Timescan Audio - JVC HR-S9600EK Instructions Manual

TimeScan
Names of
special-effects
playback
-9x
Speed SP
Speed LP
Audio output
** To activate the Still mode from the remote control press PAUSE button. Still mode cannot be engaged
using the remote control's
** Smooth slow motion delivering an uninterrupted moving image without distortion.
If the picture jitters vertically, noise appears or the upper or lower part of the picture is distorded at -1/2x, -1/3x, 1/3x, 1/2x or
1.5x normal speed, use TV PROG + or – to correct the picture.
Noise tends to appear at -9x or 9x normal speed during TimeScan search.
When noise appears or the upper or lower part of the picture is distorted during TimeScan search, press
tracking with TV PROG + or – button.
The speed is shown during TimeScan in the upper right corner of the TV screen for approx. 5 seconds. (On some TVs the
display may be distorted.)
To resume normal playback, press PLAY.
Picture and audio may occasionally become distorted when the recording speed changes. If this happens, resume normal
playback once, and then try using TimeScan again.
The picture may be noisy or there may be a loss of colour when you change the playback speed. (More noise will appear with
LP recordings.)
Noise may appear or the upper part of the picture may be distorted during still, frame-by-frame playback, 2x search of LP
recordings, or with certain tapes.
Picture may appear distorted in comparison to normal playback.
When normal playback resumes from search (including TimeScan), still, slow motion or frame-by-frame playback, the picture
may jitter vertically momentarily depending on the type of TV being used.
Depending on the tape in use, noise may appear or the upper part of the picture may be distorted.
In TimeScan mode there will be a time lag between the video and the audio and noise may appear in the audio signal.
TimeScan sound quality will differ in comparison to normal playback.
When material such as music videos where there is non-stop sound (very few breaks in the soundtrack) are viewed at 1.5x or
2x normal speed, the audio playback may be faster than normal.
Depending on the type of tape contents, the sound may not be clear during forward slow-motion playback.
Time Jog cannot be activated by pressing PAUSE for longer than 2 seconds.
When the playback direction is reversed, it takes approximately 6 seconds until sound is heard.
TimeScan does not work with NTSC playback.
The operations by JOG dial/SHUTTLE ring do not include TimeScan; noise will appear on the screen and audio will not be
output.
If you don't want to hear TimeScan audio, set the "TIME SCAN AUDIO" to OFF. (See below)

TimeScan Audio

The audio output can be set ON/OFF during TimeScan. Select ON/OFF as required.
* The default setting is "ON".
1 Press MENU to access the Main Menu screen.
2 Move the highlight bar (pointer) to "MODE SET" by pressing %fi, then press OK or
3 Move the highlight bar (pointer) to "TIME SCAN AUDIO" by
pressing %fi, then press OK or
4 Press MENU to return to the normal screen.
Reverse
Search Play
-7x -5x -3x -1x
-7x -3x
Audio is output.
@ #
#
to select "ON" or "OFF".
Slow-Motion
*Still
(Time Jog**)
-1/2x -1/3x 0
-1/2x 0
Audio is not Audio is
output. output.
button.
MODE SET
B. E. S. T.
PICTURE CONTROL
AUTO TIMER
O. S. D.
DIRECT REC
AUTO SP=LP TIMER
DIGITAL 3R
NEXT PAGE
[5∞] =
[MENU] : EXIT
Forward
Slow-Motion
Play
(Time Jog**)
1/3x 1/2x 1x 1.5x 2x 3x 5x 7x 9x
1/2x 1x 1.5x 2x
Audio is
Audio is output.
output.
#
.
PREVIOUS PAGE
POWER SAVE
ON
S-VHS
AUTO
AV1 SELECT
OFF
AV2 SELECT
ON
ON TIME SCAN AUDIO
OFF
ON
[5∞] =
[MENU] : EXIT
27
Search
5x 9x
and adjust
OFF
AUTO
VIDEO
AV2
ON