Digital Input; B List Of "Alarm And Warning Codes - Lauda E 4 G Operating Instructions Manual

B List of "Alarm and warning codes"
Alarms
Alarm code
Low Level Pump
1
2 Low Level Pump
3 Overtemperature
4 Pump blocked
5 Connection Command
9 T ext Pt100
T ext analog
10
11 T ext serial
12 Input Analog 1
13 Input Analog 2
15

Digital Input

Warnings
Code 0XX Control sys-
tem
1 CAN receive overf
2 Watchdog Reset
3 T_il limit active
4 T_ih limit active
5 corrupt parameter
6 corrupt progr
7 Invalid Parameter
8 CAN system
9 Unknown Modul
10 SW control too old
11 SW safety too old
12 SW command too
old
13 SW cool too old
14 SW analog too old
15 SW serial too old
16 SW contact old
17 SW Valve 0 old
18 SW Valve 1 old
19 SW Valve 2 old
20 SW Valve 3 old
21 SW Valve 4 old
26 SW HTC old
27 SW Ext Pt100 old
33 RTC wrong data
41 wrong net voltage
42 no eco type
43 no eco voltage
44 chiller missing
45 Diff.voltages
86
Meaning
Pump runs too fast (low level)
Low level in the float
Overtemperature (T > Tmax)
Pump blocked (standstill)
Remote control unit command triggered in running operation
External Pt100 actual value is not present.
External analog actual value is not present.
External serial actual value is not present.
Analog module: Current interface 1, interruption.
Analog module: Current interface 2, interruption.
Error on digital input
Meaning
Overflow during CAN reception
Watchdog reset
til llmit active
tih llmit active
Inadmissible internal parameter
Inadmissible programmer data
Inadmissible parameter in memory
Problem during internal data interchange
Unknown module connected
Software version of control panel too old
Software version of protection too old
Software version of command remote
control unit too old
Software version of cooling module too old
Software version of analog too old
Software version of serial too old
Software version of contact module too old
Software version of solenoid valve too old
Software version of solenoid valve 1 too old
Software version of solenoid valve 2 too old
Software version of solenoid valve 3 too old
Software version of solenoid valve 4 too old
Software version of high temperature cooler
too old
Software version of external Pt100 too old
Internal clock defective
Incorrect mains voltage setting
Device type not configured
Mains voltage not configured
Chiller not running
Different mains voltage configured (head
and cooling underpart)
Appendix with settings
Code 3XX SmartCool
1 CAN receive overf
2 Watchdog Reset
3 adaption missing
4 Pressure switch
activated
5 Clean condenser
6 TO1 out of range
(Klixon)
7 Invalid Parameter
8 CAN system
9 Unknown Modul
10 SW control too old
11 SW safety too old
12 SW command too
old
13 SW cool too old
14 SW analog too old
15 SW serial too old
16 SW contact old
17 SW Valve 0 old
18 SW Valve 1 old
19 SW Valve 2 old
20 SW Valve 3 old
21 SW Valve 4 old
26 SW HTC old
27 SW Ext Pt100 old
33 valve sm0 break
34 valve sm1 break
35 valve sm2 break
36 valve sm3 break
37 output sm0
38 output sm1
39 output sm2
40 output sm3
41 sm0 min too small
42 no eco type
43 no eco voltage
44 chiller missing
ECO GOLD
Meaning
Overflow during CAN reception
Watchdog reset
No adaption run
Pressure Switch in cooling circuit triggered
Clean condenser
Injection temperature outside value range
Inadmissible parameter in memory
Problem during internal data interchange
Unknown module connected
Software version of control panel too old
Software version of protection too old
Software version of command remote
control unit too old
Software version of cooling module too old
Software version of analog too old
Software version of RS232 too old
Software version of contact module too old
Software version of solenoid valve 0 too old
Software version of solenoid valve 1 too old
Software version of solenoid valve 2 too old
Software version of solenoid valve 3 too old
Software version of solenoid valve 4 too old
Software version of high temperature cooler
too old
Software version of external Pt100 too old
Cable of injection valve 0 defective
Cable of injection valve 1 defective
Cable of injection valve 2 defective
Cable of injection valve 3 defective
Triggering of injection valve 0 defective
Triggering of injection valve 1 defective
Triggering of injection valve 2 defective
Triggering of injection valve 3 defective
Start value of injection valve too small
Device type not configured
Mains voltage not configured
Chiller not running
25/08/2011/ YACE0088