Electrical Connections; Voltage Drop Sensor; Positioning The Approval Labels - Cobra Bridge compact alarm Fitting Instruction And User Manual

Hide thumbs

Table Of Contents

Table of Contents

Enlarged version

VOLUMETRIC ULTRASONIC SENSOR (Ref. B)

The transducers can be installed on the windscreen or rear window pillars. The best

place is just above the surface of the dashboard.

Wherever they are installed, make sure that the transducers do not interfere with any

other parts.

It is of fundamental importance to correctly position the transducers so that they are

able to offer a full degree of volumetric protection: direct the transducers towards the

rear window so that they approximately converge towards the center of it. Fix them

with the supplied screws. Make sure that the transducers are not obstructed by any

other object (plugs, covers, upholstery).

This unit incorporates an ultrasonic sensor that does not need to be adjusted. It

is alr

is already pr

is alr

eady pr

eady presetted indipendently by the dif

eady pr

esetted indipendently by the dif

esetted indipendently by the differ

is alr

eady pr

esetted indipendently by the dif

GLASS BREAK SENSOR (ref. A)

Remember to fix the relative microphone in a central position of the vehicle. The best

place is on the dashboard, pointing towards the rear window. This position achieves

uniform sensitivity.

BONNET BUTTON

Use the material supplied in the kit. After it has been installed, make sure that the

button is pressed by the bonnet to the extent of at least 5 mm. Make sure that the

button is unable to press against the soundproofing panels or on the external bodywork

since these materials could become deformed in time.

Cover the button with a film of grease to protect it from rust.

ANTENNA

The antenna is of fundamental importance for operation of the radio control system.

Comply with the following instructions:

The wire must not be cut, wound, connected to other wires or to the bodywork.

Keep the antenna at least 20 mm far from the car body and other metallic parts.

ferent vehicle inter

fer

ent vehicle internal space.

ent vehicle inter

nal space.

fer

ent vehicle inter

nal space.

ELECTRICAL CONNECTIONS

We raccomand you to pay attention while joining together two or more wires. It is

inadvisable to make "quick junctions" that fail to ensure good quality connections.

Remember to position the alarm wires so that they are routed along with the original

harness of the vehicle and to attach them to this with the relative clamps.

Refer to the enclosed wiring diagrams when making the electrical connections, bearing

the following instructions in mind.

• the ground must be shunted from an original ground point of the vehicle or connected

straight to the negative pole of the battery.

• the positive wires of the alarm unit must be connected to a positive of the fuse box

(with the voltage drop sensor activated the alarm unit power supply must be connected

to the entry light wire feed).

• the engine immobiliser function must be obtained by interrupting the fuel pump relay

or pump control circuits. It is essential to block the fuel pump in vehicles with catalytic

silencers. The internal relay and the engine immobiliser wires withstand the maximum

current rating indicated in the wiring diagrams. Before connecting the GREEN wires,

remember to measure the current in the point selected for the connection.

The interrupted wire can be either positive or negative

• The unit is alr

The unit is alr

The unit is already equipped with inter

The unit is alr

eady equipped with internal solid state electr

eady equipped with inter

not necessary to add fuses in the wiring harness and to open the alar

not necessary to add fuses in the wiring har

for the inter

for the internal fuses r

for the inter

nal fuses replacement. In case of short cir

nal fuses r

eplacement. In case of short cir

eplacement. In case of short circuit wich could r

eplacement. In case of short cir

the system per

the system perfor

for

formances it will be enough to r

for

mances it will be enough to r

mances it will be enough to remove the short cir

the system to the standar

d operation.

the system to the standard operation.

the system to the standar

d operation.

VOLTAGE DROP SENSOR (if activated)

The voltage drop sensor is also built-in and it is able to detect at least a 5W interior

lamp which is switched on. When this sensor is activated the power supply red wire

must be connected after the interior lamps fuse.

POSITIONING THE APPROVAL LABELS

The radio controls are supplied with homologation numbers for Germany and UK

already printed.

The other approvals are include on the labels supplied in the kit. Just choose the label

bearing the initial of your country and apply it as indicated in the figure

NOTE: The remaining labels must not be used.

nal solid state electr

nal solid state electronic fuses. It is

nal solid state electr

onic fuses. It is

ness and to open the alar

ness and to open the alarm unit

ness and to open the alar

m unit

cuit wich could reduce

cuit wich could r

educe

emove the short cir

emove the short circuit r

emove the short cir

cuit r

cuit restoring

estoring

Table of Contents

Show Quick Links

Hide quick links:

Table of Contents

Electrical Connections; Voltage Drop Sensor; Positioning The Approval Labels - Cobra Bridge compact alarm Fitting Instruction And User Manual

ELECTRICAL CONNECTIONS

POSITIONING THE APPROVAL LABELS

Hide quick links:

Related Manuals for Cobra Bridge compact alarm

Related Content for Cobra Bridge compact alarm

Table of Contents