Panasonic UF-585 Service Manual page 144

Panasonic UF-585 / 595
No. Parameter (see Note 3)
041 PAUSE TIME
042 Not used
043 REDIAL INTERVAL
044 REDIAL COUNT
045 RING DETECT COUNT
046 ON-HOOK TIME
047 RESPONSE WAIT
048 Not used
049
050 RING DETECT MODE
051 Not used
052 PULSE RATE
053 Not used
054
055 BUSY TONE CHECK
056 DIAL TONE CHECK
(Except for USA and Canada
version)
057 DC LOOP CHECK
(Except for USA and Canada
version)
058 COMM.JRNL +IMAGE
059 CONFIDENTIAL RCV
REPORT
060 VERSION
061 TX/RX//PRT/CPY COUNTER
062 PRINT COUNTER
063 Not used
064 SILENT DETECTION TIME
OUT
065 SILENT INTEGRATION TIME 01 = 1 sec.
066 RING COUNT (TAM)
067 SELF-LEARNING
068 NYSE FAX FORWARD
(For USA and Canada only)
069 NYSE LOCAL PRINT
(For USA and Canada only)
150
Function Parameter Table
Selections
1 = 1 sec.
~
10 = 10 sec.
0 = no waiting
~
15 = 15 minutes
0 = no redial
~
15 = 15 times
1 = 1 ring
~
9 = 9 rings
0 = 0 sec.
~
90 = 90 sec.
1 = 1 sec.
~
90 = 90 sec.
1 = Normal
2 = Rough
1 = 10 pps
2 = 20 pps
1 = Off
2 = On
1 = Off
2 = On
1 = Off (will not check)
2 = On (checks)
1: Off (without image)
2: On (with image)
1 = Off (does not print out)
2 = On (prints out)
Displays the ROM version.
TX/RX/PRT/CPY
1 = Off
2 = On
01 = 1 sec.
~
60 = 60 sec.
~
10 = 10 sec.
1 = 1 ring
~
99 = 99 ring
1 = A4
2 = LETTER
1 = Off
2 = On
1 = Incomplete
2 = On (Always)
Function
Selects the pause interval from 1 sec. ~ 10 sec. for
dialing through a switchboard or for international
calls.
Selects the redial interval from 0 to 15 minutes in 1
minute steps.
Selects the redial count from 0 to 15 times in 1 step
intervals.
Selects the ring detection count from 1 to 9 rings in
1 ring step intervals.
Selects the on-hook time between sequential
communication calls in 1 second step intervals.
Selects the waiting interval for the response after
completing the dialing.
Selects the quality of ringer detection. Use if the
line signal is out of regulation, set to "Rough" so
that the unit may detect the ringing signals.
Selects the dial pulse rate 10/20 pps.
Selects whether to detect the Busy Tone.
Selects whether to detect dial tone before dialing
the telephone number.
Selects whether the unit checks the DC Loop
during communication.
Selects whether the machine prints the COMM.
Journal with image.
Selects whether the machine prints the
CONFIDENTIAL RCV REPORT.
Displays the transmitted, received, total printed and
copied document count.
Selects whether to print in the Fax Parameter List,
the counter information that is displayed in the
Function Parameter No. 61.
Selects silent detection timeout time (TAM I/F).
Selects ring detection integration time (TAM I/F).
Selects ring detection count 1 to 99 times in one
step intervals on TAM I/F mode.
Selects the default paper size to be used when the Legal
Size recording paper is replaced with either Letter/A4
size paper without setting the corresponding Recording
Paper Size in the Fax Parameter No. 23.
Selects whether the machine will forward the
incoming and outgoing faxes to a specified ABBR
or One-Touch station.
Selects the printing condition for the incoming faxes
after FAX Forwarding.
INC. : Prints only if FAX Forwarding fails.
ON : Always prints.