Auto Bypass; Commands - Member's Mark Power 832 Installation Manual

K E Y
system was not Ready. When the correct code is entered and the system is Ready the panel will beep six times
rapidly and the 'Armed' light will turn on. Exit the premises through the designated entry/exit door. Other methods
of arming are available (See Section 3.4 "[ ✱ ] Commands - [ ✱ ] [0] Quick Arm, [ ✱ ] [9] Arming Without Entry Delay"
and Section 3.5 "Function Keys") .
The PC5015 has a built-in featur The PC5015 has a built-in featur The PC5015 has a built-in featur The PC5015 has a built-in feature called Audible Exit Fault. See Section 5.15 "Entr The PC5015 has a built-in featur
Options for mor Options for more infor Options for mor Options for mor Options for mor
To disarm the panel enter the premises through the designated entry/exit door. The keypad will emit a steady beep to
warn that you must disarm the system. During the last 10 seconds of entry delay the panel will pulse the keypad beeper
on and off rapidly to warn the entry delay is about to expire. Enter a valid Access Code at the keypad. If an error is
made, re-enter the code correctly. When a correct code is entered the keypad will turn off the 'Armed' light and stop the
keypad buzzer. If an alarm occurred while the panel was armed the 'Memory' light and the zones which caused the
alarm will be flashing. Press the [#] key to return the keypad to the Ready state.
3.3

Auto Bypass

When the system is armed and any zone or zone(s) on the system have been programmed as Stay/Away the
panel will immediately turn on the 'Bypass' light. It will then monitor all zones programmed as Delay 1 and Delay
2. If no delay type zone is violated by the end of the exit delay the panel will bypass all Stay/Away type zones.
The 'Bypass' light will remain on to inform the home owner that the interior protection has been automatically
bypassed by the panel. If a delay zone is violated during the exit delay, the Stay/Away zones will be active after
the exit delay expires.
This is a convenience for the user that wishes to arm the panel while at home. The user does not have to bypass
the interior manually.
The user can add the Stay/Away zones back into the system at any time by entering the [✱] [1] keypad
command (See Section 3.4 "[ ✱ ] Commands, [ ✱ ][1] Zone Bypass") .
Other methods of Stay arming are available (See Section 3.5 "Function Keys") .
3.4 [✱] Commands
✱
[ ] [1] Zone Bypassing
The [✱] [1] keypad command can be used to bypass individual zones. It can be used if the user wants to have
access to an area while the Partition is armed or to bypass a defective zone (bad contact, damaged wiring) until
service can be provided. A bypassed zone will not cause an alarm. Instructions on zone bypassing can be
found in the PC5015 Instruction Manual ("Zone Bypassing"). When the partition is disarmed, all zones bypassed
using [✱] [1] will be unbypassed, except for 24-hr zones.
If Code Required for Bypass is enabled an access code will be required to enter the Bypass mode. Only
access codes with the Bypass attribute enabled will be able to bypass zones (See Section 3.4 "[✱] Commands,
[✱] [5]").
Several features have been added to the [✱][1] zone bypassing menu:
• Bypass Recall: Press [99] while in the [✱][1] menu to recall the last set of bypassed zones.
• Clear Bypasses: Press [00] while in the [✱][1] menu to clear all bypassed zones.
• Bypass Groups: Two programmable bypass groups can be recalled when in the [✱][1] Bypass Menu. To program
a bypass group, select the zones to be bypassed. Press [95] for Group #1, or [96] for Group #2. To recall these
groups, press [✱][1] followed by [91] for Group #1 or [92] for Group #2.
If the Code Required for Bypass option is enabled, access codes 40–42 must be used to access this feature.
For two-par For two-partition systems, Bypass Gr For two-par For two-par For two-par
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Code required for bypass ....................................... Section [015], Option [5]
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
[✱ ✱ ✱ ✱ ✱ ] [2]
Trouble Display
The panel constantly monitors itself for several different trouble conditions. If a trouble condition is present, the
Trouble light will be ON and the keypad will beep twice every 10 seconds. The trouble beep can be silenced by
pressing any key on any keypad. If Bell Squawk on Trouble is enabled (section [014], option[5]), the bell will
squawk every 10 seconds when a trouble condition is present.
To view trouble conditions from an LED or fixed message LCD keypad:
1. Press [✱] [2].
2. The keypad will flash the Trouble light. The zone indicator lights corresponding to the present trouble
conditions will be ON.
When using an LCD keypad, the trouble conditions will be listed on the display; the user must simply use the
arrow (< >) keys to scroll through the list of present trouble conditions.
T T T T T r r r r r oubles can be viewed while ar oubles can be viewed while armed using the LCD keypad, pr oubles can be viewed while ar oubles can be viewed while ar oubles can be viewed while ar
later. Older keypads will incor later later . Older keypads will incor . Older keypads will incor . Older keypads will incorr r r r r ectly display "Fir
later later . Older keypads will incor
section [013], option [3] as OFF will ensur section [013], option [3] as OFF will ensur section [013], option [3] as OFF will ensur section [013], option [3] as OFF will ensur section [013], option [3] as OFF will ensure tr
WWW.DIYALARMFORUM.COM
P A D
e called Audible Exit Fault. See Section 5.15 "Entr e called Audible Exit Fault. See Section 5.15 "Entry/Exit Delay e called Audible Exit Fault. See Section 5.15 "Entr e called Audible Exit Fault. See Section 5.15 "Entr
e infor e infor e information. e infor mation. mation. mation. mation.
tition systems, Bypass Gr tition systems, Bypass Gr tition systems, Bypass Group #1 must be used on Par tition systems, Bypass Gr oup #1 must be used on Par oup #1 must be used on Par oup #1 must be used on Partition 1, and Gr oup #1 must be used on Par
med using the LCD keypad, pr med using the LCD keypad, pr med using the LCD keypad, pr med using the LCD keypad, provided the keypad is version 2.0 or
ectly display "Fir ectly display "Fir ectly display "Fire T
ectly display "Fir
C O M M
tition 1, and Gr tition 1, and Gr tition 1, and Gr tition 1, and Group #2 on Par
ovided the keypad is version 2.0 or ovided the keypad is version 2.0 or ovided the keypad is version 2.0 or ovided the keypad is version 2.0 or
e Tr r r r r ouble". If using older LCD keypads, pr e T e T ouble". If using older LCD keypads, programming ouble". If using older LCD keypads, pr ouble". If using older LCD keypads, pr
e T ouble". If using older LCD keypads, pr
e tr e troubles ar e tr e tr oubles ar oubles ar oubles ar oubles are displayed cor e displayed cor e displayed corr r r r r ectly e displayed cor e displayed cor
14
A N D
y/Exit Delay y/Exit Delay y/Exit Delay y/Exit Delay
oup #2 on Partition 2. oup #2 on Par oup #2 on Par oup #2 on Par tition 2. tition 2. tition 2. tition 2.
ogramming ogramming ogramming
ogramming
ectly ectly ectly. . . . . ectly
S