Panasonic UF-585 Service Manual page 151

1. Printer Error Code Table
Error
Code
00 No problem detected
10 The Timing Sensor turned OFF before a certain period of
time.
11 Timing Sensor did not turn ON within a certain period of time.
(Original Cassette Feeder)
12 Timing Sensor did not turn ON within a certain period of time.
(250 sheet Optional Cassette Feeder)
14 Timing Sensor did not turn OFF within a certain period of time. 1. Recording Paper Jam.
15 Paper Eject Sensor did not turn ON within a certain period of
time.
16 Paper Eject Sensor did not turn OFF within a certain period of
time.
17 Timing Sensor detected paper while initializing the unit.
18 Paper Exit Sensor detected paper while initializing the unit.
22 The temperature of the Fuser Roller remained low even after
the circuit was activated.
23 Abnormally high Fuser Roller temperature after the circuit was
de-activated.
24 The temperature of the Fuser Roller was not controlled within
a certain margin.
25 Thermistor open.
26 Thermistor detected temperature over 200°C.
31 The Tetragon Motor did not reach a constant speed of 7018
rpm (400dpi)/10762 rpm (600dpi) within a certain period of
time.
32 The Tetragon Motor did not maintain a constant speed of 7018
rpm (400dpi)/10762 rpm (600dpi).
36 HSYNC signal abnormal.
54 A/D Converter error.
61 Unit detected "No Toner Cartridge".
63 Unit detected "Printer Door Open".
64 Unit detected "No Cassette".
65 Unit detected "Out of Paper".
81 No response from LP controller.
82 Illegal response from LP controller
Note:
If an 021 series Error Code occurs, 021-25 (Thermistor Open) or 021-26 (Thermistor detected temperarure over 200 °C), a
pre-programmed recovery safety software is activated to protect the unit and the service personnel during abnormal increase in
temperature.
Once activated, this program is downloaded into the LPC PC Board's SRAM, disabling the Fuser Lamp and preventing it from
turning ON again.
In order to reset this circuit, please follow the procedure below.
1) Reset the LBP Fuser by using Service Mode 7-1-2 (Section 5.7) and Power OFF/ON.
2) Replace the Thermistor or Fuser Unit. If the problem persists.
3) Replace the LPC PCB.
Description of Problems Cause
1. Recording Paper Jam.
2. Timing Sensor defective
3. Incorrect paper size setting.
1. Recording Paper misfeeding, Paper Feed Roller defective.
2. Drive Clutch defective.
3. Timing Sensor defective.
1. Recording Paper misfeeding, Paper Feed Roller defective.
2. Drive Clutch defective.
3. Timing Sensor defective.
2. Timing Sensor defective
3. Incorrect paper size setting.
1. Recording Paper Jam.
2. Paper Exit Sensor defective.
1. Recording Paper Jam.
2. Paper Exit Sensor defective.
1. Recording Paper jammed in the unit.
2. Timing Sensor defective.
1. Recording Paper jammed in the unit.
2. Paper Exit Sensor defective.
1. Fuser Unit defective.
2. LPC PCB defective.
3. LVPS defective.
1. Fuser Unit defective.
2. LPC PCB defective.
3. LVPS defective.
1. Fuser Unit defective.
2. LPC PCB defective.
3. LVPS defective.
1. Thermistor defective (Fuser Unit).
2. LPC PCB defective.
1. Thermistor defective (Fuser Unit).
2. LPC PCB defective.
3. LVPS defective.
1. LSU defective.
1. LSU defective.
1. LSU defective.
2. LPC PCB defective.
1. LPC PCB defective.
1. Toner Cartridge not installed.
2. Toner Sensor defective.
1. Printer door is not closed.
2. ILS PCB defective.
1. Cassette not installed or partially open.
2. Cassette Sensor defective.
1. Cassette(s) ran out of receiving paper.
2. Paper Detect Sensor defective.
1. LPC PCB defective
1. LPC PCB defective
Service Modes
157