Viewfinder Adjustment; External Monitor Adjustment - JVC GY-DV5100 Instructions Manual

6. SETTING AND ADJUSTMENTS BEFORE SHOOTING

6-3 Viewfinder Adjustment

2.
1.
Eyepiece
2. 1.
Eyepiece
1.
focusing ring
3.
3.
CONT BRIGHT

6-4 External Monitor Adjustment

Color video monitor
1.
LINE OUT
CH-1
Y/C OUT MONITOR OUT
3.~8.
CH-2
2.
POWER VTR
ON OFF
■ SMPTE type color bars
White Yellow Cyan Green Magenta Red Blue
1 2 3 4 5 6 7
Blue Black Magenta Black Cyan Black White
8 9 0 A B C D
Black White Black
E F G H I J K
48
1.
Adjust the position and angle of the viewfinder.
2.
Diopter adjustment
Rotate the eyepiece focusing ring until the viewfinder screen
image is clearly visible.
3.
Brightness and contrast adjustment
When the ambient brightness changes, etc., the brightness
and contrast of the viewfinder screen can be adjusted with
the BRIGHT and CONT controls.
MEMO:
The screen size of the viewfinder can be changed by
selecting the desired size with the ASPECT RATIO item
on the CAMERA OPERATION menu screen (4:3 or
LETTER).
Display the camera built-in color bar signal on the video monitor
and adjust the colors, contrast and brightness.
1.
Connect a color video monitor to the MONITOR OUT
connector of the GY-DV5100.
2.
Set the COLOR BARS/CAMERA/AUTO KNEE switch to
BARS to output the color bar signal (SMPTE type color
bars).
3.
Set the monitor's BLUE CHECK function to ON while the
color bars are being displayed so that the screen turns
entirely blue and the color bars become blue stripes.
4.
Adjust the CHROMA control of the monitor so that there is
no difference in brightness between the color bars 1 and
8, 7 and D.
5.
With the BLUE CHECK function ON, adjust the PHASE
control of the monitor so that there is no difference in
brightness between the color bars 3 and 0, 5 and B.
6.
If the phase control adjustment above causes a difference
in brightness between the color bars 1 and 8, 7 and D,
start again from the CHROMA control adjustment in step 4 .
7.
Set the monitor's BLUE CHECK function to OFF to switch
the monitor back to the standard screen (R, G and B will all
appear).
8.
Use the monitor's brightness control to adjust so that the
color bars H and I disappear but J is visible.
6. SETTING AND ADJUSTMENTS BEFORE SHOOTING
6-3 Viewfinder Adjustment
2.
1.
Eyepiece
2. 1.
Eyepiece
1.
focusing ring
3.
3.
CONT BRIGHT
6-4 External Monitor Adjustment
PUSH
Colour video monitor
1.
LINE OUT
CH-1
Y/C OUT MONITOR OUT
3.~8.
CH-2
2.
POWER VTR
ON OFF
■ EBU type colour bars
1 2 3 4 5 6 7 8
E-48
1.
Adjust the position and angle of the viewfinder.
2.
Diopter adjustment
Rotate the eyepiece focusing ring until the viewfinder screen
image is clearly visible.
3.
Brightness and contrast adjustment
When the ambient brightness changes, etc., the brightness
and contrast of the viewfinder screen can be adjusted with
the BRIGHT and CONT controls.
MEMO:
The screen size of the viewfinder can be changed by
selecting the desired size with the ASPECT RATIO item
on the CAMERA OPERATION menu screen (4:3 or
LETTER).
Display the camera built-in colour bar signal on the video monitor
and adjust the colours, contrast and brightness.
1.
Connect a colour video monitor to the MONITOR OUT
connector of the GY-DV5100.
2.
Set the COLOR BARS/CAMERA/AUTO KNEE switch to
BARS to output the colour bar signal (EBU type colour bars).
3.
Set the monitor's BLUE CHECK function to ON while the
colour bars are being displayed so that the screen turns
entirely blue and the colour bars become blue stripes.
4.
Adjust the CHROMA control of the monitor so that there is
no difference in brightness between the colour bars 1 and
7.
5.
With the BLUE CHECK function ON, adjust the PHASE
control of the monitor so that there is no difference in
brightness between the colour bars 3 and 5.
6.
If the phase control adjustment above causes a difference
in brightness between the colour bars 1 and 7, start again
from the CHROMA control adjustment in step 4 .
7.
Set the monitor's BLUE CHECK function to OFF to switch
the monitor back to the standard screen (R, G and B will all
appear).