Download Print this page

Section 5. Filter Disassembly And Assembly; Section 6. Maintenance; General Maintenance - Jandy CL Versa-Plumb Series Installation And Operation Manual

Cartridge pool filters
Hide thumbs

Advertisement

"T" Nut
Clamp
Ring
Clamp Ring,
Closed Position
Figure 10. Filter Clamp Ring Assembly
9.
After the pressure gauge has stabilized, turn the
bezel ring so that the arrow next to the word
"CLEAN" aligns with the needle of the gauge. As
the fi lter cleans the water, and the cartridges begin
to clog the pressure begins to increase. When the
needle of the pressure gauge aligns with the arrow
next to the word "DIRTY" on the bezel, it is time
to clean the fi lter (see Section 6.3). This indicates
an increased pressure of between 10 and 12 psi
above original starting pressure.
Section 5. Filter Disassembly and
Assembly
WARNING
NEVER attempt to assemble,
dis as sem ble or adjust the filter when
there is pressurized air in the system.
Starting the pump while there is any
pressurized air in the system can
cause product failure or also cause
the filter lid to be blown off, which can
cause death, serious personal injury
or property dam age.
1.
Turn off the pump. Switch off the circuit breaker
to the pump motor.
Cartridge Pool Filters - CL and CV Series Filters
Thread ed
Tightening
Rod
Nut w/
Shoulder
Tightening
Nut w/
Shoulder
Use a 9/16" Socket
GAP NOT TO EXCEED
1/16"
2.
IMPORTANT: Completely open air release valve
on top of the fi lter tank to release all pressure
from inside the tank and system.
3.
If the equipment is installed below water level,
close the fi lter isolation valves on the system to
prevent fl ooding.
4.
Remove the drain plug located at the bottom of the
fi lter tank and allow the tank to drain.
5.
Replace the drain plug.
6.
Loosen the tank clamp ring retainer and remove
the clamp ring.
7.
Remove the top of the fi lter tank by lifting it
straight up until it clears the cartridges on the
inside of the tank.
8.
Remove the manifold assembly by lifting it off of
the outlet tube and out of the tank.
9.
Pull the cartridges out of the fi lter tank and clean
the cartridge using the instructions in Section 6.3.
10. Using new cartridges or the clean original ones,
place the cartridges back into the fi lter tank. Be
sure that they are correctly seated on the cartridge
support on the bottom of the tank.
11. Inspect the o-ring at the top of the outlet tube for
cracks and wear marks. Replace if necessary.
12. Reinstall the manifold making sure that it fi ts
squarely over the cartridges and outlet tube.
13. Inspect the tank o-ring for cracks or wear marks.
Replace if necessary. Place the o-ring back onto
the fi lter bottom.
14. Place the fi lter lid onto the fi lter tank bottom.
15. Replace the tank clamp ring. See Section 3.5 for
clamp installation.
16. If applicable, open the valves closed in step 3.
17. Start the pump by following the procedures
outlined in steps 2 through 7 of Section 4.

Section 6. Maintenance

6.1 General Maintenance

1.
Wash outside of fi lter with a mild detergent and
water. Rinse off with a hose. Do not use solvents
to clean the fi lter, solvents will damage the plastic
components of the fi lter.
2.
Check pressure during operation at least once a
week.
3.
Remove any debris from the skimmer basket and
hair/lint pot on pump.
4.
Check pump and fi lter for any leaks. If any leaks
develop, turn off the pump and call a qualifi ed
pool service technician.
Page 11

Advertisement

loading

  Related Manuals for Jandy CL Versa-Plumb Series