Sartorius CH1NE Operating Instructions Manual page 92

Data Interfaces
Classification Application
The "Initialization data" block contains
the upper limits of Classes 1 through 4.
The "Results" block contains gross, net
and tare weights, as well as the class
that the sample belongs to (1 through
5, where Class 5 means that the upper
limit of Class 4 was exceeded).
--------------------
Lim1 + 10.000 kg
Lim2 + 11.000 kg
Lim3 + 12.000 kg
Lim4 + 13.000 kg
G# + 9.700 kg
T + 0.000 kg
N + 9.700 kg
Class
--------------------
Animal Weighing Application
The "Initialization data" block contains
the number of measured values that
averaging is based on. The "Results"
block contains the tare weight and
the mean value.
--------------------
mDef 8
T + 0.000 kg
x-Net + 4.202 kg
--------------------
Net-Total Formulation Application
The "Initialization data" block is empty.
If this block is enabled for the printout,
a blank line is output.
Which data is contained in the "Results"
block value depends on the program
operating status at the time of printing.
The following options are available:
– Total/results printout
After c is pressed
(tare memory is cleared)
– Individual/components printout
After O is pressed
(component is stored in tare memory)
– Standard
After p is pressed (component
is not stored in tare memory)
92
"Total" printout:
--------------------
n
S-Comp+
Cont.T+
--------------------
Component printout (menu item 3.17.3)
When the components printout is con-
figured, the header is printed only once,
followed by all components.
If you are using a label printer, make
sure a single label is large enough for
the list of all components. For printer
models YDP01IS and YDP04IS, you
can configure manual form feed in the
operating menu. If the corresponding
setting is active, you can activate "form
feed" manually. With the YDP02IS
1
printer, form feed is automatic after
each print command (fixed setting).
Example with 2 components
HEADER LINE 1
HEADER LINE 2
14.01.2002
--------------------
Cmp001+
Cmp002+
Component printout
(menu item 3.17.2)
The entire standard printout is
generated for each component.
Example for the second component:
HEADER LINE 1
HEADER LINE 2
14.01.2002
--------------------
Cmp002+
Standard printout
Example before the 2nd component
is stored:
G#
T
T2
N
3
3.400 kg
0.200 kg
09:43
1.200 kg
2.000 kg
09:46
2.000 kg
+ 4.400 kg
+ 0.200 kg
+ 4.200 kg
+ 0.000 kg
Totalizing Application
The "Initialization data" block is empty.
If this block is enabled for the printout,
a blank line is output.
Which data is contained in the "Results"
block value depends on the program
operating status at the time of printing.
The following options are available:
– Printout of results
After c is pressed
(totalizing memory is cleared)
– Individual/component printout
of one transaction
After O is pressed
(component is stored in tare memory)
– Standard printout
After p is pressed (component is
not stored in tare memory)
"Total" printout:
--------------------
*G 9.200 kg
*N + 8.600 kg
n 3
--------------------
Component printout (menu item 3.17.3)
The header is printed only once, all
transaction are printed one after the
other. For printing on a label printer,
see also "Component printout, Net-
Total."
Example with 2 transactions:
HEADER LINE 1
HEADER LINE 2
14.01.2002 09:43
--------------------
G# + 1.400 kg
T + 0.200 kg
N + 1.200 kg
n 1
G# + 3.400 kg
T + 0.200 kg
N + 3.200 kg
n 2