Related Manuals for Polycom BelAir50
Summary of Contents for Polycom BelAir50
- Page 1 VIEW Certified Configuration Guide BelAir Networks BelAir50, BelAir100, BelAir200 January 2008 Edition 1725-36065-001 Version D...
-
Page 2: Trademark Information
Polycom personnel and customers. The LinkPlus drawings and specifications contained herein Link are the property of Polycom and shall be neither NetLink reproduced in whole or in part without the prior written approval of Polycom, nor be implied to... -
Page 3: Certified Product Summary
SpectraLink 8000 Wireless Telephones and WLAN infrastructure products. The products listed below have been thoroughly tested in Polycom’s lab using the VIEW Certification Test Plan. This document details how to configure BelAir access points (APs) with SpectraLink 8000 Wireless Telephones. -
Page 4: Known Limitations
Configuration Guide Known Limitations • IMPORTANT NOTE: VIEW Certification testing verifies that the user access radio of the BelAir AP 50/100/200 meets the VIEW technical requirements for supporting SpectraLink 8000 Wireless Telephones in a typical enterprise deployment. Testing is conducted in a laboratory where neither outdoor AP coverage area/range nor multiple mesh ‘backhaul hops’... -
Page 5: Network Topology
Network Topology The following topology was tested during VIEW Certification testing. SpectraLink 8000 SVP Server BelAir100 SpectraLink 8000 Wireless Telephones SpectraLink 8000 Telephony Gateway Ethernet switch BelAir100 For information on Polycom products depicted in this diagram, visit www.spectralink.com. PN: 1725-36065-001_D.doc... -
Page 6: Configuration Settings Using The Cli
Configuration Guide Configuration Settings Using the CLI The following table contains the configuration parameters recommended for interoperability with SpectraLink 8000 Wireless Telephones. Mode: SVP: Enable Voice SSID: Map to VLAN 100 QoS mapping: Map VLAN 100 to queue 3 Antenna Diversity: Enable BelAir access radios implement SVP. -
Page 7: Change Access Channel
BelAir Networks: BelAir50, BelAir100, BelAir200 Change access SSID The following commands display and change the access SSID. In the example, below, the first SSID is set to “Data” to be used for data traffic and the second SSID is set to “Voice” for voice traffic. The second voice SSID is assigned to VLAN 100. -
Page 8: Set Antenna Diversity
Configuration Guide Set WPA2-PSK for access The following commands enable/disable the WPA2-PSK for the voice SSID (ssidx 2). /# cd /radio /radio# set arm1 wpa2 psk <Pre-Shared Key> ssidx 2 enabled /radio# set arm1 wpa2 ssidx 2 disable Set antenna diversity The following commands enable antenna diversity. -
Page 9: Reboot The Node
BelAir Networks: BelAir50, BelAir100, BelAir200 Reboot the node The following commands reboot the AP. It is not necessary to reboot the node after changing the configuration. /# cd /system /# /system/reboot Other setup Please refer to BelAir User Guide for other supported commands. -
Page 10: Configuration Settings Using The Web Interface
Configuration Guide Configuration Settings Using the Web Interface The following table contains the configuration parameters recommended for interoperability with SpectraLink 8000 Wireless Telephones. Mode: SVP: Enable Voice SSID: Map to VLAN 100 QoS mapping: Map VLAN 100 to queue 3 Antenna Diversity: Enable BelAir access radios implement SVP. -
Page 11: Configure The Access Radio
BelAir Networks: BelAir50, BelAir100, BelAir200 Configure the access radio 1. Click the button. ACCESS 2. In the navigation pane, click General Config. 3. Make sure that the is set to Radio State Enable 4. Set the levels according to deployment plan. - Page 12 Configuration Guide BelAir’s internal access antennas have 8 dBi gain, which is the default setting for this field. If a different antenna is used, then this setting should be changed accordingly. Please refer to the BelAir Hardware Products: Deployment Guidelines manual for more information.
- Page 13 BelAir Networks: BelAir50, BelAir100, BelAir200 6. Enter your new voice name. SSID 7. Make sure that MBSSID Disabled 8. In this example configuration, we mapped the voice SSID to VLAN and enabled Intra-AP client to client communications 9. Select your , and enter a as indicated.
- Page 14 Configuration Guide MBSSID Disabled must be so that there is a single SSID carrying SpectraLink voice traffic. If MBSSID is enabled, each SSID gets its own BSSID, causing the SpectraLink 8000 SVP Server to not work properly, since the SVP Server would perceive the two SSIDs on an AP to be two different APs.
- Page 15 BelAir Networks: BelAir50, BelAir100, BelAir200 Set up QoS 1. Click the button. SYSTEM 2. In the navigation pane, click QoS Configuration 3. If the top-left button is labeled , then SVP is already Disable SVP enabled. Otherwise it will be labeled .