Lighting And Shutdown Procedures - kozy heat Lakefield 56150 Installation And Operation Manual

LIGHTING & SHUTDOWN
NOTE: Prior to lighting, check all fittings for leakage. This is accomplished by applying soapy water on all connections made. If there is any leakage,
bubbles will appear at the point of connection. If bubbles occur, tighten the fittings until the bubbles no longer appear.
NOTE: The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test
pressures in excess of ½ psi.
NOTE: The appliance must be isolated from the gas supply piping system by closing its individual manual shut off valve during any pressure testing of the gas
line at test pressures equal to or less than 1/2 psig (3.5 kPa).
Pressure check taps for the manifold (outgoing) and inlet (incoming) pressures are located in front of the gas valve. The left pressure tap is the manifold pressure
and the right pressure tap is the incoming pressure. Follow instructions on page 18 for checking these pressures.
NOTE: Read 1-8 before lighting the unit for the first time. Refer to figures below.
1. Access the gas valve by lifting up the „Kozy Heat‟ cover. Push the cover „in‟ slightly and it will stay in position.
2. Set the thermostat, if used, to the lowest setting.
3. Turn off all electric power to the appliance.
4. Push in control knob (A) slightly and turn clockwise
NOTE: Knob cannot be turned from "PILOT" to "OFF" unless knob is pushed in slightly. Do not force.
5. Wait five (5) minutes to clear out any gas. If you then smell gas, STOP! Follow the safety information on front cover of this installation manual. If you don't
smell gas, go to the next step.
6. Find the pilot - follow metal tube from gas control. The pilot is behind the burner tube.
7. Push the control knob on the gas valve „in‟ slightly and turn counterclockwise
8. Push in the black control knob all the way and hold in. Press the igniter button (B). The pilot will generally light with two or three pushes on the igniter.
Hold the knob in for about one (1) minute after the pilot is lit. Release knob and it will pop back out. Pilot should remain lit. If it goes out, repeat steps 4
through 8.
* If knob does not pop out when released, stop and immediately call your service technician or gas supplier.
* If the pilot will not stay lit after several tries, turn the gas control knob to "OFF" and call your service technician or gas supplier.
9. Push the control knob on the gas valve „in‟ slightly and turn counterclockwise
10.
Turn the burner „ON‟ by depressing the on/off switch (C) located on the lower right side of the fireplace to the "ON" position or by setting the thermostat, if
used, to desired setting. IMPORTANT: The on/off switch must be in the "OFF" position for proper thermostat, remote control, or wall switch operation.
NOTE: When the unit is initially lit, condensation will appear on the glass. This is normal in all gas fireplaces and will disappear in one to three minutes.
11. If you wish to turn the burner „OFF‟, depress the on/off switch. If a wall switch has been installed, simply turn it off. If a thermostat has been installed,
simply adjust temperature setting. NOTE: The pilot will stay lit.
12. To turn off the pilot, push the control knob in and turn to the "OFF" position. DO NOT FORCE.
AN ODOR WILL OCCUR DURING THE FIRST FEW HOURS OF BURNING. THIS IS THE PAINT CURING AND SUBSTANCES USED IN THE MANUFACTUR-
ING PROCESS. IT IS RECOMMENDED TO LEAVE THE FAN (IF INSTALLED) OFF DURING THIS PERIOD AS THIS WILL SPEED UP THE PAINT CURING
PROCESS.**MAKE SURE THE HOMEOWNER IS AWARE OF THIS**
THIS FIREPLACE MAY PRODUCE NOISES AS IT HEATS AND COOLS DUE TO METAL EXPANSION AND CONTRACTION. THIS IS NORMAL AND DOES NOT AFFECT THE
PERFORMANCE OR LONGEVITY OF THE FIREPLACE.
NOTE: Children and adults should be alerted to the hazards of high surface temperature and should stay away to avoid burns or clothing ignition. Young children should
be carefully supervised when they are in
Clothing or other flammable material should not be placed on or near the appliance.
IMPORTANT: TEST ALL CONNECTIONS WHETHER FIELD OR FACTORY MADE.
↘
to the "OFF" position.
INITIAL BURN PERIOD
the same room as the appliance.
↙
to "PILOT".
↙
to the "ON" position.
A B
PAGE 17