Fire, Auxiliary, Panic Keys; Entry/Exit Delay Options - Member's Mark Power 832 Installation Manual

P R O G
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Test Transmission Reporting Codes ...................... Section [352]
Test Transmission Time of Day .............................. Section [371]
Test Transmission Cycles ....................................... Section [370]
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
5.14

Fire, Auxiliary, Panic Keys

The emergency keys are available on all keypads. These keys must be pressed and held for 2 seconds before
they will activate. This 2 second delay is designed to help prevent accidental activation.
If the Fire Keys option is enabled, when the Fire keys are pressed and held for 2 seconds, the panel will
activate the alarm output. It pulses one second on, one second off only if option 8 of Section [013] is disabled
(Standard Fire option). If Fire Bell Continuous is selected the alarm output will sound until a code is entered,
otherwise it will sound until a code is entered or the alarm output times out. Communication of the signal to
central station is immediate.
If the Auxiliary Keys are pressed and held for 2 seconds the panel will sound the keypad beeper three times to verify
activation. The panel will beep the keypad ten times rapidly to verify communication to the central station.
If the Panic Keys are pressed and held for 2 seconds, the panel will immediately communicate the signal to
central station. If Panic Keys Audible is enabled, the panel will beep the keypad three times upon activation
and activate the alarm output until a code is entered or the alarm output times out. Otherwise the alarm will be
completely silent.
The Fir The Fir e, Auxiliary y y y y , Panic keys will operate even if Keypad Blanking and Keypad Lockout ar e, Auxiliar e, Auxiliar
The Fir The Fir The Fire, Auxiliar e, Auxiliar
(See Sections 5.22 "Keypad Lockout"and 5.23 "Keypad Blanking"). (See Sections 5.22 "Keypad Lockout"and 5.23 "Keypad Blanking"). (See Sections 5.22 "Keypad Lockout"and 5.23 "Keypad Blanking"). (See Sections 5.22 "Keypad Lockout"and 5.23 "Keypad Blanking"). (See Sections 5.22 "Keypad Lockout"and 5.23 "Keypad Blanking").
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Fire Keys Enable ..................................................... Section [015], Option [1]
Panic Keys Audible ................................................. Section [015], Option [2]
Fire Bell Continuous ............................................... Section [014], Option [8]
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
5.15

Entry/Exit Delay Options

Upon arming, the panel will begin the exit delay. If Audible Exit Delay is enabled the keypad will beep every
second until the exit delay expires. The keypad will beep rapidly for the last 10 seconds of exit delay to warn the
user the system is about to arm.
For commercial applications Bell Squawk on Exit Delay may be enabled. The panel will squawk the alarm
output once every second when the exit delay is initiated and 3 times a second for the last 10 seconds until the
exit delay expires.
Upon entry, if a Delay type zone is violated, the panel will begin entry delay. The keypad will emit a steady tone.
The keypad will pulse the keypad sounder during the last 10 seconds to warn the user the system is about to go
into alarm. If there was an alarm during the armed period, the keypad sounder will pulse for the entire entry
delay to warn the user of the previous alarm.
For commercial applications Bell Squawk on Entry Delay may be enabled. The panel will squawk the alarm
output once every second until the entry delay expires or the system is disarmed. This feature must not be used
with 2 partitions.
Since two Delay zones ar Since two Delay zones ar Since two Delay zones ar Since two Delay zones ar Since two Delay zones are pr
ar ar ar ar armed it will use the Entr med it will use the Entry Delay for the first Delay zone violated. med it will use the Entr med it will use the Entr med it will use the Entr
If the Bell Squawk During Auto Arm option is enabled, the bell will squawk while the system is auto-arming in order
to notify anyone on the premises that the system is being armed.
If Exit Delay Termination is enabled the panel will monitor the Delay zones during exit delay. If a Delay type zone is
violated then secured during the exit delay, the exit delay will be terminated and the panel will be armed immediately.
To prevent false alarms, use the built-in feature Audible Exit Fault. If a delay type zone is violated within 4
seconds after the exit delay has expired, the panel will sound the entry delay warning through the keypad and
siren alerting the customer that an improper exit was made. If the panel is disarmed within the entry delay no
signal is sent. If not, the panel will continue to sound the alarm and send a signal to central station. This feature
can be disabled in Section [013] Option [6].
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Bell Squawk During Auto Arm ................................ Section [014], Option [2]
Bell Squawk on Exit Delay ..................................... Section [014], Option [3]
Bell Squawk on Entry Delay ................................... Section [014], Option [4]
Audible Exit Delay ................................................... Section [014], Option [6]
Audible Exit Fault .................................................... Section [013], Option [6]
Exit Delay Termination ............................................ Section [014], Option [7]
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
5.16 Event Buffer
The panel will store the last 128 events that have occurred on the system. Each event will contain the time, date,
partition and the event itself along with the zone number, access code number or any other information pertaining to
the event.
If the Event Buffer Follows Swinger Shutdown feature is enabled the event buffer will not store events after the
swinger shutdown level has been reached. This will prevent the panel from overwriting the entire buffer if a problem
R A M D
, Panic keys will operate even if Keypad Blanking and Keypad Lockout ar , Panic keys will operate even if Keypad Blanking and Keypad Lockout ar
, Panic keys will operate even if Keypad Blanking and Keypad Lockout ar , Panic keys will operate even if Keypad Blanking and Keypad Lockout are active
e pr e pr e programmable, and ther e pr ogrammable, and therefor ogrammable, and ther ogrammable, and ther ogrammable, and ther
y Delay for the first Delay zone violated. y Delay for the first Delay zone violated. y Delay for the first Delay zone violated. y Delay for the first Delay zone violated.
WWW.DIYALARMFORUM.COM
E S C R I
efore two dif efor efor efor e two dif e two dif e two dif e two differ fer fer ferent Entr fer ent Entr ent Entr ent Entry Delays, when the panel is ent Entr
33
P T I O N
e active e active
e active e active
y Delays, when the panel is y Delays, when the panel is y Delays, when the panel is y Delays, when the panel is
S