※ 505R/IP505R/SR505 QUICK INSTALLATION GUIDE 1. IMPORTANT SAFETY INSTRUCTIONS The description below is to keep user‟s safety and prevent any product damage. Please fully read these instruction and use the product properly. Danger: This symbol indicates that incorrect handling of the product may result in serious injury or death.
※ 505R/IP505R/SR505 QUICK INSTALLATION GUIDE 2. WHAT’S INCLUDED Please unpack and check the contents of the box. If any of these parts are missing, please contact a nearby distributor or IDTECK. Main Unit Wall Mount O-ring User’s Manual (1ea) (1ea)
3LEDs: ○ When the power is supplied to Star 505R, the red LED is turned on. When the Relay #1 is operated, the green LED is turned on. When the Relay #2 is operated, the yellow LED is turned on.
Page 5
Initialization Switch ○ This switch is used to initialize Star 505R. For initialization, press down this switch and then keep it more than 2 seconds. Refer to „8.2 System Initialization‟ of the main manual for more details. Communication Display LED ○...
Page 6
※ 505R/IP505R/SR505 QUICK INSTALLATION GUIDE 3.3 Connection and Color Code Table CON6 CON4 CON3 CON2 CON5 CON7 IO PORT NAME SIGNAL NAME COLOR CODED POWER CON7 Main Power(+12V) DC +12V Power Ground Black OUTPUT CON4 Door Relay(COM) COM(1) Gray with Red Stripe Door Relay(NC) NC(1) Blue with White Stripe...
Reference Description Cable Specification Distance Star 505R Power (DC12V) Belden #9409, 18 AWG ① DC Power -> Star 505R 2 conductor, unshielded Belden #9512, 22 AWG 4 conductor, shielded Reader (Power and Data) 150m ② Extra Reader -> Star 505R...
Real size template is on back of this manual. Tear off the template page and attach it to the wall. And then follow steps below to install the Star 505R. (You can install the Star 505R directly, if the gang box is installed on the wall.) 1.
Page 10
INITIALIZATION‟ of the main manual) 6. Insert O-ring at 5 positions and then insert the bundle of cable to the center hole. 7. Put the Star 505R unit on the wall mount and push it until it is fixed up. CAUTION ※...
You have to initialize the Star 505R unit prior to installation. Once power is supplied to the Star 505R, press down the initialization switch on the back of the Star 505R unit and then keep it more than 2 seconds, then you can see displays below on the LCD. If you want initialization, press key <1>...
Page 12
505R/IP505R/SR505 QUICK INSTALLATION GUIDE 5.3 WIRING 5.3.1 Power Connect (+) wire of DC +12V power to the DC +12V (Red wire) of Star 505R. Connect GND (-) wire of DC +12V power to the GND (Black wire) of Star 505R. 5.3.2 Input Connection Exit Button Connection - Connect one wire from an Exit Button to the Orange wire.
Page 13
※ 505R/IP505R/SR505 QUICK INSTALLATION GUIDE 2.2K Resistance Connection for Cut Off Check You have to connect a 2.2K Resistor between the input wire (e.g. Orange wire) and the GND to apply the Cut Off Check feature. First, select whether or not to check the Cut Off status of each device from “F2 SETUP MENU” -> “5. IN/OUT DEFINE”->...
Page 14
SR505: Standard 34bitWiegand Format Proximity Readers. Standard 34bitWiegand+8bit Burst Format Proximity and Keypad Readers. Recommended Readers: Star 505R/IP505R: RF-TINY, RF10, RF20, RF30, RFK101, FGR006, FGR006EX, iP10, iP20, iP30, iPK101. SR505: SR10, SR20, SR30, SRK101, FGR006SR, FGR006SRB. Figure: Star 505R/Reader Connection...
Please follow the instructions below: - Connect RS232-TX (Black wire with White stripe) port of Star 505R to the PIN 2 of the 9-PIN connector. - Connect RS232-RX (Red wire with White stripe) port of Star 505R to the PIN 3 of the 9-PIN connector.
Figure: Multiple connections of Star 505Rs 6.3 TCP/IP Communication Port Connection (optional) Optional TCP/IP module is required to use TCP/IP communication between the Star 505R and the PC. Please follow the following instructions below: 1. Connect the LAN cable of the network system to the RJ45 jack of the Star 505R.
7.2 Entering Setup Mode To setup or to change the Star 505R settings, you have to enter the Setup Mode first. To do so, enter the Master ID (default=00000000)* and press the <ENT> key. There are 4 main Setup menus and you automatically get into “SETUP MENU F1”...
Page 18
7.4 Setting Maximum Number of Cardholder IDs You can set the maximum number of cardholder IDs that can be registered on the Star 505R. By default, the Star 505R is set to store up to 10,000 cardholders and 50,000 events and you can adjust this setting to increase the cardholder capacity at the expense of event memory.
8.2 Default Setting When you operate the Star 505R first time or you initialize the Star 505R, the controller will set up all values to default settings (Factory Settings). You can change the settings for desired application. Please refer to the...