Sharp MX-FXX1 Service Manual page 19

Check memory item
5 MFP FLASH + OP.FLASH (Repeat)
6 MODEM EEPROM <1> (Once)
7 MODEM EEPROM <1> (Repeat)
8 MODEM SDRAM <1> (Once)
9 MODEM SDRAM<1>(Repeat)
The number in < > indicates the line.
SIMULATION NO.66-03
TEST
FAX PWB MEMORY CHECK
All Memory Device Check (once)
MFP SRAM (repeat)
MFP FLASH + OP.FLASH (repeat)
MODEM EEPROM<1> (repeat)
66-4
Purpose : Operation test/Check
Function (Purpose) : Used to send the selected signals to the
line and the main unit speaker. (Send level:
max.)
Section : FAX
Item : Operation
Operation/Procedure
1) When the machine enters Simulation 66-04, the screen on the
right is displayed. (Default, left upper selected.)
* Use [↑] [↓] buttons to switch the send mode select page.
When the selected item is the top (last)item, [↑] [↓] buttons
gray out. (The highlighted section of the set value is
switched and displayed on the set setting area.)
When [↑] [↓] buttons gray out, they are disabled.
2) When a button of a signal to be sent is selected, it is high-
lighted and the previously set button is shifted to the normal
display.
* Only one signal to be sent can be selected.
3) When [EXECUTE] button is pressed, it is highlighted and sig-
nals are sent.
4) To end signal send:
When [EXECUTE] button is pressed, it is highlighted and sig-
nal send is interrupted.
<Signal send table>
Page1
NOSIGNAL 33.6 V34
26.4 V34 24.0 V34
16.8 V34 14.4 V34
7.2 V34 4.8 V34
Page2
12.0 V33 14.4 V17
7.2 V17 9.6 V29
2.4 V27t 0.3 FLG
0.3 V21 ANSam
Page3
DP MAKE DP BRK
SIMULATION NO.66-04
TEST
SIGNAL OUTPUT CHECK. (LEVEL MAX)
NOSIGNAL 33.6 V34
26.4 V34 24.0 V34
16.8 V34 14.4 V34
7.2 V34 4.8 V34
Remark
Repeat check
Check only once in LINE1
Repeat check in LINE1
Check only once in LINE1
Repeat check in LINE1
CLOSE
MFP SRAM (once)
MFP FLASH + OP.FLASH (once)
MODEM EEPROM<1> (once)
MODEM SDRAM<1> (once)
31.2 V34 28.8 V34
21.6 V34 19.2 V34
12.0 V34 9.6 V34
2.4 V34 14.4 V33
12.0 V17 9.6 V17
7.2 V29 4.8 V27t
CED 2100 CNG 1100
RINGER No RBT
NO MSG
CLOSE
31.2 V34 28.8 V34
21.6 V34 19.2 V34
12.0 V34 9.6 V34
2.4 V34
14.4 V33
EXECUTE
MX-FXX1 SIMULATIONS, FAX SOFTWARE SWITCH 5 – 10
66-5
Purpose : Operation test/Check
Function (Purpose) : Used to send the selected signal to the line
and the main unit speaker. (Send level: Soft
SW setting) (For the kinds of send signals,
refer to PART1 and PART2 of SIM66-04.)
Section : FAX
Item : Operation
Operation/Procedure
1) When the machine enters Simulation 66-05, the following
screen is displayed. (Default, left upper selected)
* Use [↑] [↓] buttons to switch the send mode select page.
When the selected item is the top (last)item, [↑] [↓] buttons
gray out. (The highlighted section of the set value is
switched and displayed on the set setting area.)
When [↑] [↓] buttons gray out, they are disabled.
2) When a button of a signal to be sent is selected, it is high-
lighted and the previously set button is shifted to the normal
display.
* Only one signal to be sent can be selected.
3) When [EXECUTE] button is pressed, it is highlighted and sig-
nals are sent.
4) To end signal send:
* When [EXECUTE] button is pressed, it is highlighted and
signal send is interrupted.
SIMULATION NO.66-05
TEST
SIGNAL OUTPUT CHECK. (SOFT SW)
NOSIGNAL 33.6 V34
26.4 V34 24.0 V34
16.8 V34 14.4 V34
7.2 V34 4.8 V34
66-6
Purpose : Data output/Check
Function (Purpose) : Used to print the confidential registration
check table (BOX NO., BOX name, pass-
code. (If there is no confidential registra-
tion, no print is made.)
Section : FAX
Item : Data (Confidential passcode)
Operation/Procedure
1) When [EXECUTE] button is pressed, it is highlighted and the
confidential checkable is printed.
* If there is no confidential registration, no print is made even
though [EXECUTE] key is pressed.
2) After completion of printing, [EXECUTE] button returns to the
normal display.
* When [C], [CA], [SYSTEM SETTINGS], or [EXECUTE] key is
pressed during printing, the operation is interrupted.
CLOSE
31.2 V34 28.8 V34
19.2 V34
21.6 V34
12.0 V34 9.6 V34
2.4 V34
14.4 V33
EXECUTE