Soft Switch - Sharp AR-FX7 Service Manual

[7] SOFT SWITCH

1. FAX soft switch setting change quick reference table
Large item Middle item
Dialing Remote machine
call disable
Signal detection
Redial In case of an error
In case of an error
When busy
When busy
Arrival (Call-in) When CI detection
disable
External Setting of an
telephone external telephone
connected
Remote switch
number
Remote switch
setting
Communication General
SG3
Transmission G3/SG3
SG3
G3
Reception G3/SG3
SG3
G3
Switch content
Pause time Default setting
Dial call signal Default setting
DTMF-related item None
None
None
Pulse (10PPS) None
Busy tone detection None
Busy tone detection cycle None
Dial tone detection None
Resend interval Transmitter
function setting
Number of times of resend Transmitter
function setting
Resend interval Transmitter
function setting
Number of times of resend Transmitter
function setting
CI detection None
CI signal OFF detection time None
Yes/No Default setting
Entry of a 2-digit number Default setting
Yes/No None
Send level None
JBIG mode None
V34 mode function setup None
V34 symbol rate None
DIS reception check One-touch/
Reduction, etc.
Line equalizer None
V34 send speed One-touch/
Reduction, etc.
Manual send V34 None
V29 no modulation carrier None
Modem send speed One-touch/
Reduction, etc.
RTN reception error None
CSI transmission None
Maximum reception length None
Proxy reception None
EQM dispersion inhibit None
V34 reception speed None
Countermeasure against None
echo in reception
Modem speed in reception None
EYE-Q check only None
AR-FX7 SOFT SWITCH 7 - 1
Key operator Soft SW No.
SW 28-1 – 4
SW 22-5, 6
SW 64-4 – 8
SW 65-5 – 8
SW 26-1 – 5
SW 25-1 – 4
SW 21-2
SW 51-1 – 2
SW 21-1
SW 14-5 – 8
SW 14-1 – 4
SW 13-5 – 8
SW 13-1 – 4
SW 86-2, 3
SW 87-1 – 7
SW 41-1
SW 7-1 – 8
SW 6-8
SW 15-4 – 8
SW 17-4, 8
SW 43-1
SW43-4 – 6
SW 69-8
SW 42-8
SW 16-1 – 4
SW 73-1
SW 16-5, 6
SW 72-7
Usage
When dialing disable/when error dialing
When dialing disable
When dialing disable in PBX (private branch
exchange/Fax service, etc.)
When dialing disable in PBX (private branch
exchange/Fax service, etc.)
When dialing disable in PBX (private branch
exchange/Fax service, etc.)
When pulse dialing disable
When busy tone detection disable
When busy tone error is detected
When send errors occur frequently
Whey busy occurs frequently
No call-in
No call-in
When an external telephone is connected
When remote switch is erroneously detected
When remote switch is erroneously detected
When the remote machine cannot receive
signals in a proper level.
When an error occurs in the JBIG mode
When SG3 communication error occurs
frequently
When SG3 communication error occurs
frequently
When an error occurs in phase B
Setting is made referring to the distance from
the station when a communication trouble
occurs.
When an error occurs in the SG3
communication.
When an error occurs in the SG3
communication in FAX service, etc.
When an error occurs in the V29
communication
To specified/unspecified destination
When judged as "OK" though RTN is received
When a document of 1m or longer is received
When a lot of errors occur due to the poor
conditions of the line.
When fall-down occurs frequently in the SG3
communication
When an error occurs in phase B in reception
When the line quality is poor and a fall-back
or an error occurs
Change in the detection method of training
error