JVC LET0239-001A Instructions Manual page 69

Setting the clock time
If you have performed Auto Setup (see page 13) or TV-
Linked Setup (see page 14), the clock is set automatically.
Set the clock manually in the following cases.
• When the clock time has not been set correctly by
Auto Setup, TV-Linked Setup, or Auto Channel Set.
• When the backup memory is expired.
• When you want to change Just Clock* setting yourself.
* Just Clock
Just Clock provides accurate time keeping through
automatic adjustments at regular intervals, by reading
data from a PDC signal. It also automatically adjust
the summer time setting.
• Just Clock adjusts the built-in clock every hour,
except for 23:00, 0:00, 1:00 and 2:00.
NOTES
Just Clock does not work in the following cases:
• When the unit is turned on.
• When the unit stands by for the timer recording or
Automatic Satellite Recording.
• When "L-2 SELECT" is set to "SAT."
• When the built-in clock moves more than 3 minutes slower
or faster.
• When the signal reception is not good enough.
IMPORTANT: If you turn off Just Clock, the accuracy
of the built-in clock may be reduced, which could
adversely effect timer recording. It is recommended to
turn "ON" Just Clock. However, where the clock
setting data from a PDC signal is not accurate, turn
"OFF" Just Clock.
1
Press SET UP.
2
Press 3 or 2 to move
press ∞.
3
Press 3 or 2 to move
press ENTER.
4
Press ∞ or 5 to move
ENTER.
The Clock Set screen appears.
[ENTER]
[SET UP]
5
Press ∞ or 5 to set the current time, then press
ENTER.
• If you hold ∞ or 5, the time changes in 30-minute
intervals.
to "INITIAL SET UP," then
to "INITIAL SET," then
to "CLOCK SET," then press
[ENTER]
[SET UP]
6
Press ∞ or 5 to set the date, then press ENTER.
• If you hold ∞ or 5, the date changes in 15-day
intervals.
7
Press ∞ or 5 to set the year, then press ENTER.
8
Press ∞ or 5 to set Just Clock, then press ENTER.
• Each time you press ∞ or 5, Just Clock turns "ON"
and "OFF" alternately.
9
Press ∞ or 5 to select the station from which you
receive the clock setting signal.
• Select the station transmitting the clock setting
signal—BBC1, BBC2,Channel 4, etc.
10
Press SET UP twice to finish the setting.
Setting the Guide Program number for
VIDEO P + System
®
LUS
Normally, Auto Setup (see page 13), TV-Linked Setup (see
page 14) or Auto Channel Set (see page 70) sets the
Guide Program numbers automatically.
Set the Guide Program numbers manually in the
following cases.
• When the VIDEO P +
LUS
correct programme position number for the station you
want to record.
• When you add a new station manually.
• When you want to record a satellite programme using
®
the VIDEO P + system (Set the Guide Program
LUS
numbers for all satellite broadcast stations which can
be received on your satellite receiver.)
Guide programme number
"Guide programme (GUIDE PROG) number" refers to
the assigned TV station numbers in your area for the
®
VIDEO P + system. The Guide Program numbers
LUS
can be found in most TV listings.
Example: When inputting Guide Program number 4 for
CH4.
1
Press SET UP.
2
Press 3 or 2 to move
press ∞.
3
Press 3 or 2 to move
press ENTER.
4
Press ∞ or 5 to move
"GUIDE PROG SET," then
press ENTER.
5
Press ∞ or 5 to enter the
Guide Program number for
the desired station as
shown in the TV listings,
then press ENTER.
69
®
system cannot select the
to "INITIAL SET UP," then
to "INITIAL SET," then
to
[ENTER]
[SET UP]