Related Manuals for Vision 1480 Series
Summary of Contents for Vision 1480 Series
- Page 1 series 1480 DIGI LINK SMART FAC TORY KEYL ESS UPGRADE SECURIT Y © 2 0 1 1 - 2 0 1 4 K I R A M E K , I N C . , A i c h i J a p a n V er .
- Page 2 Thank you for purchasing this VISION 1480 Vehicle Security System. The 1480 is a state of the art device that will pro- vide you with years of trouble free ser- vice if used properly. Please familiarize yourself with the content of this Owner’s Guide to get the most out of your new system.
-
Page 3: Table Of Contents
TABL E OF CONTENTS Limited Lifetime Warranty ........Included Items ..........Arming & Disarming ........Arming ..........Confirmation Chirps ........Disarming ..........Manual Disarming ........Main Features ..........Trunk Release Bypass ........Door Trigger ........... 2-Stage Shock Sensor ........Ignition Trigger ......... -
Page 4: Limited Lifetime Warranty
Authorized VISION Dealer. All product warranties become void if the VISION 1480 system was not sold and installed by an Authorized VISION Dealer or the sys- tem is moved to another vehicle. All other parts and/or accessories that... -
Page 5: Included Items
INC L UDED ITEMS Control Module (1pc) Shock Sensor (1pc) LED Program Sw. (1pc) Only 1480B includes keys. Siren (1pc) Control Mod. Harnesses (2pcs) Sensor Harness (1pc) Sensor Tape (1pc) Window Decals (2pc) Guides (2pc) Dark RED (p/n NL-1) (p/n NT-4) 25cm Wire Ties (2pcs) PosiTap Connectors (4pcs) PosiLock Connector (1pc) -
Page 6: Arming & Disarming
Arming & disarming ARMING NORMAL ARMING LOCK Close all doors and then LOCK by your factory keyless remote or by SmartKey door handle touch. ON). The Status LED will light for 5s, during which time all triggers are disabled. Then the Status LED triggers become enabled. -
Page 7: Disarming
arming & disarming DISARMING NORMAL DISARMING UNLOCK UNLOCK by your factory keyless remote or by SmartKey door handle touch. Vehicle hazard will chirp 3 times and the Status LED will turn off. The 1480 is now Disarmed and you may enter the vehicle. If the siren chirps 4 times when you Disarm, it means something had trig- gered while you were away from the vehicle. -
Page 8: Manual Disarming
ARMING & DISARMING MANUAL DISARMING You can manually Disarm using a secure code in the event your factory remote’s battery dies (see Note 2 below). The factory set code is “6”, but you can change this code to another number of your choosing for greater security (see the bottom of this page). -
Page 9: Main Features
MAIN FEATURES TRUNK RELEASE BYPASS TRUNK For cars that support it, pressing the Trunk Release button on the factory remote will bypass the shock sensor and trunk triggers while the trunk opens. Door and Ignition switch triggers remain active, and doors remain locked. Five (5) seconds after you close the trunk, the shock sensor and trunk triggers will be automatically re-activated. -
Page 10: Ignition Trigger
MAIN FEATURES IGNITION TRIGGER PROGRAMMABLE IG PROTECT MODE (default) IG ON IG ON The siren will blast for 30 seconds when the Ignition (IG) switches ON while the system is (To Disarm and stop the siren, turn off the Ignition and then press Unlock on the factory remote.) REMOTE START COMPATIBILITY MODE (RSCM) (user-programmable) When the Ignition switches ON while Armed in this... -
Page 11: Hood Trigger
MAIN FEATURES HOOD TRIGGER On compatible vehicles (or on any vehicle when the op- tional analog Hood input is connected), the siren will blast for 30 seconds when the hood is opened while the ERROR CHIRP If a Door or the Trunk is open when you Lock/Arm, you will hear 1 chirp 2 chirps mation Chirps are OFF). -
Page 12: Status Led
MAIN FEATURES STATUS LED slowly about once per second while the system is Armed, acting as a visual theft deterrent. The LED turns off when the system is Disarmed, unless there was a siren trigger. TRIGGER MEMORY rapidly while the full siren blast is going off and Table-1 below, showing you what triggered the siren. -
Page 13: Hazard Flash
MAIN FEATURES HAZARD FLASH times (depending on the car) when shock sensor Warning Chirps are trig- RESUME RESUME is a form of State Memory that remembers if the system was Armed or Disarmed when the main power is cut. When power is restored, the 1480 will power-up Disarmed if it was disarmed in its previous state. -
Page 14: Programmable Features
PROGRAMMABL E FEATURES You can change some features of the 1480 by using the Program Switch. Perform the following 4-step procedure to change the fea- tures shown in Table-2: 1. Start the engine and then Stop the engine. 2. With the Ignition OFF, Arm the 1480 and then immediately Disarm. 3. - Page 15 PROGRAMMABL E FEATURES Ignition Trigger You cannot Arm if IG is ON in IG Protect Mode When set to (default), the system will trigger the siren IG Protect Mode when the Ignition (IG) turns ON while Armed, as described on page 7. When set to , the system will by- RSCM (Remote Start Compatibility Mode)
- Page 16 PROGRAMMABL E FEATURES Auto Rearm This feature automatically Rearms the system 60s after it is Disarmed, unless a Door is opened or the Ignition goes ON during the 60s. Doors will be locked when the system Rearms. Speed Controlled Door Locking When set to , the Doors will Auto-Lock when the vehicle speed reaches P (Park) position, the Doors will Auto-Unlock.
-
Page 17: Troubleshooting
TROUBL ESHOOTING FACTORY KEYLESS REMOTE WAS LOST, DISARMING If the factory remote was lost, you may not be able to Disarm if you have a Push Start car that requires the factory remote to turn on the Ignition. In such a case, you must to contact your dealer for a replacement factory remote. - Page 18 TROUBL ESHOOTING CANNOT DISARM WHILE THE SIREN IS SOUNDING Ensure all doors & trunk are closed, then try to Unlock to Disarm. • • SHOCK SENSOR 1st STAGE “WARNING” TRIGGER DOESN’T WORK Examine the shock sensor and look closely at the two LEDs. If you never see Green light, adjust the sensitivity knob on the sensor.
-
Page 19: Options
OP TIONS The 1480 can be installed in your car without the need for any Options. However, we do offer the following add-on products to enhance security and convenience: TR537S: 2-way LCD RF Paging Control System (ARIB-T67, for Japan) TR835S: 2-way LCD RF Paging Control System (FCC, for USA) 896H-1B: Starter Kill Relay 896H-1CN: Relay to drive high-current devices like the Horn. - Page 20 VISION products are engineered in Japan and manufactured in strict accordance with Japanese QC standards at an ISO9000/ QS9000 certified factory. 9 - 1 8 3 - 1 I t a y a m a - c h o , H a n d a - s h i , A i c h i - K e n 4 7 5 - 0 9 3 6 J A P A N...
- Page 21 series 1480 DIGI LINK SMART FAC TORY KEYL ESS UPGRADE SECURIT Y © 2 0 1 1 - 2 0 1 4 K I R A M E K , I N C . , A i c h i J a p a n V er .1 .5 , AP R.4 ,2 0 1 4...
- Page 22 INSTALLERS, READ THIS MANUAL THOROUGHLY! The 1480 must be connected by an experienced VISION installer. All product warranties im- mediately become void if the 1480 is not in- stalled by an authorized dealer. If you acquired this product without profes-...
- Page 23 TABL E OF CONTENTS Precautions & Safety ........Installation Tips ........... Technical Specifications ........Included Items ..........Read This First ..........System Wiring Diagram ........OBD Connector ........... Power & CAN Connections ........Siren Connections ........Siren Setup ..........Optional Connections ........
-
Page 24: Precautions & Safety
Prec autions & Safety OPERATION Use of the 1480 outside its intended purpose, as described in this Install Guide and the 1480 Owner’s Guide, could result in damage to the vehicle or surrounding property, or cause serious injury or even death. As the installer of this security system, it is your responsibility to ensure that the vehicle owner is properly informed of all the details of your instal- lation which are pertinent to safety. -
Page 25: Installation Tips
Insta l l ation Tips Steps Toward a Professional Installation: • Ensure all electrical contacts cannot easily break by tugging on the wires. Use the included 4 PosiTap connectors when connecting to vehi- cle CAN wires and Power wires. Use the included and PosiLock connec- tor when connecting to the Siren. -
Page 26: Technical Specifications
Technic al Specific ations Control Module Operating Voltage: 12Vdc Current Consumption: 3.3mA (Armed* w/ LED flashing) 2.0mA (Disarmed or Armed* in Sensor Bypass Mode) (Does not include Shock Sensor consumption) Operating Temp.: -40°C to +85°C Certification: IP40 * While vehicle CAN sleeping Shock Sensor Operating Voltage: 12Vdc... -
Page 27: Included Items
INC L UDED ITEMS Control Module (1pc) Shock Sensor (1pc) LED Program Sw. (1pc) Only 1480B includes keys. Siren (1pc) Control Mod. Harnesses (2pcs) Sensor Harness (1pc) Dark RED (p/n NL-1) (p/n NT-4) 25cm Wire Ties (2pcs) PosiTap Connectors (4pcs) PosiLock Connector (1pc) Sensor Tape (1pc) Window Decals (2pc) -
Page 28: Read This First
READ THIS FIRST ALARM FIRMWARE & ONE-TIME LEARNING FIRMWARE This product only works on select cars that have a compatible digital CAN- BUS communication system. If your car is not on our compatibility list, this 1480 product will not function at all! We do not accept product returns due to CAN-BUS data mismatching, so make absolutely sure prior to purchase CAN has been programmed into the 1480 product (by your authorized VI- SION dealer or by our company, KIRAMEK, Inc.) Visit our website for the... -
Page 29: System Wiring Diagram
SYSTEM WIRING DIAGRAM Two connectors on back are for firmware programming only. Harness Program Switch Optional Pager Shock Sensor Main Harness ( + ) 12v Siren Output (2A) (–) GWA Output (500mA) (–) Ground Input (–) Hood Switch Input Fuse ( + ) 12v Power Input CAN - L CAN - H... -
Page 30: Obd Connector
OBD CONNEC TOR PURPOSE An OBD2 connector is included with most 1480 systems, and the following 4 wires are already connected to it: 2) (–) Ground Input 3) CAN-H 4) CAN-L Toyota, Lexus and Nissan cars allow you to merely connect the OBD2 plug to your car’s OBD2 connector, and then you need only connect the BROWN wire to the Siren (plus any optional connections —... - Page 31 OBD CONNEC TOR Wire Tie Wires exiting RIGHT side Wires exiting LEFT side Wrap wires around PCB to the right CONNECTING THE OBD PLUG (–) GND CAN-H Pin4 Pin6 On TOYOTA, LEXUS and NISSAN cars, connecting is as simple as shown at right.
-
Page 32: Power & Can Connections
power & c an connec tions NOTE Pages 9-10 describe how to MANUALLY CONNECT the Power & CAN wires. You do not need to reference these 2 pages if you have a Toyota, Lexus or Nissan car, unless you wish to cut off the OBD plug and make your connections manually. - Page 33 power & c an connec tions CAN-L CAN HARNESS The BROWN wire is a digital I/O line that must be con- nected to the car’s CAN-LOW line. CAN-L is Pin-14 of CAN-L the car’s OBD connector on all Toyota, Lexus and Nissan cars.
-
Page 34: Siren Connections
SIREN CONNEC TIONS ( + ) 12v Siren Output during a security breach. Do not confuse this wire with the Brown wire of the CAN harness! The way to connect the Brown SIREN wire depends on which version of siren you have. The 1480S comes with a standard 2-wire siren (see Fig-1 below). -
Page 35: Siren Setup
siren setup NOTE We strongly suggest you avoid connecting the siren’s RED or BLACK wires in parallel with the Power & Ground wires of the 1480. For ex- ample, if you splice Power/Ground off the OBD plug, it may cause a voltage drop malfunction in the alarm system. -
Page 36: Optional Connections
OP TIONAL CONNEC TIONS (–) GWA Output OPTIONAL PARTS REQUIRED GWA stands for Ground-When-Armed. This wire supplies (–) Ground (500mA max.) while the 1480 is Armed. One common use is for connection to an optional 896H-1B starter kill relay as shown in Fig-3 below. 896H-1B IGNITION STARTER... -
Page 37: Can Signal Learning
C AN SIGNAL L EARNING matched to your car. The 1480 will be completely disabled until you com- plete the steps below. You only need to do it once. NOTE Performing this initial setup procedure automatically resets all func- tions to their factory defaults. This includes a reset of the Program- mable Features (Owner’s Guide page 11), and resets any custom Manual Disarm Code you may have programmed (Owner’s Guide page 5). -
Page 38: Mounting System Components
MOUNTING SYSTEM COMPONENTS Control Module The Control Module is “the brain” of the system and therefore must be installed in a secure location under the dash. NEVER install the Control Module in the engine compartment or near any source of heat or moisture! NEVER place the Control Module near moving parts or in a location where it can vibrate or move around excessively. - Page 39 MOUNTING SYSTEM COMPONENTS Shock Sensor The shock sensor is not waterproof so only mount it inside the car. Only use the included 2-sided tape, and mount the sensor to the outside of a plastic surface such as the car’s center console. We recommend you mount it in open view (rather than hide it) in order to make sensitivity adjust- ments easier.
-
Page 40: Adjusting The Shock Sensor
False Alarms The VISION 318-052 Active-IR shock sensor has been engineered to avoid false triggers in most situations. However, there is still the possibility the sensor could trigger the siren during a strong earthquake, jackham-... -
Page 41: Troubleshooting
TROUBL ESHOOTING CAN LEARNING NOT SUCCESSFUL. If you manually connected Power and CAN (pages 9-10) instead of us- • CAN-L are reversed, you of course will not be able to learn the vehicle’s CAN signals. Also note that the vehicle’s CAN wires are normally a “twisted”... - Page 42 • for, the alarm may function correctly sometimes but not at other times. Tool required, or visit your VISION dealer.) SHOCK SENSOR ONLY “FULL TRIGGERS.” THERE’S NO WARNING TRIGGER. View the sensor’s LEDs when you hit the car’s body. If the Green LED •...
-
Page 43: Options
OP TIONS The 1480 can be installed in your car without the need for any Options. However, we do offer the following add-on products to enhance security and convenience: TR537S TR835S: 2-way LCD RF Paging Control System (FCC, for USA) 896H-1B: Starter Kill Relay 896H-1CN: Relay to drive high-current devices like the Horn. - Page 44 VISION products are engineered in Japan and manufactured in strict accordance with Japanese QC standards at an ISO9000/ QS9000 certified factory. 9 - 1 8 3 - 1 I t a y a m a - c h o , H a n d a - s h i , A i c h i - K e n 4 7 5 - 0 9 3 6 J A P A N...