Sharp MX-FXX1 Service Manual page 27

2) Select a destination button to set the destination. (In this
example, USA/CANADA is selected.) The selected button is
highlighted and the previously selected button returns to the
normal display.
* When the destination button is changed, the new destination
setting is saved to EEPROM of the FAX BOX.
* When, however, there is no destination setting in EERPOM
of the FAX BOX, "NO DESTINATION" is displayed on the
title line and all the destination buttons are normally dis-
played.
<Destination setting table>
JAPAN U.S.A/CANADA
CHINA ASIA&OTHERS
SIMULATION NO.66-39
TEST
FAX DESTINATION SETUP
U.S,A/CANADA
JAPAN
CHINA ASIA&OTHERS
66-42
Purpose : Setting
Function (Purpose) : Used to rewrite the program to power con-
trol installed in the FAX BOX.
Section : —
Item : —
Operation/Procedure
1) Press [EXECUTE] button.[EXECUTE] button is highlighted
and YES] and [NO] buttons become active.
2) Press [YES] button.
The power control program is rewritten.
* During rewriting the power control program, [EXECUTE] and
[YES] buttons are highlighted.
* When [NO] button or [EXECUTE] button is pressed, [EXE-
CUTE] button returns to the normal display, and [YES] and
[NO] buttons gray out.
3) When rewriting of the power control program is normally com-
pleted, "OK" is displayed and [EXECUTE] button returns to the
normal display, and [YES] and [NO] buttons gray out.
* When rewriting of the power control program is failed, the
error message of "NG"is displayed and [EXECUTE] button
returns to the normal display, and [YES] and [NO] buttons
gray out.
SIMULATION NO.66-42
TEST
POWER CONTROL PROGRAM RELOAD
ARE YOU SURE? YES
EUROPE AUSTRALIA
CLOSE
EUROPE AUSTRALIA
CLOSE
NO EXECUTE
MX-FXX1 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 18
66-43
Purpose : Setting
Function (Purpose) : Used to write the adjustment value into the
power control installed in the FAX BOX.
Section : FAX
Item : Setting
Operation/Procedure
1) When the machine enters Simulation 66-43, the following
screen is displayed. (Default: left upper selected)
* Use [↑] [↓] buttons to select the select item of the power
control adjustment value. Selection is made in Item A to H.
When the selected item is the top (last) item, [↑] [↓] buttons
gray out. (The highlighted section of the set value is
switched and the new value is displayed on the setting
area.)
When [↑] [↓] buttons gray out, they are disabled.
* Enter the power control adjustment value with 10-key and
press [OK] button ([↑] [↓] buttons). The set power control
adjustment value is saved to the primary memory area.
* The set data are saved in the primary memory area. There-
fore, the setting is reflected only when [EXECUTE] button is
pressed to execute.
* For the range of the power control adjustment value and
each value, refer to the table.
2) When [EXECUTE] key is pressed, it is highlighted and writing
to the power control is executed. When writing is normally
completed, "OK" is displayed. When it is failed, "NG" is dis-
played.
3) After completion of writing, [EXECUTE] key returns to the nor-
mal display.
<Set range and default value of each set value>
Item
A CI_LEVEL_JUDGE
B CI_CYCLE_MIN
C CI_CYCLE_MAX
D CI_COUNT
E POFF_LEVEL_JUDGE
F EXHS_LEVEL_JUDGE
G RHS_LEVEL_JUDGE
H SON_TIMEOUT
SIMULATION NO.66-43
TEST
PIC ADJUSTMENT VALUE WRITING.
A : 2
CI_LEVEL_JUDGE
A:
2
B : 10 CI_CYCLE_MIN
C : 110 CI_CYCLE_MAX
2 15
D : 3 CI_COUNT
Set range Default value
2 to 15 2
1 to 254 10
2 to 255 110
2 to 15 3
2 to 15 15
2 to 15 10
2 to 15 2
1 to 127 20
CLOSE
EXECUTE OK