Installer Lockout; Walk Test (Installer) - Member's Mark Power 832 Installation Manual

P R O G
5.28.2 Factory Default Main Panel (Software) and other Modules
Step 1 - Enter Installer Programming.
Step 2 - Enter Program Section [99X].
Step 3 - Enter the Installer Code.
Step 4 - Enter Program Section [99X] again.
The panel will take a few seconds to reset. When the keypad is operational, the default is complete.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Restore Alternate Communicator to Factory Default Programming ... Section [993]
Restore Escort5580 to Factory Default Programming ......................... Section [995]
Restore PC5132 to Factory Default Programming .............................. Section [996]
Restore PC5400 to Factory Default Programming .............................. Section [997]
Restore PC5928/5936 to Factory Default Programming ...................... Section [998]
Restore Main Panel (Software) to Factory Default Programming ....... Section [999]
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
5.29

Installer Lockout

If Installer Lockout is selected a hardware default cannot be performed. If a software default is performed all
programming will restore to factory default.
When Installer Lockout Disable is selected the panel will restore all programming to factory defaults if a
hardware or software default is performed on the main control panel.
To enable or disable Installer Lockout perform the following:
Step 1 - Enter Installer Programming.
Step 2 - Enter Program Section [99X].
Step 3 - Enter the Installer Code.
Step 4 - Enter Program Section [99X] again.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Installer Lockout Enable ......................................... Section [990]
Installer Lockout Disable ........................................ Section [991]
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
5.30

Walk Test (Installer)

The Installer Walk Test can be used to test the alarm state of each zone of the panel. The walk test cannot be
used to test zone type [24].
Before beginning the walk test, ensure the following conditions are met:
1. The panel is disarmed
2. The Keypad Blanking option is disabled (section [016]: [3])
3. The Fire Bell is Continuous option is disabled (section [014]: [8])
4. The Transmission Delay is disabled, if Transmission Delay is not required (section [370])
Fir Fir Fir Fir Fire T e T e T e Tr r r r r oubles ar e T oubles ar oubles ar oubles ar oubles are not suppor
All outputs will activate for both par All outputs will activate for both partitions during the walk test, r All outputs will activate for both par All outputs will activate for both par All outputs will activate for both par
To perform a Walk Test, do the following:
Step 1 - Enter Installer Programming
Step 2 - Enter Section [901]
When any zone is violated the panel will activate the Bell Output for two seconds, log the event to the Event
Buffer and communicate the alarm to central station. Each zone should be tested several times during the test.
Check the event buffer to ensure that all zones and FAP keys are functioning properly.
To stop the test, you must do the following:
Step 1 - Enter Installer Programming
Step 2 - Enter Section [901]
Zones do not have to be restored to stop the test. After the test is complete, check the Event Buffer to ensure
that the Audible/Silent 24-hr PGM alarms have been restored.
The Alar The Alar m Memor m Memor
The Alar The Alar The Alarm Memor m Memor m Memory is clear
Alar Alar Alarm Memor Alar Alar m Memor m Memor m Memor m Memory light will r
next time the panel is ar next time the panel is ar next time the panel is ar next time the panel is ar next time the panel is armed.
WWW.DIYALARMFORUM.COM
R A M D
e not suppor e not suppor e not supported in W e not suppor ted in W ted in W ted in Walk T ted in W alk Test. alk T alk T alk T
titions during the walk test, r titions during the walk test, r titions during the walk test, regar titions during the walk test, r
y is clear y is clear ed upon entering W ed upon entering W
y is clear y is cleared upon entering W ed upon entering W ed upon entering Walk T
y light will r y light will r y light will r y light will remain lit, but ther emain lit, but ther emain lit, but ther emain lit, but there will be no alar emain lit, but ther
med. med. med. med.
E S C R I
est. est. est. est.
egar egar egardless of pr egar
alk T alk T est mode. When the W est mode. When the W
alk T alk Test mode. When the W est mode. When the Walk T est mode. When the W
e will be no alarms in memor e will be no alar e will be no alar e will be no alar ms in memor ms in memor ms in memory y y y y . The light will tur ms in memor
38
P T I O N
dless of pr dless of pr dless of programming. dless of pr ogramming. ogramming. ogramming. ogramming.
alk T alk T est is complete, the est is complete, the
alk T alk Test is complete, the est is complete, the est is complete, the
. The light will tur . The light will turn of . The light will tur . The light will tur n of n of n off the n of f the f the f the f the
S