Sony SRPC-1 Operation Manual page 20

f MONITOR OUT (audio monitor output) L and R
connectors (XLR 3-pin, male)
Output audio monitor signals.
g AES/EBU INPUT CH7/8 and CH9/10 (digital
audio input channels 7/8 and 9/10) connectors
(BNC type)
These connectors allow up to four channels of AES/EBU
format digital audio signals to be input.
Note
The AES/EBU signals must be locked to the video signal.
h AES/EBU OUTPUT CH1-12 (digital audio output
channels 1 to 12) connector (D-sub 15-pin)
Outputs up to 12 channels of AES/EBU format digital
audio signals.
This connector is specially designed for this system. For
details, refer to the Maintenance Manual Volume 1.
i Assist lever
Use this lever when joining or separating the SRW-1 and
SRPC-1.
j EARPHONES jack (stereo minijack) and LEVEL
knob
Use this connector to attach earphones or stereo
headphones equipped with a stereo miniplug, for use in
monitoring audio during recording and playback. Adjust
the audio level with the LEVEL knob.
A warning tone is output to the earphones/headphones
when a warning is lit on the control panel display.
k HD SDI OUT A and B connectors (BNC type)
Output HD SDI video and audio signals.
When the signal format has 720 lines or 1080 lines/30 or
fewer frames, the signals are output from the "A"
connector.
l HD SDI IN A and B connectors (BNC type)
Input HD SDI video and audio signals.
When the signal format has 720 lines or 1080 lines/30 or
fewer frames, input the signals to the "A" connector.
m MONITOR OUT (video monitor output) HD SDI
and SD SDI connectors (BNC type)
Output SDI video and audio signals for monitoring.
HD SDI connector: Outputs HD SDI video and audio
signals for monitoring.
The PD(MON) item in the VIDEO Setup menu (see
page 50) allows you to select whether pull-down
conversion of this output is performed or not.
SD SDI connector: Outputs SD SDI video and audio
signals for monitoring.
Regardless of signal format settings, these connectors
always output signals in 4:2:2 format.
20
2-2 SRPC-1
For more information on output signals, see "Relation
between recording and playback signals and output
signals to video monitors" (page 62) in 5-1-1 "Selecting
the System Signal Format".
VTR operating status and timecode can be superimposed
on the output (see the CHAR(MON) item in the TC Setup
menu (page 48)).
n REF IN (reference signal input) HD and SD
connectors (BNC type)
Input a reference video signal with the correct frame
frequency.
HD connector: As an HD reference video signal, input a
tri-level bipolar sync signal.
SD connector: As an SD reference video signal, input a
video signal with a chroma burst signal (VBS) or black
and white video signal (VS).
When carrying out recording, set REFERENCE >MODE
in the SYSTEM Setup menu to "Input" so that the system
is synchronized with the input video signal.
To record the input video signal in synchronization with an
HD reference video signal, input an HD reference video
signal of the same phase as the input video signal.
Note
When using a reference video signal, its field frequency
must correspond to the system frame frequency set with
FORMAT >FRAME in the SYSTEM Setup menu.
o POWER ON/OFF switch
Powers the SRPC-1 on when pushed up to the ON side. To
power the SRPC-1 off, push the switch down to the OFF
side.
When the SRW-1 is joined to the SRPC-1, this switch
powers both the SRW-1 and SRPC-1 on and off.
p REMOTE IN (remote control input) connector (9-
pin, female)
To use this unit as a playback-side VTR to perform editing
in combination with another HD VTR (e.g. SRW-5500,
etc.) and an editor such as a BVE-700/9100, use a 9-pin
remote control cable (optional) to connect this unit to the
controlling device.
Note
To control this unit from the device connected to this
connector, set REMOTE/LOCAL in the SYSTEM Setup
menu (see page 57) to RMT.
q CAMERA REMOTE IN (remote control input)
connector (8-pin)
When the optional HKSR-101 Optical Interface Unit is
installed, you can connect an RM-B750/B150 Remote
Control Unit to this connector.