rewind tape as long as the buttons are held down (up
to a maximum of 10 seconds), and then start playback.
Recording review allows you to check whether the
material was recorded correctly.
When the SYSTEM >SERVO >REC REVIEW is set to
"ALL", one press of this button rewinds up to the
beginning of the cut recorded last and then starts
playback.
Note
REC review is not available unless at least 3 seconds have
been recorded.
Temporarily memorizes the time data of the current position
(Mark In).
Mark IN data is displayed in the format "IN: xx:xx:xx:xx" in
the time data field of the display, and can be used for cueup.
Note
The Mark IN data is memorized in the unit's internal memory
only. It is erased when you eject the cassette.
Executes reverse direction searches. With each press, the
search speed changes in the order × 2 t × 5 t × 8 t × 2
normal speed.... If a search is interrupted by another
operation, the next search is performed at the speed in effect
at the time of the interruption.
Note
When using the SRW-1 with 880 Mbps recording rate, × 8
normal speed search is disabled.
For information about recording rate, see FORMAT
>SIGNAL in the SYSTEM Setup menu on page 55.
Executes forward direction searches. With each press, the
search speed changes in the order × 2 t × 5 t × 8 t × 2
normal speed.... If a search is interrupted by another
operation, the next search is performed at the speed in effect
at the time of the interruption.
Note
When using the SRW-1 with 880 Mbps recording rate, × 8
normal speed search is disabled.
For information about recording rate, see FORMAT
>SIGNAL in the SYSTEM Setup menu on page 55.
13
2-1 SRW-1