Download  Print this page

Stall Prevention Operation - Mitsubishi Electric FR-A720-0.4K Instruction Manual

Fr-a700 series.
Hide thumbs
   
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472

Advertisement

Adjust the output torque of the motor (current)
4.8.4
Stall prevention operation (Pr. 22, Pr. 23, Pr. 48, Pr. 49, Pr. 66, Pr. 114, Pr. 115,
Pr. 148, Pr. 149, Pr. 154, Pr. 156, Pr. 157, Pr. 858, Pr. 868)
This function monitors the output current and automatically changes the output frequency to prevent the inverter
from coming to an alarm stop due to overcurrent, overvoltage, etc. It can also limit stall prevention and fast
response current limit operation during acceleration/deceleration, driving or regeneration. Invalid under real
sensorless vector control or vector control.
Stall prevention
If the output current exceeds the stall prevention operation level, the output frequency of the inverter is
automatically varied to reduce the output current.
Also the second stall prevention function can restrict the output frequency range in which the stall prevention
function is valid. (Pr. 49)
Fast response current limit
If the current exceeds the limit value, the output of the inverter is shut off to prevent an overcurrent.
Parameter
Name
Number

Stall prevention operation

22
level
Stall prevention operation
23
level compensation factor
at double speed
Second stall prevention
48
operation current
Second stall prevention
49
operation frequency
Stall prevention operation
66
reduction starting frequency
Third stall prevention
114
operation current
Thrid stall prevention
115
operation frequency
Stall prevention level at 0V
148
input
Stall prevention level at
149
10V input
Voltage reduction
154
selection during stall
prevention operation
Stall prevention operation
156
selection
157
OL signal output timer
Terminal 4 function
858
assignment
Terminal 1 function
868
assignment
Pr. 22
Constant
speed
OL
Stall prevention operation example
CAUTION
⋅ If an overload status lasts long, an inverter trip (e.g. electronic thermal relay function (E.THM)) may occur.
⋅ When Pr. 156 has been set to activate the fast response current limit (initial setting), the Pr. 22 setting should not be higher than
170%. The torque will not be developed by doing so.
⋅ When real sensorless vector control or vector control is selected using Pr. 800 Control method selection, Pr.22 serves as torque limit level.
For the 3.7K or less, the Pr. 22 setting changes from 150% (initial value) to 200%.
148
Initial Value
150%
9999
150%
0Hz
60Hz
150%
0Hz
150%
200%
1
0
0s
0
0
(1) Setting of stall prevention operation level (Pr. 22)
Output current
⋅ Set in Pr. 22 the ratio of the output current to the rated inverter current at
which stall prevention operation will be performed. Normally set 150%
(initial value).
Output frequency
⋅ Stall prevention operation stops acceleration (makes deceleration) during
acceleration, makes deceleration during constant speed, and stops
deceleration during deceleration.
Time
⋅ When stall prevention operation is performed, the OL signal is output.
Setting
Range
0
Stall prevention operation selection becomes invalid.
Set the current value at which stall prevention
0.1 to 400%
operation will be started.
The stall operation level can be reduced when
0 to 200%
operating at a high speed above the rated frequency.
9999
Constant according to Pr. 22
0
Second stall prevention operation invalid
0.1 to 220%
The second stall prevention operation level can be set.
0
Second stall prevention operation invalid
Set the frequency at which stall prevention operation
0.01 to 400Hz
of Pr. 48 is started.
9999
Pr. 48 is valid when the RT signal is on.
Set the frequency at which the stall operation level is
0 to 400Hz
started to reduce.
0
Third stall prevention operation invalid
Stall prevention operation level can be changed with
0.1 to 220%
the X9 signal.
0
Third stall prevention operation invalid
Set the frequency at which stall prevention operation
0.01 to 400Hz
when the X9 signal is on starts.
0 to 220%
Stall prevention operation level can be changed by
the analog signal input to terminal 1 (terminal 4).
0 to 220%
0
With voltage reduction
1
Without voltage reduction
0 to 31,
You can select whether stall prevention operation and fast
100, 101
response current limit operation will be performed or not.
Set the output start time of the OL signal output when
0 to 25s
stall prevention is activated.
9999
Without the OL signal output
By setting "4", the stall prevention operation level can
0, 1, 4, 9999
be changed with a signal to terminal 4.
By setting "4", the stall prevention operation level can
0 to 6, 9999
be changed with a signal to terminal 1.
V/F
V/F
V/F
Magnetic flux
Magnetic flux
Magnetic flux
Description
You can select whether to use
output voltage reduction during
stall prevention operation or not.

Advertisement

Table of Contents

   Related Manuals for Mitsubishi Electric FR-A720-0.4K

   Related Content for Mitsubishi Electric FR-A720-0.4K

Comments to this Manuals

Symbols: 0
Latest comments: