Download  Print this page

Output Current Detection Function (y12 Signal, Y13 Signal, Pr. 150 To Pr. 153, Pr. 166, Pr. 167) - Mitsubishi Electric FR-A720-0.4K Instruction Manual

Fr-a700 series.
Hide thumbs
   
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472

Advertisement

4.15.8 Output current detection function
(Y12 signal, Y13 signal, Pr. 150 to Pr. 153, Pr. 166, Pr. 167)
The output power during inverter running can be detected and output to the output terminal.
Parameter
Name
Number
Output current detection
150
level
Output current detection
151
signal delay time
152
Zero current detection level
153
Zero current detection time
Output current detection
166
signal retention time
Output current detection
167
operation selection
9999, Pr. 167 = 0
Pr. 166
Pr. 150
Output current
Pr. 151
Output current
OFF
detection signal
(Y12)
Initial Value
150%
0s
5%
0.5s
0.1s
0
(1) Output current detection (Y12 signal, Pr. 150, Pr.
151, Pr. 166, Pr. 167 )
⋅ The output current detection function can be used for excessive
torque detection, etc.
⋅ If the output current remains higher than the Pr. 150 setting during
inverter operation for longer than the time set in Pr. 151, the
output current detection signal (Y12) is output from the inverter's
Time
Pr. 166
open collector or relay output terminal.
Minimum 100ms
⋅ When the Y12 signal turns on, the ON state is held for the time
(initial value)
set in Pr. 166 .
OFF
ON
⋅ When Pr. 166 = "9999", the ON state is held until a next start.
⋅ At the Pr. 167 setting of "1", the inverter output is stopped and the
output current detection alarm (E.CDO) is displayed when the
Y12 signal turns on. When an alarm stop occurs, the Y12 signal
is on for the time set in Pr. 166 at the Pr. 166 setting of other than
9999, and remains on until a reset is made at the Pr. 166 setting
of 9999. E.CDO does not occur even if "1" is set in Pr. 167 while
Y12 is ON. The Pr. 167 setting is made valid after Y12 turns OFF.
⋅ Set "12 (positive logic)" or "112 (negative logic)" to any of Pr. 190
to Pr. 196 (output terminal function selection) to assign the function
of the Y12 signal to the output terminal.
Function assignment of external terminal and control
Setting Range
Set the output current detection level. 100%
0 to 220%
is the rated inverter current.
Set the output current detection period. Set
the time from when the output current has
0 to 10s
risen above the setting until the output current
detection signal (Y12) is output.
Set the zero current detection level. The rated
0 to 220%
inverter current is assumed to be 100%.
Set this parameter to define the period from
when the output current drops below the Pr.
0 to 1s
152 value until the zero current detection
signal (Y13) is output.
Set the retention time when the Y12 signal is
0 to 10s
on.
The Y12 signal on status is retained. The
9999
signal is turned off at the next start.
Operation continues when the Y12 signal is
0
on
The inverter is brought to an alarm stop when
1
the Y12 signal is on. (E.CDO)
Description
239
4

Advertisement

Table of Contents

   Related Manuals for Mitsubishi Electric FR-A720-0.4K

   Related Content for Mitsubishi Electric FR-A720-0.4K

Comments to this Manuals

Symbols: 0
Latest comments: