Baumatic BVP460SS User Manual
  1. Manuals
  2. Brands
  3. Baumatic Manuals
  4. Kitchen Appliances
  5. BVP460SS
  6. User manual
Baumatic BVP460SS User Manual

Baumatic BVP460SS User Manual

Vacuum-packer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
BVP460SS Vacuum-
Packer
He

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BVP460SS and is the answer not in the manual?

Questions and answers

Related Manuals for Baumatic BVP460SS

Summary of Contents for Baumatic BVP460SS

  • Page 1 BVP460SS Vacuum- Packer...
  • Page 2 USER MANUAL FOR YOUR BAUMATIC BVP460SS Vacuum- Packer NOTE : This User Instruction Manual contains important information, including safety & installation points, which will enable you to get the most out of your appliance. Please keep it in a safe place so that it is easily available for future reference. for you or any person not familiar with the operation of the appliance.

  • Page 3: Table Of Contents

    Contents Environmental note Important safety information 5–6 Specifications of your vacuum-packer Using your vacuum-packer 8-10 Before switching on Storing vacuum-packed products Loading the vacuum-packer Tips on vacuum-packed food preservation 9-10 Turning on the appliance and setting a vacuum-packing cycle 11-21 Control panel Switching the appliance on Preserving cycles for bags preparation...

  • Page 4: Environmental Note

    Environmental note Note : Before discarding an old appliance, switch off and disconnect it from the power supply. Cut off and render any plug useless. Cut the cable off directly behind the appliance to prevent misuse. This should be undertaken by a competent person. Disable the door lock to make sure that children cannot get stuck inside the appliance.

  • Page 5: Important Safety Information

    Important safety information Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of the information contained in this booklet, please contact the Baumatic Advice Line.
  • Page 6 o Do not attempt to use your appliance outdoors or any place where it is likely to come into contact with the elements. o Before cleaning the appliance or performing maintenance work, ensure that the appliance has been disconnected from your mains supply.

  • Page 7: Specifications Of Your Vacuum-Packer

    Specifications of your vacuum-packer o 4 x vacuum-packing cycles o LED display o Electronic control operation o Net volume: 17 litres o Pump oil substitution indicator o Insufficient vacuum signal Dimensions of appliance Height: 460 mm Width: 597 mm Depth: 550 mm Dimensions of aperture* Height:...

  • Page 8: Using Your Vacuum-Packer

    Using your Baumatic vacuum-packer Before switching on o Make sure that it has been installed by a suitably qualified person, information contained Baumatic’s installation instructions. o Before using the appliance, it is recommended that you clean the vacuum chamber and lid using a soft cloth which has been dampened with tap water.

  • Page 9: Loading The Vacuum-Packer

    Loading the vacuum-packer o The food should be previously prepared inside the special vacuum-pack bags (for cooking or preserving), or inside rigid vacuum-pack containers (“vacuum-pack boxes”). o The bag or container should be positioned inside the vacuum chamber where the evacuation of the air takes place and, in the case of vacuum-pack bags, they are sealed.
  • Page 10 meat and cool it properly before vacuum-packing. Keep it in the fridge at a temperature of not more than 3°C. o For hard cheeses, such as Parmesan, Pecorino etc. it is not necessary to undertake any special procedures. For soft cheeses, in order to avoid them being squashed, it is a good idea to wrap them in cellophane or to opt for preserving them in vacuum-pack containers.

  • Page 11: Turning On The Appliance And Setting A Vacuum-Packing Cycle

    Turning on the appliance and setting a vacuum- packing cycle Control panel 1) Control buttons 2) LED displays o Press to select the preserving cycle. The cycle lasts approximately three minutes. The vacuum inside the led bags, in best conditions, can reach 0.002 - 0.005 bar. o Once the cycle has started, if the button is pressed again, the appliance moves directly to soldering the bags.

  • Page 12: Switching The Appliance On

    witching the appliance on o Turn the appliance on using the ON / OFF switch located on the right of the main body of the machine. o A short beep is emitted whic h indicate s the appliance is in “initial start-up”...
  • Page 13 o Place the bag on the grill, in a central position on the soldering bar (A), in order for the open flap to overlap it by around 2 cm. o When packing liquid products, do not fill the bag more than half full.
  • Page 14 The cycle proceeds automatically in the following order: o The evacuation phase signalled preservation cycle button blinking for around two minutes. o The soldering phase is signalled by the LED of the preservation cycle button coming on. This phase lasts approximately nine seconds.

  • Page 15: Cooking Cycle For Bags

    Cooking cycle This is a forced vacuum level. The air is removed both from the food and its internal parts, in such a way as to obtain the transmiss ion of heat from the outside to the inside of the product in the next cooking phase in the steam oven.

  • Page 16: Tips On Vacuum-Packing Bags

    o At the end of the cycle, an acoustic short beep will sound which indicates that the appliance is ready for a new cycle. By pressing the cooking cycle button during the air evacuation phase, the appliance will pass to the soldering phase. The cycle can be interrupted early by pressing the stop button.

  • Page 17: Preserving Cycles For Containers Preparation

    Preserving cycles for containers Preparation In all cases where liquid foods are to be vacuum-packed, the containers can be filled to a maximum of ¾ of their usable volume. o Based on the type of container chosen, the corresponding jar cycle will be set e.g.

  • Page 18: Brief Preserving Cycle For Containers

    Brief preserving cycle for containers This cycle used plastic (polycarbonate) containers. This cycle lasts approximately one minute. o After following the steps in the preparation section, outlined on page 17, close the lid by pressing lightly on its front and selecting the brief preserving cycle button at the same time.

  • Page 19: Long Preservation Cycle For Containers

    The vacuum obtained by this cycle is around 80% of the vacuum which can be reached and is suitable for plastic containers and not intended for professional use. Long preserving cycle for containers This cycle is used for rigid and resistant forced vacuum-pack containers (e.g.

  • Page 20: Tips On Vacuum-Packing Containers

    The cycle can be interrupted early by pressing the stop button. The vacuum obtained by this cycle is around 100% of the vacuum which can be reached and, consequently, is only suitable for very resistant and thick plastic containers or those made of glass or stainless steel.

  • Page 21: Stopping A Cycle In Progress

    Stopping a cycle in progress o By pressing the stop button, an acoustic signal will warn that cycle will immediately interrupted. In this case, the appliance will not carry out the soldering phase and the chamber will be decompressed. o After the discharge phase all the LED’s will revert to the initial start-up mode.

  • Page 22: Cleaning The Vacuum Chamber

    Cleaning the vacuum chamber o In order to guarantee the hygiene and quality of the packaged food products, internal cleaning of the vacuum chamber should be undertaken after each use. o The shape of the chamber enables fast cleaning. The use of a soft cloth or non-abrasive sponge is recommended and a neutral detergent.

  • Page 23: Dehumidifying The Pump Oil

    o Clean using a soft cloth or non-abrasive sponge and a neutral detergent. o When finished, insert the bar into the two screws (B) centering the two holes on the lower part of the bar and ensuring that it is correctly inserted.

  • Page 24: Signals And Warnings

    Baumatic Ltd declines any responsibility for work carried out on the appliance which is not in line with the instructions reported in this manual. Signals and warnings Pump oil substitution warning o The vacuum-packer equipped with high-performance vacuum pump, which is lubricated by special oil, designed for this appliance.

  • Page 25: Installation

    If the fault persists then call the Baumatic Ltd Customer Care Helpline. WARNING: Do not attempt to repair or adjust the appliance yourself. It could be dangerous and affect your guarantee. Only authorised and qualified technicians should be entrusted to do...

  • Page 26: Unpacking The Vacuum-Packer

    Unpacking the vacuum-packer Handling of the appliance should always be carried out by two people, using the stainless steel handles inserted in the packaging. Use sticky tape to hold them securely. They can be hooked onto the two sides of the external container and should be inserted into the two upper holes as shown in the diagrams below: The handles should be inserted completely so that the two ends...
  • Page 27 Then remove the polystyrene blocks from the top and using the protective gloves lift the appliance with the help of the two handles. o After removing the packaging, immediately check the appliance for transport damage. If faults are found, do not operate the appliance and contact the retailer.

  • Page 28: Matriculation Plate Data

    Matriculation plate data The matriculation plate data are positioned on: o 1 label on the external cardboard packaging. o 2 device plates, positioned at the centre top of the container and below the drawer. WARNING: Do not remove, damage or adjust the matriculation plate attached to the device.
  • Page 29 The blue wire must be connected to the terminal marked “N” (neutral), or coloured black. The green and yellow wire must be connected to the terminal marked “E” (earth), or by the earth symbol, or coloured green and yellow. o When the connection is completed, no stray strands or cut wire should be present.

  • Page 30: Installing Your Vacuum-Packer

    Installing your vacuum-packer WARNING: unit (column support base) must solidly anchored to the walls using screws or plugs of the right size. o The vacuum packer should positioned inside the unit. o The appliance is supplied with special brackets to fix the container to the inside of the compartment.

  • Page 31: Installing The Appliance Into A Housing Unit

    The power cable is 150 cm long and due to problems connected with overheating, it is not possible to use extension cords to lengthen it. Bear in mind the position of the sockets when locating your vacuum-packer. Installing the appliance into a housing unit o Please use the above diagram as a guide when fitting the appliance into a housing unit.
  • Page 32 o Fix the blockage brackets on the two internal sides of the compartment using eight 4.5 x 16 screws for the chipboard panels. o The brackets must rest on the horizontal surface and be vertically aligned with the two sides of the unit. o Place the appliance on the horizontal surface and insert it 5 cm from the edge of the unit.
  • Page 33 o The appliance must be central within the compartment. o Open the drawer to around 15 cm and screw the device to the blockage brackets using the four self-tapping screws that are supplied, using a short Phillips cross screwdriver. o If you have not attached the door, first proceed with the two lower screws which can be tightened with the drawer closed.
  • Page 34 Only extract the drawer completely after fixing the appliance into the unit. o In order to fix the door, put the seal included with the vacuum- packer between the appliance panel and the door, inserting it between the upper edge of the vacuum-packer and the door. Neither glue nor adhesives are necessary.

  • Page 35: Final Checks

    Final checks Before switching the appliance on, it is recommended that you carry out the following checks: o If the vacuum-packer has been transported in a non- vertical position e.g. on it’s back, or it has been tipped during installation, check the level of the oil in the pump using the inspection hole.

  • Page 36: Troubleshooting

    If, on switching the machine back on, the same problem occurs call the Baumatic Ltd Customer Care Helpline to arrange for an engineer to replace the power board. The stop button Insufficient vacuum in the...
  • Page 37 Or any installation other than the one specified by Baumatic Ltd. has been completed. Please refer to the conditions of guarantee that appear on the...

  • Page 38: Contact Details

    United Kingdom Baumatic Ltd., Czech Republic Baumatic Buildings, Baumatic CR spol s.r.o. 6 Bennet Road, Průmyslová zóna Sever 696 Reading, Berkshire 460 11 Liberec 11 RG2 0QX Czech Republic United Kingdom +420 483 577 200 Sales Telephone (0118) 933 6900 www.baumatic.cz...
  • Page 40 29 29...

Table of Contents