Event Buffer; Swinger Shutdown; Daylight Savings Time; Keypad Backlighting - Member's Mark Power 832 Installation Manual

P R O G
exists. (See Section 5.17 "Swinger Shutdown".)
The event buffer can be viewed three different ways. It can be viewed through an LCD keypad, printed on-site using
the PC5400 printer module (See Section 5.29 "On-Site Printer") or it can be uploaded through the DLS software.
5.16.1 Viewing the Event Buffer
The following is the procedure for viewing the event buffer through the LCD keypad:
Step 1 - Enter [✱] [6] [Master Code]
Step 2 - Select 'View Event Buffer'
The keypad will display the Event Number, Partition, Time and Date of the event in question. Use the [✱] key to toggle
between this information and the event itself. Use the arrow keys (<>) to scroll through the events in the buffer.
When you have finished viewing the event buffer press the [#] key to exit.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Event Buffer Follows Swinger Shutdown ............... Section [013], Option [7]
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
5.17

Swinger Shutdown

The swinger shutdown feature is designed to prevent a runaway communicator from tying up the central station.
Different limits can be programmed for Zone Alarms, Zone Tampers and Maintenance signals. After the panel
has communicated the programmed number of transmissions for an event it will no longer report that event until
the swinger shutdown is reset.
For example, the swinger shutdown limit for Zone Alarms is set to [003]. The panel will not send more than 3
alarm signals for each zone with a swinger attribute until the swinger shutdown is reset.
The Bell output will not be activated for alarms on zones that have exceeded the limit of alarms set in the
Swinger Shutdown counter.
Swinger Shutdown will be reset when the panel is armed or every day at midnight. Once reset, the panel will
again communicate normally.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Swinger Shutdown Limit (Alarms/Tampers/Maintenance)
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
5.18

Daylight Savings Time

If the Daylight Savings Time option is enabled, the panel will follow the daylight savings time change. At 2 a.m.
on the first Sunday in April, the panel clock will be set forward one hour to 3 a.m. At 2 a.m. on the last Sunday in
October, the panel clock will be set back one hour to 1 a.m.
Events pr Events pr Events pr Events pr Events programmed to occur between 2 and 3 a.m. will not occur on the first Sunday in April. Events ogrammed to occur between 2 and 3 a.m. will not occur on the first Sunday in April. Events ogrammed to occur between 2 and 3 a.m. will not occur on the first Sunday in April. Events ogrammed to occur between 2 and 3 a.m. will not occur on the first Sunday in April. Events ogrammed to occur between 2 and 3 a.m. will not occur on the first Sunday in April. Events
pr pr pr pr programmed to occur between 1 and 2 a.m. will occur twice on the last Sunday in October ogrammed to occur between 1 and 2 a.m. will occur twice on the last Sunday in October ogrammed to occur between 1 and 2 a.m. will occur twice on the last Sunday in October ogrammed to occur between 1 and 2 a.m. will occur twice on the last Sunday in October. . . . . ogrammed to occur between 1 and 2 a.m. will occur twice on the last Sunday in October
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Daylight Savings Time ............................................ Section [017], option [6]
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
5.19

Keypad Backlighting

The keys of all the keypads can be backlit to provide easy viewing in dim lighting conditions. If the Keypad
Backlighting Option is enabled the keys will be illuminated.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Keypad Backlighting Option ................................... Section [016], Option [5]
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
5.20 Arming / Disarming Options
If the Arm/Disarm Bell Squawk option is enabled the panel will squawk the alarm output once upon arming and twice
upon disarming. The Opening After Alarm Keypad Ringback option will give you the ability to beep the keypad 8
times rapidly if the panel is disarmed after an alarm occurred. The Opening After Alarm Bell Squawk option will give
you the ability to squawk the bell output 8 times rapidly if the panel is disarmed after an alarm occurred.
Closing Confirmation, if enabled, will cause the keypad to beep 8 times rapidly after the closing reporting code
has been successfully transmitted to central station.
If the Bypass Status Displayed While Armed option is chosen, the Bypass light will be ON while the system is
armed to indicate that there are bypassed zones.
If the panel is armed using the Stay function key, or by entering [✱][9][access code], there will be no bell
squawks during entry and exit delays, except for the arm/diarm bell squawks.
If the panel is ar If the panel is armed using the Stay function key ther If the panel is ar
If the panel is ar If the panel is ar
except for the ar except for the ar
except for the ar except for the arm bell squawk. If the panel is no-entr except for the ar
no bell squawks during the exit delay, except for the ar no bell squawks during the exit delay no bell squawks during the exit delay no bell squawks during the exit delay no bell squawks during the exit delay
(and no bell squawks) when the panel is no-entr (and no bell squawks) when the panel is no-entr (and no bell squawks) when the panel is no-entry ar (and no bell squawks) when the panel is no-entr (and no bell squawks) when the panel is no-entr
If WLS Key Uses Access Codes is enabled, the disarm button will not work on wireless keys which have not been
assigned access codes. (Please see your PC5132 manual for more information on programming wireless keys.)
This option must be enabled when using a PC5132 v2.1 or earlier This option must be enabled when using a PC5132 v2.1 or earlier This option must be enabled when using a PC5132 v2.1 or earlier This option must be enabled when using a PC5132 v2.1 or earlier This option must be enabled when using a PC5132 v2.1 or earlier. Ther
must be ON. must be ON. must be ON.
must be ON. must be ON.
WWW.DIYALARMFORUM.COM
R A M D
med using the Stay function key there will be no bell squawks during the exit delay med using the Stay function key ther med using the Stay function key ther
med using the Stay function key ther
m bell squawk. If the panel is no-entr m bell squawk. If the panel is no-entr
m bell squawk. If the panel is no-entry ar m bell squawk. If the panel is no-entr
, except for the arm/disar , except for the ar , except for the ar , except for the ar
E S C R I
Section [370]
e will be no bell squawks during the exit delay e will be no bell squawks during the exit delay e will be no bell squawks during the exit delay
e will be no bell squawks during the exit delay
med using [ ✱ ][9][access code], ther
y ar y ar med using [ med using [
y armed using [ y ar med using [
m/disarm bell squawks. Ther m/disar m/disar m/disar m bell squawks. There is no entr m bell squawks. Ther m bell squawks. Ther m bell squawks. Ther
y armed. y ar y ar y ar med. med. med. med.
. Ther . Ther . Therefor . Ther
34
P T I O N
][9][access code], ther ][9][access code], ther e will be e will be
][9][access code], there will be ][9][access code], ther e will be e will be
e is no entr e is no entry delay e is no entr e is no entr y delay y delay y delay y delay
efor efor efor efore, Section [017] option [1] e, Section [017] option [1] e, Section [017] option [1] e, Section [017] option [1] e, Section [017] option [1]
S