CORRECT CRAFT Super Sport User Manual page 20

1. Make sure the launch control system seacocks are open. Empty the system
completely using the drain pumps.
2. On boats that do not have the storage locker tank, open the rear storage
compartments, remove the two drain hoses from their through-hull fittings,
remove the two vent hoses from their through-hull fittings, unplug the drain
pump, and remove each tank from the boat. Turn the tanks upside down and
allow all the water present to drain out the vent hoses. Be sure all the water
has drained from the pumps and hoses still in the boat.
If the boat is equipped with a storage locker tank, open the locker lid and
remove the drain plug from the back side of the tank. Allow the tank to drain
completely raising and lowering the bow of the boat to insure complete
drainage. Replace the drain plug.
3. Reinstall each tank by reversing the above procedure.
Optional Correct Craft Cruise Operating Instructions
Turn system ON (light blinks slowly, indicating system is armed)
Drive to desired speed, prese ENGAGE and the system takes control of the
throttle (Light stays on steady)
Pull back on the throttle and the system disengages. (Light blinks rapidly,
indicating RESUME function is ready)
Accelerate again and the system resumes control automatically at the last
speed used.
RESUME key feature will recall the last speed used even if the system was
shut off, completely powered down or the DISENGAGE function was used.
To go back to the previous speed, press RESUME and drive to the desired
speed.
Press both keys and the system will DISENGAGE,but remains armed. (Light
blinks slowly) This feature may be used when the operator wishes to go to
manual driving. To return to the last speed used, press the RESUME key and
drive to the desired speed. If the speed is to be changed, drive to that speed
and press engage.
INCREASE / DECREASE key can be pressed when the system is engaged to
change speed in 25 RPM increments to fine tune the speed.
User tips:
Always return to neutral and let the engine idle for two or three seconds before
turning the engine off Regularly check the black servo knob on the control
unit to make sure it is turned snugly in a clockwise direction. To do this, turn
the engine off and lift the top half of the engine box. Please note, the servo
knob cannot be moved if the engine is on.
1.16
1. Make sure the launch control system seacocks are open. Empty the system
completely using the drain pumps.
2. On boats that do not have the storage locker tank, open the rear storage
compartments, remove the two drain hoses from their through-hull fittings,
remove the two vent hoses from their through-hull fittings, unplug the drain
pump, and remove each tank from the boat. Turn the tanks upside down and
allow all the water present to drain out the vent hoses. Be sure all the water
has drained from the pumps and hoses still in the boat.
If the boat is equipped with a storage locker tank, open the locker lid and
remove the drain plug from the back side of the tank. Allow the tank to drain
completely raising and lowering the bow of the boat to insure complete
drainage. Replace the drain plug.
3. Reinstall each tank by reversing the above procedure.
Optional Correct Craft Cruise Operating Instructions
Turn system ON (light blinks slowly, indicating system is armed)
Drive to desired speed, prese ENGAGE and the system takes control of the
throttle (Light stays on steady)
Pull back on the throttle and the system disengages. (Light blinks rapidly,
indicating RESUME function is ready)
Accelerate again and the system resumes control automatically at the last
speed used.
RESUME key feature will recall the last speed used even if the system was
shut off, completely powered down or the DISENGAGE function was used.
To go back to the previous speed, press RESUME and drive to the desired
speed.
Press both keys and the system will DISENGAGE,but remains armed. (Light
blinks slowly) This feature may be used when the operator wishes to go to
manual driving. To return to the last speed used, press the RESUME key and
drive to the desired speed. If the speed is to be changed, drive to that speed
and press engage.
INCREASE / DECREASE key can be pressed when the system is engaged to
change speed in 25 RPM increments to fine tune the speed.
User tips:
Always return to neutral and let the engine idle for two or three seconds before
turning the engine off Regularly check the black servo knob on the control
unit to make sure it is turned snugly in a clockwise direction. To do this, turn
the engine off and lift the top half of the engine box. Please note, the servo
knob cannot be moved if the engine is on.
1.16