Information Code Table - Panasonic UF-585 Service Manual

Panasonic UF-585 / 595
4.7

Information Code Table

Code Mode
001 RCV
COPY
002 RCV
COPY
007 RCV
COPY
008 RCV
COPY
010 RCV
COPY
011 STANDBY
012 RCV
021 STANDBY
RX
COPY
026 -
030 XMT
031 XMT
COPY
033 -
041 STANDBY
RX
COPY
043 STANDBY
RX
COPY
045 STANDBY
051 RCV
COPY
054 STANDBY
RX
COPY
055 STANDBY
RX
COPY
059 RCV
COPY
060 -
061 -
200 RCV
212 XMT
RCV
301 XMT
RCV
331 XMT
400 XMT
401 XMT
136
Information Codes
Phase Description of Problem
C,D Leading edge of the recording paper fails to
reach the Timing Sensor. (1st cassette)
C,D Leading edge of the recording paper fails to
reach the Timing Sensor. (2nd cassette)
C,D 1.Leading edge of the recording paper fails to
reach the Paper Exit Sensor.
2.Recording paper has not completely passed
the Paper Exit Sensor.
C,D Paper Cassette was opened while the recording
paper was feeding.
B,C No recording paper.
B,C Paper Cassette is not installed properly.
C,D The length of the received document is over 2m.
B,C,D Thermister is abnormal.
Fuser Control is abnormal.
- The backup battery is getting weak.
B Read Point Sensor does not go ON within 10
seconds after the document starts feeding.
C Transmitting document was longer than
2,000mm (or 78.7 in).
- Sub CPU system error.
B,C,D Out of toner.
B,C,D Low toner.
- No Toner Cartridge.
- Printer Motor abnormal.
- HSYNC abnormal.
Laser motor abnormal.
- No response of LBP CPU on LPC.
C Interface error occurred between SCA/SCB
PCB and LPC PCB.
A Printer Cover is open.
A ADF Door is open.
C Decoding process is not completed at the end of
phase C.
A-E Interface error occurred between the CPU and
modem.
System fault.
C 8-minutes timer error. (Germany only)
B T1 timer (35±5 sec) elapsed without detecting
300 bps signal.
B DCN was returned from receiver while
transmitter is waiting for CFR or FTT.
Cause
Recording paper jam.
Timing Sensor abnormal.
Recording paper jam.
Timing Sensor abnormal.
Recording paper jam.
Paper Exit Sensor abnormal.
Recording paper jam.
No recording paper or paper is not set
properly.
No Paper Sensor is defective.
Defective LPC PCB.
Defective Fuser Unit, LVPS.
Document is not set properly.
Defective Read Point Sensor.
The document may jam.
Defective Read Point Sensor.
Defective SCA/SCB PCB.
No toner.
Defective Toner Sensor.
Toner is getting low.
Defective Toner Sensor.
Toner cartridge has not been installed.
Defective Toner Sensor (Cartridge Sensor).
Connector not properly connected.
Defective Printer Motor.
Defective LPC PCB.
Defective Laser Unit.
Defective LPC PCB.
Defective SCA/SCB PCB.
Defective LPC PCB.
Defective SCA/SCB PCB.
Cover is not firmly closed.
Connectors are not firmly connected.
Cover is not firmly closed.
Connectors are not firmly connected.
Defective SCA/SCB PCB.
Modem is defective. (SCA/SCB PCB)
Software problem occurred. (SCA/SCB PCB)
Software problem occurred. (SCA/SCB PCB)
Wrong number is dialed and the START button
is pushed.
Telephone line is disconnected while dialing.
SCA/SCB PCB (Modem) or LCU PCB is
defective.
Receiver is defective. (It may only be
transmitting CED)
Your machine's ID Number is not programmed.
Possible incompatibility or incorrect Password
(Password Reception, Selective Receive).
Mailbox is full.