Auto-Learning Procedure For New Radio Controls; Active Arming - Cobra Bridge compact alarm Fitting Instruction And User Manual

R

AUTO-LEARNING PROCEDURE FOR NEW RADIO CONTROLS

AUTO-LEARNING PROCEDURE FOR NEW RADIO CONTROLS AUTO-LEARNING PROCEDURE FOR NEW RADIO CONTROLS AUTO-LEARNING PROCEDURE FOR NEW RADIO CONTROLS AUTO-LEARNING PROCEDURE FOR NEW RADIO CONTROLS
If a radio control is lost or begins to operate badly, is possible to replace it in safe way.
In fact this procedure is only permitted by the using of your PIN code. Proceed in the
following way:
1. 1. 1. 1. 1. Disarm the system.
2. 2. 2. 2. 2. Prepare all radio controls to add/replace.
3. 3. 3. 3. 3. Turn the ignition key ON, press both buttons on the radio control (art. 7777 or
7727) until the transmitter LED will go off.
4. 4. 4. 4. 4. Release the buttons and make sure that the LED on the radio control comes on in a
fixed way. Repeat step 3 and 4 for all the remotes to add. Switch the ignition OFF.
5. 5. 5. 5. 5. Turn the ignition key ON and then OFF for three times within 7 seconds.
6. 6. 6. 6. 6. The LED will blink once during 3 seconds signalling that you can insert the PIN code.
7. 7. 7. 7. 7. After the LED will go off turn the ignition ON and count the led blinks up to the
number which is the first digit of your PIN (referring to the example: 2 blinks=2 is
the first digit) then switch the ignition OFF.
Repeat the same procedure for all the digits.
In case of any mistake just wait for ten seconds with the ignition key OFF without
making any operation and then come back to step 5.
8. 8. 8. 8. 8. If the system has not already working electronic keys turn the ignition ON. The LED
will come on a fixed way signalling that the PIN is correct. Go to step 10.
9. 9. 9. 9. 9. If the system has already working electronic keys turn the ignition ON and then put
the key in connection with the emergency panel. The LED will come on a fixed way
signalling that the PIN is correct and that the electronic key has been identified.
10. 10. 10. 10. 10.Press one of the two buttons to make sure that the radio control LED blinks and that
the LED on the dash-board goes out for about 1 second.
11. 11. 11. 11. 11.Repeat the operation described in step 10 for all the remote controls you want to
add.
10.The auto-learning procedure can be interrupted at any moment by simply turning 10. 10. 10. 10.
the ignition key OFF.
Note: Note: Note: As soon as a new r As soon as a new remote contr As soon as a new r As soon as a new r emote contr emote contr emote control is added to the system it will automatically
Note: Note: As soon as a new r emote contr
put out of or put out of or put out of or put out of order the old TX set put out of or der the old TX set. . . . . If you want to keep them working you der the old TX set der the old TX set der the old TX set
must add the old TX again. The system works with 4 keys maximum. must add the old TX again. The system works with 4 keys maximum. must add the old TX again. The system works with 4 keys maximum.
must add the old TX again. The system works with 4 keys maximum. must add the old TX again. The system works with 4 keys maximum.
ACTIVE ARMING (If activated) ACTIVE ARMING (If activated) ACTIVE ARMING (If activated)
ACTIVE ARMING (If activated) ACTIVE ARMING (If activated)
When activated this function will cause the automatic arming of the system. This
happens after two minutes the system has been disarmed and any door has not been
opened. The system will not operate the CDL.
16
GB
ol is added to the system it will automatically ol is added to the system it will automatically ol is added to the system it will automatically
ol is added to the system it will automatically
If you want to keep them working you If you want to keep them working you If you want to keep them working you If you want to keep them working you
PIN CODE
PIN CODE = 2341
EXAMPLE
OFF
ON ON
+
a
IGN IGN
MAX 7 SEC.
ON LED ON X 2
b
3 4 1
ON
LED ON X 3
c
2 4 1
LED ON X 4
ON
d
2 3 1
ON LED ON X 1
e
2 3 4
ON OK
ON 3 SEC.
OFF OFF
ON
+ =
OK
IGN
OFF
OFF
OFF
OFF
GB
R
17