Table of Contents
Advertisement
Remote Control Operation
A.5
Stored Faults
Information on stored faults is returned when requested. If no stored fault exists for a
given fault number, the words "NO Fault" will be returned instead of the normal
time/date status information.
The following symbols are commonly used to define the stored faults status commands:
•
•
•
•
•
•
•
Transmit
Command:
Operational
Response:
Stored
Faults
Receive
Command:
Operational
Response:
Stored
Faults
Backup
Command:
Modem
Response:
System
Stored
Faults
A–20
#
Fault number (0 to 9). "0" is the first fault stored.
hh
Hours in 24-hour format.
mm
Minutes.
ss
Seconds.
MM
Month.
DD
Day.
YY
Year.
<add/TOSF_#'cr'
>add/TOSF_#hh:mm:ssMM/DD/YY'cr'
MOD_1_xxx'cr'
MOD_2_xxx'cr'
MOD_3_xxx'cr'
MOD_4_xxx'cr'
MOD_5_xxx'cr'
MOD_6_xxx'cr'
MOD_7_xxx'cr'
MOD_8_xxx'cr''lf']
<add/ROSF_#'cr'
>add/ROSF_#hh:mm:ssMM/DD/YY'cr'
DMD_1_xxx'cr'
DMD_2_xxx'cr'
DMD_3_xxx'cr'
DMD_4_xxx'cr'
DMD_5_xxx'cr'
DMD_6_xxx'cr'
DMD_7_xxx'cr'
DMD_8_xxx'cr''lf']
<add/SSF_Bn_#'cr'
>add/SSF_Bn_# hh:mm:ss
MM/DD/YY'cr'
COMM_xxx'cr'
MOD_CONFIG_VFY_xxx'cr'
DMD_CONFIG_VFY_xxx'cr'
ADD_xxx'cr'
MOD_CONFIG_LOAD_xxx'cr'
DMD_CONFIG_LOAD_xxx'cr'
PRIMES_ASSIGNED_xxx'cr''lf']
MU_COMM_xxx'cr'
(See Note)
MU_ADD_xxx'cr''lf']
(See Note)
SMS-7000 Modem Protection Switch
Prime #1 TX Operational Status (OK/FLT)
Prime #2 TX Operational Status (OK/FLT)
Prime #3 TX Operational Status (OK/FLT)
Prime #4 TX Operational Status (OK/FLT)
Prime #5 TX Operational Status (OK/FLT)
Prime #6 TX Operational Status (OK/FLT)
Prime #7 TX Operational Status (OK/FLT)
Prime #8 TX Operational Status (OK/FLT)
Prime #1 RX Operational Status (OK/FLT)
Prime #2 RX Operational Status (OK/FLT)
Prime #3 RX Operational Status (OK/FLT)
Prime #4 RX Operational Status (OK/FLT)
Prime #5 RX Operational Status (OK/FLT)
Prime #6 RX Operational Status (OK/FLT)
Prime #7 RX Operational Status (OK/FLT)
Prime #8 RX Operational Status (OK/FLT)
Where: n = 1 to 2 (backup modem number).
Modem Communications (OK/FLT)
Modulator Config Verify (OK/FLT)
Demodulator Config Verify (OK/FLT)
Backup Modem Address (OK/FLT)
Modulator Config Loaded (OK/FLT)
Demodulator Config Loaded (OK/FLT)
Primes Assigned to Backup (OK/FLT)
Multiplexer Unit Communications (OK/FLT)
Multiplexer Unit Address (OK/FLT)
Note: Status only returned if multiplexer unit is attached.
Rev. 3 Draft
Advertisement
Table of Contents
