Simulations, Fax Software Switch; Simulation - Sharp MX-FXX1 Service Manual

[5] SIMULATIONS, FAX SOFTWARE SWITCH

MXFXX1

1. Simulation

A. General
There are the following simulation functions for grasping the
machine operating conditions, troubleshooting, early detection of
trouble causes, speedy setting and adjustments, and improve-
ments in servicing.
1) Various adjustments
2) Setting of the specifications and functions
3) Canceling troubles
4) Operation check
5) Counters check, setting, clear
6) Machine operating conditions (operation hysteresis), data
check, clear
7) Various (adjustments, setting, operation, counters, etc.) data
transfer
The operating procedures and displays depend on the form of the
operation panel of the machine.
B. List of simulation codes
Code
Main Sub
13 -- Used to cancel the self-diag "U1" trouble.
22 11 Used to check the use frequency (send/receive) of FAX.
24 10 Used to clear the FAX counter.
46 39 Used to execute the image send sharpness adjustment.
40 Used to execute the FAX exposure adjustment. (Collective adjustment of all the
modes).
41 Used to execute the FAX exposure adjustment (Normal).
42 Used to execute the FAX exposure adjustment (Fine text).
43 Used to execute the FAX exposure adjustment (Super Fine).
44 Used to execute the FAX exposure adjustment (Ultra Fine).
45 Used to execute the FAX exposure level adjustment and the individual setting
(600DPI).
50 27 Used to adjust the image loss of scanned image in the FAX/Scanner mode.
66 1 Used to display the FAX-related soft SW on the LCD to allow changing the soft SW
while checking with the LCD.
2 Used to enter a country code and set the default value for the country code.
3 Used to execute the read/write check of EEPROM on the MODEM controller, SDRAM,
SRAM on the MFP controller, and flash ROM, and to display the results.
4 Used to send the selected signals to the line and the main unit speaker. (Send level:
max.)
5 Used to send the selected signal to the line and the main unit speaker. (Send level:
Soft SW setting) (For the kinds of send signals, refer to PART1 and PART2 of SIM66-
04.)
6 Used to print the confidential registration check table (BOX NO., BOX name,
passcode. (If there is no confidential registration, no print is made.)
7 Used to output all image data saved in the image memory. (Confidential data are also
outputted.)
8 Used to send the selected sound messages to the line and the speaker. (Send level:
Max.)
9 Used to send the selected sound message to the line and the speaker. (Send level:
max.)
* For details of sound messages, refer to the sound message table of SIM66-08.
10 Used to clear all image data saved in the FAX image memory. (The confidential data
are also cleared.)
Function (Purpose)
MX-FXX1 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 1
Service Manual
(1) Basic operation
a. Starting the simulation
* Entering the simulation mode
Copy mode key ON → Program key ON → Asterisk (*) key
1)
ON → CLEAR key ON → Asterisk (*) key ON → Ready for
input of a main code of simulation
Entering a main code with the 10-key → START key ON
2)
Entering a sub code with the 10-key → START key ON
3)
4) Select an item with the scroll key and the item key.
5) The machine enters the mode corresponding to the selected
item.
Press START key or EXECUTE key to start the simulation
operation.
To cancel the current simulation mode or to change the main
code and the sub code, press the user setup key.
* Canceling the simulation mode to return to the normal mode
1) Press CA key.
(Note for the simulation mode)
Do not turn OFF the power switch on the operation panel when the
machine is in the simulation mode.
If the power switch should be turned OFF in the simulation mode, a
malfunction may be resulted. In this case, turn OFF/ON the main
power source.
Section
FAX
FAX
–
FAX
MFP/FAX
MFP/FAX
MFP/FAX
MFP/FAX
MFP/FAX
FAX
FAX/Scanner
Setting
Setting
Operation test/Check
Operation test/Check
Operation test/Check
Data output/Check
Data output/Check
Operation test/Check
Operation test/Check
Data clear
Purpose
Clear/cancel (Trouble etc.)
Adjustment/Setup/Operation
data check
Data clear
Adjustment
Adjustment
Adjustment
Adjustment
Adjustment
Adjustment
Adjustment
Adjustment
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX
FAX