Function Keys - Member's Mark Power 832 Installation Manual

K E Y
[✱ ✱ ✱ ✱ ✱ ] [0]
Quick Arm
If the Quick Arm Enable option is enabled the panel can be armed by entering [✱][0]. This is a useful method of
arming a Partition when someone without a access code will be required to arm a Partition.
The Quick Ar The Quick Ar The Quick Ar The Quick Ar The Quick Arm featur
intended. If the feature is not enabled, the user will be r intended. If the featur intended. If the featur
intended. If the featur intended. If the featur
pr pr pr pr pressing the Stay or A essing the Stay or A essing the Stay or A essing the Stay or Away function key in or essing the Stay or A
[✱ ✱ ✱ ✱ ✱ ] [0]
Quick Exit
Quick Exit will allow someone to leave an armed premise through a Delay type zone without having to disarm
and rearm the system.
When [✱][0] is entered, if the Quick Exit Enabled option is enabled, the panel will provide a two minute window
to exit. During this time the panel will ignore the first activation of a Delay type zone. When the Delay zone is
secured the panel will end the two minute time period.
If a second Delay zone is tripped, or if the zone is not restored after two minutes, the panel will start entry delay.
If Quick Exit is used on a partitioned system, Keypad Blanking and Access Code Requir If Quick Exit is used on a par If Quick Exit is used on a par
If Quick Exit is used on a par If Quick Exit is used on a par
Blanking should be enabled. Blanking should be enabled. Blanking should be enabled. Blanking should be enabled. Blanking should be enabled.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Quick Arm Enable ................................................... Section [015], Option [4]
Quick Exit Enable ................................................... Section [015], Option [3]
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
3.5

Function Keys

There are five function keys on the PC5015 keypads labelled Stay, Away, Chime, Reset and Exit. The operation of these
keys is described below. The function is activated by pressing and holding the key for 2 seconds.
"Stay" - Stay Arm
Arms the partition to which the keypad is assigned. All Stay/Away type zones will be automatically bypassed.
Delay type zones will provide entry and exit delay. The Quick Arm feature must be enabled for this key to
function (Section [015], Option [4]) . If Quick Arming is not enabled, the user must enter their access code after
pressing the function key in order to arm the system in the Stay mode.
"Away" - Away Arm
Arms the partition to which the keypad is assigned. All Stay/Away type zones will be active at the end of the exit
delay. Delay type zones will provide entry and exit delay. The Quick Arm feature must be enabled for this key to
function (Section [015], option [4]) . If Quick Arming is not enabled, the user must enter their access code after
pressing the function key in order to arm the system in the Away mode.
"Chime" - Door Chime On/Off
Pressing the key will toggle the Door Chime feature ON or OFF. One solid beep means the feature has been
disabled, three short beeps means it has been enabled.
"Reset" - Reset Smoke Detectors
Pressing this key will cause the panel to activate for 5 seconds any output programmed as Sensor Reset. (See
Section 3.4 "[ ✱ ] Commands, [ ✱ ][7][2]").
"Exit" - Activate Quick Exit
Pressing this key will cause the panel to activate the Quick Exit feature (See Section 3.4 "[ ✱ ] Commands, [ ✱ ][0]").
3.5.1 Function Key Options
The following is a list of Function Key options:
[00] - Null Key
The key is not used and will perform no function when pressed.
[01] - Select Partition 1
Provides an easy way to select Partition 1 operation from a Partition 2 keypad. This is the same as pressing and
holding the [#] key then pressing and holding the [1] key to select Partition 1 from a Partition 2 keypad (See
Section 3.6 "Global and Partition Keypad Operation") .
[02] - Select Partition 2
Provides an easy way to select Partition 2 operation from a Partition 1 keypad. This is the same as pressing and
holding the [#] key then pressing and holding the [2] key to select Partition 2 from a Partition 1 keypad (See
Section 3.6 "Global and Partition Keypad Operation") .
[03] - Stay Arm
Same as described in Function Keys - Section 3.5.
[04] - Away Arm
Same as described in Function Keys - Section 3.5.
[05] - [✱]+[9] No-Entry Delay Arm
After this function key is pressed the user must enter a valid access code. The Partition will arm and remove
entry delay from the partition when the exit delay expires (See Section 3.4 "[ ✱ ] Commands, [ ✱ ] [9] Arming
without entry delay") .
P A D
m feature must be enabled in or m featur m featur m featur e must be enabled in order for the Stay/A e must be enabled in or e must be enabled in or e must be enabled in or
e is not enabled, the user will be r e is not enabled, the user will be requir e is not enabled, the user will be r
e is not enabled, the user will be r
way function key in order to ar way function key in or way function key in or way function key in or
titioned system, Keypad Blanking and Access Code Required to Remove titioned system, Keypad Blanking and Access Code Requir titioned system, Keypad Blanking and Access Code Requir
titioned system, Keypad Blanking and Access Code Requir
WWW.DIYALARMFORUM.COM
C O M M
der for the Stay/Away function keys to operate as der for the Stay/A der for the Stay/A der for the Stay/A way function keys to operate as way function keys to operate as way function keys to operate as way function keys to operate as
equir equired to enter their access code after equir ed to enter their access code after ed to enter their access code after ed to enter their access code after
equir ed to enter their access code after
der to ar der to arm the system in the stay or away mode. der to ar der to ar m the system in the stay or away mode. m the system in the stay or away mode. m the system in the stay or away mode. m the system in the stay or away mode.
17
A N D S
ed to Remove ed to Remove ed to Remove
ed to Remove