Power Supply - JVC GY-DV5100 Instructions Manual

4. POWER SUPPLY

The GY-DV5100 is operable with AC power supply or battery pack.
4-1 AC Operation
Use the JVC AA-P250 AC power adapter (max. rated output 12.5 V DC, 3.5 A) as the AC power supply.
AA-P250
PHONES
DC cable DV INT
DC IN
DC OUT
CH-1
AC power adapter
4-2 Battery Pack Operation (Optional)
The GY-DV5100 can be operated with the following battery packs.
■ Flat shape type battery pack
■ Anton-Bauer battery pack
● DIONIC 90
● Propack 13/14 Series
● Trimpack 13/14 Series
● Magnum 13/14 Series
● Compack 13/14 Series
● When the DC cable is connected to the DC IN connector, the power supply from the battery pack is interrupted and the power
starts to be supplied through the DC IN connector.
● Do not connect or disconnect the DC cable while operating with a battery pack.
The following symptoms may occur if the DC cable is connected or disconnected while operating with a battery pack.
• The power is cut off for a moment when the DC cable is disconnected.
• Noise to the video and audio signals occurs. Audio signal are muted.
● When operation is continued with DC input after the battery pack capacity has been used up, set the POWER switch to OFF
after the DC power is applied. Then switch ON again.
● If the GY-DV5100 is left with the battery pack attached, a small amount of power is consumed even if the POWER
switch on the GY-DV5100 is set to OFF. Remove the battery pack when the GY-DV5100 is not going to be used.
Do not use any power source with large fluctuations in the
power source voltage, power sources generating noise,
such as ripples or power sources with lower voltage.
1.
After making sure that the power switches of the GY-DV5100
and of the AA-P250 are set to OFF, connect the DC cable
TALLY
from the AA-P250 to the DC IN connector of the GY-DV5100
as shown in the illustration.
CH-2
REAR AUDIO IN
2.
Set the CHARGE/CAMERA switch of the AA-P250 to
CAMERA.
3.
Press the POWER switch of the GY-DV5100 to ON. Power
is supplied to the VTR section and the camera.
* For details, read the instruction manual of the AA-P250.
MEMO:
Do not remove or connect the DC cable while recording is
being performed.
* A flat shape type battery pack cannot be connected directly
to the camera. It is necessary to mount the optional battery
case.
Battery case: SCV2978-002
See "Attaching the NP-1B type Battery" on page 36.
4. POWER SUPPLY
The GY-DV5100 is operable with AC power supply or battery pack.
4-1 AC Operation
Use the JVC AA-P250 AC power adapter (max. rated output 12.5 V DC, 3.5 A) as the AC power supply.
AA-P250
AC power adaptor
4-2 Battery Pack Operation (Optional)
The GY-DV5100 can be operated with the following battery packs.
■ Flat shape type battery pack
■ Anton-Bauer battery pack
● DIONIC 90
● Propack 13/14 Series
● Trimpack 13/14 Series
● Magnum 13/14 Series
● Compack 13/14 Series
● When the DC cable is connected to the DC IN connector, the power supply from the battery pack is interrupted and the power
starts to be supplied through the DC IN connector.
● Do not connect or disconnect the DC cable while operating with a battery pack.
The following symptoms may occur if the DC cable is connected or disconnected while operating with a battery pack.
• The power is cut off for a moment when the DC cable is disconnected.
• Noise to the video and audio signals occurs. Audio signal are muted.
● When operation is continued with DC input after the battery pack capacity has been used up, set the POWER switch to OFF
after the DC power is applied. Then switch ON again.
● If the GY-DV5100 is left with the battery pack attached, a small amount of power is consumed even if the POWER
switch on the GY-DV5100 is set to OFF. Remove the battery pack when the GY-DV5100 is not going to be used.
35
Do not use any power source with large fluctuations in the
power source voltage, power sources generating noise,
such as ripples or power sources with lower voltage.
1.
After making sure that the power switches of the GY-DV5100
and of the AA-P250 are set to OFF, connect the DC cable
from the AA-P250 to the DC IN connector of the GY-DV5100
as shown in the illustration.
PHONES TALLY
DC cable INT
DV
DC IN 2.
DC OUT
Set the CHARGE/CAMERA switch of the AA-P250 to
CH-1 CH-2
REAR AUDIO IN
CAMERA.
3.
Press the POWER switch of the GY-DV5100 to ON. Power
is supplied to the VTR section and the camera.
* For details, read the instruction manual of the AA-P250.
MEMO:
Do not remove or connect the DC cable while recording is
being performed.
* An Anton-Bauer battery pack cannot be connected directly
to the GY-DV5100. It is necessary to mount the optional
battery holder.
Battery holder: Anton-Bauer QR JVC DIGI
For details on how to mount the battery holder, see page
37.
E-35