Cisco TelePresence Server MSE 8710 Getting Started
Hide thumbs
Also See for TelePresence Server MSE 8710:
- Installation manual (12 pages) ,
- Help manual (92 pages) ,
- Help manual (132 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Installation Manual
Advertisement
Table of Contents
Related Manuals for Cisco TelePresence Server MSE 8710
Summary of Contents for Cisco TelePresence Server MSE 8710
- Page 1 Cisco TelePresence Server MSE 8710 Getting started 61-0025-04...
-
Page 2: Table Of Contents
Front panel LED behavior ..................4 Installing the Cisco TS MSE 8710 ..................5 Step one: Install the Cisco TS MSE 8710 blade into the MSE 8000 .... 5 Step two: Allocate port licences ................7 Step three: Connect to Ethernet Port A .............. 7 Initial configuration ......................... -
Page 3: General Information
MSE 8000 chassis, combining continuous presence high definition video conferencing and the highest possible voice quality. Port and LED locations Figure 1 shows the position of ports and LEDs on the Cisco TS MSE 8710. MSE 8710 Figure 1: Cisco TS... -
Page 4: Led Behavior
LED behavior LED behavior Front panel LED behavior Table 1 describes the behavior of the LEDs on the front of the Cisco TS MSE 8710. TS MSE 8710 Table 1: Cisco front panel LED behavior Color Indicates USB Port Activity... -
Page 5: Installing The Cisco Ts Mse 8710
Getting Started Guide on http://www.tandberg.com/support/video- conferencing-documentation.jsp). Step one: Install the Cisco TS MSE 8710 blade into the MSE 8000 You must install either a blade or a blanking blade in each of the ten positions in the chassis. Remove the blade or blanking blade from the slot into which you are going to install the Cisco TS MSE 8710: Using a No. - Page 6 Open both retaining latches on the front of the Cisco TS MSE 8710. When open, a retaining latch is at a 90° angle perpendicular to the front of the blade. Slide the Cisco TS MSE 8710 into the blade slot (as shown in Figure 2) until it stops.
-
Page 7: Step Two: Allocate Port Licences
Figure 3: Closing the retaining latches on the front of a blade Step two: Allocate port licences Port licenses must be allocated to the Cisco TS MSE 8710 from the Supervisor's Port page. Refer to the online help for assistance. -
Page 8: Initial Configuration
The default setting for the Cisco TS MSE 8710 Ethernet ports is auto-sensing mode. If the switch ports to which you connect the Cisco TS MSE 8710 are not also set to auto-sensing mode, then you need to configure the Cisco TS MSE 8710 Ethernet ports to use the same speed and duplex mode. -
Page 9: Configuring The Cisco Ts Mse 8710
Step two: Configuring settings, conferences, endpoints and rooms Use the online help to configure your Cisco TS MSE 8710. You may need to configure the network and the systems settings, then go on to add conferences, endpoints and rooms. The online help also tells you how to provide instructions for... -
Page 10: Checking For Updates
Checking for updates Checking for updates It is a good idea to regularly check for updates to the main Cisco Telepresence Server software image on the Cisco web site. This section describes how to upgrade the Cisco Telepresence Server using the web. Note that you can also upgrade the Cisco Telepresence Server using FTP;... -
Page 11: Troubleshooting And Technical Support Information
If you experience any problems when configuring or using the Cisco TS MSE 8710 , consult the online help (available within the UI of your Cisco TS MSE 8710) for an explanation of how its individual features and settings work. If you cannot find the answer you need, check on the web site at http://www.tandberg.com/support... -
Page 12: Disclaimers And Notices
THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. www.cisco.com/go/ and other countries. A listing of Cisco's trademarks can be found at trademarks .