Cisco TelePresence Administrator's Manual page 453

Reference material
Command reference — xConfiguration
Zones LocalZone SubZones MembershipRules Rule [1..3000] Name: <S: 0,50>
Assigns a name to this membership rule.
Example: xConfiguration Zones LocalZone SubZones MembershipRules Rule 1 Name: "Office Workers"
Zones LocalZone SubZones MembershipRules Rule [1..3000] Pattern String: <S: 0,60>
Specifies the pattern against which the alias is compared.
Example: xConfiguration Zones LocalZone SubZones MembershipRules Rule 1 Pattern String: "@example.com"
Zones LocalZone SubZones MembershipRules Rule [1..3000] Pattern Type: <Exact/Prefix/Suffix/Regex>
The way in which the pattern must match the alias.
Example: xConfiguration Zones LocalZone SubZones MembershipRules Rule 1 Pattern Type: Suffix
Zones LocalZone SubZones MembershipRules Rule [1..3000] Priority: <1..65534>
Determines the order in which the rules are applied (and thus to which subzone the endpoint is assigned) if an endpoint's address
satisfies multiple rules. The rules with the highest priority (1, then 2, then 3 and so on) are applied first. If multiple Subnet rules have
the same priority the rule with the largest prefix length is applied first. Alias Pattern Match rules at the same priority are searched in
configuration order. Default: 100.
Example: xConfiguration Zones LocalZone SubZones MembershipRules Rule 1 Priority: 100
Zones LocalZone SubZones MembershipRules Rule [1..3000] State: <Enabled/Disabled>
Indicates if the membership rule is enabled or disabled. Disabled membership rules are ignored. Default: Enabled.
Example: xConfiguration Zones LocalZone SubZones MembershipRules Rule 1 State: Enabled
Zones LocalZone SubZones MembershipRules Rule [1..3000] SubZoneName: <S: 0,50>
The subzone to which an endpoint is assigned if its address satisfies this rule.
Example: xConfiguration Zones LocalZone SubZones MembershipRules Rule 1 SubZoneName: "Branch Office"
Zones LocalZone SubZones MembershipRules Rule [1..3000] Subnet Address: <S: 0,39>
Specifies an IP address used (in conjunction with the prefix length) to identify this subnet.
Example: xConfiguration Zones LocalZone SubZones MembershipRules Rule 1 Subnet Address: "192.168.0.0"
Zones LocalZone SubZones MembershipRules Rule [1..3000] Subnet PrefixLength: <1..128>
The number of bits of the subnet address which must match for an IP address to belong in this subnet. Default: 32.
Example: xConfiguration Zones LocalZone SubZones MembershipRules Rule 1 Subnet PrefixLength: 32
Zones LocalZone SubZones MembershipRules Rule [1..3000] Type: <Subnet/AliasPatternMatch>
The type of address that applies to this rule.
Subnet: assigns the device if its IP address falls within the configured IP address subnet.
AliasPatternMatch: assigns the device if its alias matches the configured pattern.
Example: xConfiguration Zones LocalZone SubZones MembershipRules Rule 1 Type: Subnet
Zones LocalZone SubZones SubZone [1..1000] Authentication Mode:
<DoNotCheckCredentials/TreatAsAuthenticated/CheckCredentials>
Controls how the VCS authenticates incoming messages from this subzone and whether they are subsequently treated as
authenticated, unauthenticated or are rejected. The behavior varies for H.323 messages, SIP messages that originate from a local
domain and SIP messages that originate from non-local domains. See the Administrator Guide for further information. Default:
DoNotCheckCredentials.
Example: xConfiguration Zones LocalZone SubZones SubZone 1 Authentication Mode: DoNotCheckCredentials
Zones LocalZone SubZones SubZone [1..1000] Bandwidth PerCall Inter Limit: <1..100000000>
The bandwidth limit (in kbps) on any one call to or from an endpoint in this subzone (applies only if Mode is set to Limited). Default:
1920.
Example: xConfiguration Zones LocalZone SubZones SubZone 1 Bandwidth PerCall Inter Limit: 1920
Cisco VCS Administrator Guide (X8.1.1) Page 453 of 507