Table of Contents
Advertisement
SW24 No. 8 Fax printing when low ink detected
To print the received picture in "Low Ink" state, set "1'.
SW25 No. 1 - No. 5 Align cartridge (l-30) for black cartridge
After the black cartridge has been mounted press
"FUNCTION", "8, %", "H", x',
"START"
to print Bidirectional Alignment Pattern.
On the printed test page, locate the number under the Bidirectional Align-
ment pattern that comes closest to forming a perfectly straight line.
SW25 No. 8 Cartridge alarm
Set
existence/nonexistence of alarm tone alarming the failure of return
of cartridge to the home position.
SW25 No. 7 Low ink detection in black cartridge
Set
detectionlnondetection of black ink "Low ink".
SW25 No. 8 Low ink detection in color cartridge
Set
detectionlnondetection of color ink "Low ink".
SW28 No. 1 Automatic reduce of receive
If set to 1, it is reduced automatically when receiving.
SW28 No. 2 Cut off mode (COPY mode)
Whether the excessive part is printed on the next recording paper or
discarded is selected to copy a document which is longer than the re-
cording paper.
SW28 No. 3 Reserved
set to "0".
SW28 No. 4 - No. 8 IrDA selection
Set the
other party of Ir communication.
SW28 No. 7, No. 8 Reserved
Set to "0".
SW27 No. 1, No. 2 DTMF detection time
Used to set detect time of DTMF (Dual Tone Multi Frequency) used in
remote reception (5 H H).
The longer the detect time is, the less the error detection is caused by
noises.
SW27 No. 3 Protection of remote reception (5 x x) detect
Used to set the function of remote reception (5 K x). When set to "l",
the remote reception functon is disabled.
SW27 No. 4 Remote reception with GE telephone
(Corresponding to TEL made by GE) P.B.X.
"1": Compatible with TEL mode by GE
"0": Not compatible
l
When sending (5 x xc) for remote reception with a GE manufactured
telephone remote reception may not take place because of special
specifications in their DTMF.
To overcome this, a soft SW is provided to change the modem set-
ting to allow for remote reception.
l
If this soft SW is set to "l", other telephone sets may be adversely
affected.
SW27 No. 5 - No. 8 Remote operation code figures by external tel
(8-Q)
Remote operation codes can be changes from 0 through 9. If set to
greater than 9, it defaults to 9. The "5 x ++" is not changed.
Ex-7~ x (Default
:
5 H x).
SW28 No. 1 Busy tone detection ON/OFF time (Shorter duration)
The initial value of detection is set according to electric condition.
The set value is changed according to the local switch board. (Errone-
ous detection of sound is reduced.)
Normally the upper limit is set to 2700msec. and the lower limit to
15Omsec.
If erroneous detection is caused by sound, etc., adjust the detection
range.
The lower limit can be set in the range of 350msec to 150msec.
SW28 No. 2, No. 3 Busy tone detection ON/OFF time
(Longer duration)
Similarly to SW-28 No.1, the set value can be varied.
The upper limit can be set in the range of 65Omsec to 2700msec.
SW28 No. 4 Busy tone continuous sound detect tima
Set detecting time busy tone for 5 seconds or as is PlT.
SW28 No. 5 Busy tone detect continuation sound detect
Used to select detection of the continuous sound of certain frequency.
SW28 No. 8 Busy tone detect intermittent sound detect
Used to select detection of the intermittent sound of certain frequency.
SW28 No. 7, No. 8 Busy tone detection pulse number
Used to set detection of Busy tone intermittent sounds.
SW29 No. 1 TAD connect
When connecting the answering machine to the extension telephone
jack.
Set to "1 I'.
SW29 No. 2 Fax switching when A.M.full
If the answering machine's memory (tape) is full and there is no re-
sponse, the machine automatically switches to Fax reception.
SW29 No. 3, No. 4 Section tims of quiet detection
The switch which sets the time from the start of detection function to the
end of the function.
SW29 No. 5, No. 6 Number of CNG detect (AM mode)
Used for detection of CNG in 1 to 4 pulses.
SW29 No. 7, No. 8 Reserved
Set to "0".
SW38 No. 1 - No. 4
Quiet
detect time
When an answering machine is connected, if a no sound state is de-
tected for a certain period of time, the machine judges it as a transmis-
sion from a facsimile machine and automatically swiches to the Fax
mode.
SW30 No. 5 - No. 8 Quiet detect start timing
Inserts a pause before commencing quiet detection.
SW31 No. 1 - No. 8 Reserved
Set to "0".
SW32 No. 1 - No. 8 ReaeNed
Set to "0".
SW33 No. 1 - No. 8 Reserved
Set to "0".
SW34 No.
1
- No. 8 Reserved
Set to "0".
SW35 No. 1 - No. 3 Reserved
Set to "0".
SW35 No. 4 Reserved
Set to "1".
SW35 No. 5 - No. 8 Reserved
Set to "0".
2-16
Advertisement
Table of Contents
