Sharp MX-FXX1 Service Manual page 30

SW Bit
Item
No. No.
7 1 Setting of the time of
the transmission/
reception error sound
2-3 Communication results
sheet print settings (for
ordinary transmission)
<FAX only>
4-5 Setting of the
communication results
sheet printing (at times
of broadcast
transmission)
6-7 Communication results
sheet print setting
(when receiving)
<FAX only>
8 Report output (when
receiving confidential
communications)
<FAX only>
8 1-2 Print document
contents when
transmitting (results
sheet)
<FAX only>
3 Automatic printing of
the record sheet when
memory is full.
4-8 Printing of the
communication record
sheet at a designated
time (hours)
9 1-6 Printing of the
communication record
sheet at a designated
time (minutes)
7 Printing of the
communication record
sheet at a designated
time
8 ECM (valid except
during V.34: reflected
in the V.21 DIS/DCS/
DTC)
SW selection and function
Transmission error sound sounding interval
"0": Every 0.3 seconds
"1": Every 0.7 seconds
Sounding time and paper feeding time are the same.
This sets outputting of the communication results sheet following
transmission (excluding successive broadcast, successive polling and
relay broadcast transmission).
"00": Do not print
"01": Always print
"10": At times of transmission failure
The initial value is reverted to if a value outside of the setting range is
set.
This sets outputting of the communication results sheet at times of
successive broadcast, successive polling and relay broadcast
transmission.
"00": Do not print
"01": Always print
"10": Failed transmission address
The initial value is reverted to if a value outside of the setting range is
set.
This sets outputting of the communication results sheet for when
communications are received (excluding confidential communications).
"00": Do not print
"01": Always print
"10": At times of error
The initial value is reverted to if a value outside of the setting range is
set.
Setting to determine whether or not to output the communication results
sheet (receiving) when confidential communications are received.
"1": Print
"0": Do not print
This only functions when the communication results sheet print setting
(receiving) is set to be outputted.
Setting to determine whether or not to print part of the transmitted
document on the communication results sheet (transmission) when
FAX transmission error occurs.
"00": Do not print
"01": Always print
"10": At times of error
The initial value is reverted to if a value outside of the setting range is
set.
This functions when the communication results sheet print setting
(ordinary transmission) (broadcast transmission) is set to be outputted.
Setting to determine whether or not to automatically output the
communication record sheet when transmitted and received data on the
FAX/Internet FAX communication record sheet reach 200 entries.
"0": No (do not output)
"1": Yes (automatically output)
If the data are not outputted, then new data are written over the
previous data starting from the oldest of the 200 entries.
Trigger printing of 200 entries.
Set the hours part of the designated time (hours and minutes) for
outputting the communication record sheet.
Setting can be made over the range of 0 to 23 (hours) in 1-hour
increments by binary inputting. The initial value of 0 hour is reverted to if
a value outside of the setting range is set.
Set the minutes part of the designated time (hours and minutes) for
outputting the communication record sheet.
Setting can be made over the range of 0 to 59 (minutes) in 1-minute
increments by binary inputting. The initial value of 0 minute is reverted
to if a value outside of the setting range is set.
Setting to determine whether or not to output the communication record
sheet at a designated time.
"1": Output the communication record sheet at a designated time
"0": Do not output the communication record sheet at a designated
time. Even if designated time printing is set, do not output when the
designated time coincides with the nighttime FAX mode.
Setting to determine whether or not to execute the error re-send mode.
However, this is only valid when communication is other than V.34.
"1": No. Set with no ECM function.
"0": Yes. Set with ECM function.
ECM is on during communication in the V.34 mode.
MX-FXX1 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 21
Initial value
0 Every 0.3 seconds FAX initial
setting
1 At times of transmission FAX initial
failure setting
0
0 Always print FAX initial
setting
1
0 Do not print FAX initial
setting
0
0 Print FAX initial
setting
1 At times of error FAX initial
setting
0
0 No FAX initial
setting
0 0 hour FAX initial
setting
0
0
0
0
0 0 minute FAX initial
setting
0
0
0
0
0
0 Do not output FAX initial
setting
0 Yes FAX initial
setting
System
settings