Specifications - Panasonic MINAS-BL GP series Instructions Manual

Conformance to EC directive and UL standard
Surge absorber
• DV0P4190
ø4.2±0.2
UL-1015 AWG16
1 2
41±1
• DV0P1450
ø4.2±0.2
UL-1015 AWG16
1 2 3
41±1
Noise filter for control signals
• DV0P1460
39±1
34±1
mass: 62.8g
Recommended circuit breaker (MCCB)
Made by Sensata Technologies Japan Limited:
Type IELH-1-11-63-5A-M (single phase)
(Rated current 5A, cutoff characteristics DELAY63)
• Recommended cutoff characteristics: DELAY61-63
[Unit: mm]
Circuit diagram
[Unit: mm]
Circuit diagram
[Unit: mm]
Type IELH-1-111-63-5A-M (3-phase)
－ 94 －

Specifications

• Brushless motor specifications
Item
Flange size
80 mm sq.
Motor model No. MBMU5AZAB
Motor rated output (W) 50
Voltage for 100 V/200 V
Rated torque (N･m) 0.16
Starting torque
*1
0.24
(N･m)
Rated input current
0.53 0.53
(A(rms))
Moment of inertia of
0.12
rotor（×10 kg･m ）
−4 2
Rating
Rated rotation speed
*2
（r/min）
maximum rotation
speed （r/min）
Speed control range
(r/min)
Axial runout
0.05 mm or less at the position of 3 mm from the shaft end
Bearing
Measure the insulation resistance with 500 V Megger. It must be above 20 MΩ
Insulation resistance
Measuring position: Between power input line (L1, L2,L3) and grounding wire
Isolation voltage 1500 VAC, 1 minute, 10 mA or less (between power and grounding wire)
Ambient temperature
* Ambient temperature is measured at a distance of 5 cm from the motor.
Ambient humidity
Altitude
Vibration
Impact
Motor insulation class
Storage temperature
*Extreme temperatures are permissible only for short period such as during transportation.
Storage humidity
Protection structure
Number of poles
Motor mass (kg) 0.7
*1 Representative value
*2 Motor shaft speed: to be multiplied by the reduction ratio when the gear head is used.
*3 Excluding the shaft pass-through section and cable end connector.
* Should conform to the test conditions specified in EN standard (EN60529 and EN60034-5).
Not suitable for application where watertightness is required over a prolonged period, even if
frequently washed.
• Standard characteristics measurement conditions are temperature of 25 °C and relative humidity of
65%, and may be extended to 5 to 35 °C and 45 to 85% RH.
Specifications
90 mm sq.
MBMU9A1AB MBMU9A2AB MBMU1E1AB MBMU1E2AB
90 130
for 100 V for 200 V for 100 V
0.29 0.41
0.43 0.62
1.00 0.50 1.30
0.27 0.36
Continuous
3000
4000
30 to 4000
Ball bearing
−10 ℃ to +40 ℃ (free from freezing)
20 to 85% RH (free from condensation)
Lower than 1000m
4.9 m/s or less (10 to 60 Hz) X, Y, Z
2
Lower than 98m/s 2
130(B) (UL certified 105 (A))
–20˚C to 60˚C ( free from condensation)
85%RH or below (free from condensation)
IP65 *3
8
1.0
－ 95 －
for 200 V
0.72
1.2