Yamaha SY85 Owner's Manual page 406

Bn 00 xx 20 xx
Card2 Voice(multi)
Card3 Voice(multi)
Card4 Voice(multi)
Internal1 Perf(multi)
Internal2 Perf(multi)
Card1 Perf(multi)
Card2 Perf(multi)
When the mode is set to off the program change is not transmitted.
When the mode is set to table the conversation formal contained in the program transmission table is
applied and transmitted.
1.2.1.5 Program change
Program change is transmitted, when a voice is selected in voice mode, when a performane is
selected in performance mode.
Program change No. is asigned as shown below in accordance with the mode.
Voice Internal1
Internal2
Internal3
Internal4
Card1
Card2
Card3
Card4
Performance
Internal1
Internal2
Card1
Card2
When the mode is set to off the program change is not transmitted.
When the mode is set to table, the conversion format contained in the program transmitssion table is
applied and transmitted.
1.2.1.6 Pitch bend
Pitch bend is transmitted with a resolution of 7 bits.
1.2.1.7 After touch
After touch is output when it is operated.
1.2.1.8 Channel mode message
Channel mode message is not transmitted.
1.2.2 Reception
1.2.2.1 Note Off
Reception note range
Velocity range
1.2.2.1 Note On/Off
Reception note range
Velocity range
1.2.2.2 Control Change
The parameters in the table below can be controlled by MIDI.
parameter
c n t r l #
Modulation wheel
1
4 Foot control
Foot Volume
7
10 Pan
0 ~ 1 1 9 Volume
1 ~ 1 2 0 Effect Param1
1~120 Effect Param2
16~19 CS Param
64 Sustain Switch
Pan is received only when MULTI is generated.
Data
00,36
00,39
00,42
00,80
00,83
00,81
00,84
Data
0 ~ 6 3 00~63
0 ~ 6 3 00~63
0 ~ 6 3 00~63
0 ~ 6 3 00~63
0 ~ 6 3 00~63
00~63
0 ~ 6 3
00~63
0 ~ 6 3
00~63
0 ~ 6 3
00~63
0 ~ 6 3
0 ~ 6 3 00~63
00~63
0 ~ 6 3
0 ~ 6 3 00~63
= C - 2 ~ G 8
= not received.
= C - 2 ~ G 8
= 0 ~ 1 2 7
data mg
0 ~ 1 2 7
0 ~ 1 2 7
0 ~ 1 2 7
0 ~ 1 2 7
0 ~ 1 2 7
0 ~ 1 2 7
0 ~ 1 2 7
0 ~ 1 2 7
0, 127
1.2.2.3 Program change
When a program change message is received, the SY85 performs the following operations.
Three types of reception modes can be set with the system setup.
1) off:
Program change is not received.
2) normal:
In each play mode, the program No. changes in accordance with 00 ~ 63 of the current
mode.
The program bank change is not received.
3) direct:
In voice mode, voice A1 ~ H8 correspond to the program change data 00 ~ 63. INT1,
INT2 and CARD change in accordance with the program bank change.
Program change data 64 ~ 127 is not received. In performance mode, performance A1 ~
H8 correspond to program change data 00 ~ 63. Int1, Int2, and CARD change in accor
dance with the program bank change.
Program change data 64 ~ 127 are not received.
In Multi mode, each INST program changes in accordance with the above.
Refer to during transmission for the bank change.
4) table:
Reception applies to 3) direct.
Transmission is carried out in accordance with the PROGRAM CHANGE TABLE.
1.2.2.4 Pitch bend
Pitch bend is received only on the MSB side.
1.2.2.5 After touch
After touch is received in accordance with the reception channel of each mode.
1.2.2.6 Channel mode message
cntrl#
120
121
123
1.2.3 Configuration of keyboard section and tone generator
Note 1) In voice mode, sound is generated even if the Voice receive channel and the Keyboard Trans,
channel do not match.
Note 2) Note On from the keyboard and Note On from MIDI are distinguished. Controller information
from the keyboard and controller information from the MIDI (control change, after touch, pitch
bend, etc.) are not distinguished except for sustain switch.
2
parameter data mg
All Sound Off 0
Reset All Controller 0
0
All Notes Off