Automatic Arming; Keypad Lockout - Member's Mark Power 832 Installation Manual

P R O G
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Arm/Disarm Bell Squawk ........................................ Section [014], Option [1]
Bypass Status Displayed While Armed ................. Section [016], Option [7]
WLS Key Uses Access Codes ............................... Section [017], Option [1]
Opening After Alarm Keypad Ringback ................. Section [381], Option [1]
Opening After Alarm Bell Ringback ....................... Section [381], Option [2]
Closing Confirmation .............................................. Section [381], Option [4]
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
5.21

Automatic Arming

Each Partition can be programmed to auto arm at a specific time every day if it is in the disarmed condition. Up to
14 auto arm times can be programmed on the system: one for each day of the week for Partition 1 and Partition 2.
Once the auto arm times have been programmed, three items must be enabled in order to activate the auto
arming function:
1. The correct Time of Day must be programmed. For instructions on programming the time and date, see the
PC5015 Instruction Manual ("Setting the Time and Date").
2. Enter [✱][6][2] to enable (three keypad beeps) or disable (one long beep) the auto arm feature.
3. Program the auto-arm time for each day of the week, for each partition, in programming sections [180]-[193].
Items 2 and 3 ar Items 2 and 3 are pr Items 2 and 3 ar
Items 2 and 3 ar Items 2 and 3 ar
corr r r r r ect par cor cor ect par ect par
cor cor ect par ect partition (See section 2.6 "Keypad Assignment").
If the Partition 1 Auto-arm Schedule in [✱] [6] feature is enabled, users with access to partition 1 will be able to
change the partition 1 auto-arm time of day, for each day of the week. If the Partition 2 Auto-arm Schedule in [✱]
[6] feature is enabled, users with access to partition 2 will be able to change the partition 2 auto-arm time of day for
each day of the week. See section 3.4 "[✱] Commands" for a description of the [✱][6][3] menu.
When the internal panel clock matches the programmed Auto Arm Time for that day, the panel will check the
status of the partition. If the partiton is armed, the panel will do nothing until the programmed auto arm time for
the next day when it will check again.
If the partition is disarmed, the panel will sound the buzzer of all keypads assigned to the partition for one
minute. This is the auto arm pre-alert period. Please note that if there is an auto-arm time programmed for that
day, the panel will sound the pre-alert whether or not auto-arming is enabled (in the [✱][6][2] menu).
If a valid access code is entered during the auto arm pre-alert period, the Postpone Auto Arm Timer will begin.
If the timer programmed as [000], auto arming will be cancelled. If the timer is programmed from [001]-[225]
minutes, the panel will postpone auto arming for the programmed time. Once the timer is expired, the auto
arming sequence will begin again, at which point a valid access code may be entered to postpone the
procedure. Auto arming may continue to be postponed multiple times. The panel will transmit an Auto Arm
Postpone Reporting Code each time auto arming is postponed, if programmed.
If no code is entered, the panel will auto arm. If a zone is violated the panel will transmit a Partial Closing
Reporting Code if programmed to indicate the system was not secure. If the zone is restored the panel will add
the zone back into the system.
Late to Close
If the Late to Close option is enabled, the panel will transmit the Late to Close reporting code whenever the
auto-arm pre-alert sounds. If there is an auto-arm time programmed for that day, the panel will transmit the
reporting code whether or not auto-arming is enabled (in the [✱][6][2] menu). The Late to Close reporting code
must also be programmed for this feature to function.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Program Time and Date ......................................................................... [✱][6][1]
Enable Auto Arming ................................................................................ [✱][6][2]
Enable Auto Arm Day ............................................................................. [✱][6][3]
Auto Arm Times .................................................................. Sections [180]-[193]
Auto Arm Postpone Reporting Code ............................................ Section [348]
Partial Closing Reporting Code .................................................... Section [343]
Late to Close Enable/Disable ...................................... Section [017], option [5]
Late to Close reporting code ......................................................... Section [343]
Partition 1 or 2 Auto-arm Schedule in [✱][6] .... Section [017], options [2] & [3]
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
5.22

Keypad Lockout

The panel can be programmed to 'lockout' keypads if a series of incorrect access code entries are made. After
the Number of Invalid Codes Before Lockout has been reached the panel will lock out the keypad for the
Lockout Duration and log the event to the event buffer. For the duration of the lockout the panel will sound an
error tone when any key is pressed. The invalid code counter will be reset every hour.
To disable Keypad Lockout program the Number of Invalid Codes Before Lockout as [000].
If Keypad Lockout is active, the panel cannot be ar If Keypad Lockout is active, the panel cannot be ar If Keypad Lockout is active, the panel cannot be ar If Keypad Lockout is active, the panel cannot be ar If Keypad Lockout is active, the panel cannot be arme
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Number of Invalid Codes Before Lockout .............. Section [012]
Lockout Duration ..................................................... Section [012]
Keypad Lockout Reporting Code ........................... Section [338]
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
R A M D
e programmable by par e pr e pr ogrammable by partition. Pr ogrammable by par ogrammable by par
e pr ogrammable by par
tition (See section 2.6 "Keypad Assignment"). tition (See section 2.6 "Keypad Assignment").
tition (See section 2.6 "Keypad Assignment"). tition (See section 2.6 "Keypad Assignment").
WWW.DIYALARMFORUM.COM
E S C R I
tition. Pr tition. Pr tition. Program these items at a keypad assigned to the ogram these items at a keypad assigned to the ogram these items at a keypad assigned to the ogram these items at a keypad assigned to the
tition. Pr ogram these items at a keypad assigned to the
med / d / d / d / d / disar me me me disar disarmed with a keyswitch. disar disar med with a keyswitch. med with a keyswitch. med with a keyswitch. med with a keyswitch.
35
P T I O N S