Canon iPF9000S Troubleshooting Manual page 163

(2)
(1)
PARTS CNT.
PARTS CR1 : OK 244 278173
PARTS CR2 : OK 244
PARTS CR3 : OK 244 119394
PARTS CR4 : OK 244
PARTS CR5 : OK 244 119394
PARTS SP1 : OK 244
PARTS PG1 : OK 244
PARTS HMa1: OK
PARTS MT1 : OK 244
PARTS PL1 : OK 244
PARTS Mi1 : OK 244
PARTS CT1 : OK 244
PARTS WF1 : OK 244
PARTS WF2 : OK 244
COGFF
CONDITION : 1
PARAM0-F : REF:
.
AMP:
PARAM0-B : REF:
AMP:
LF/SCALE ADJUSTMENT VALUE (MEDIA: Plain Paper
LF-A
ROLL LARGE: -28.3421 MIDDLE: -24.3421 SMALL: -20.3421 SMALLER: -20.3421
CUT LARGE: -36.3421 MIDDLE: -36.3421 SMALL: -36.3421 SMALLER: -36.3421
LF-B
ROLL LARGE: -28.3421 MIDDLE: -24.3421 SMALL: -20.3421 SMALLER: -20.3421
CUT LARGE: -36.3421 MIDDLE: -36.3421 SMALL: -36.3421 SMALLER: -36.3421
SCALE-A
ROLL LARGE: -26 MIDDLE: -22 SMALL: -19 SMALLER: -19
CUT LARGE: -34 MIDDLE: -34 SMALL: -34 SMALLER: -34
SCALE-B
ROLL LARGE: -26 MIDDLE: -22 SMALL: -19 SMALLER: -19
CUT LARGE: -34 MIDDLE: -34 SMALL: -34 SMALLER: -34
PV AUTO JUDGE : ON(NORMAL) , 1
(3) (4)
12476190 2%
83773 6700000 1%
16500000 0%
1084 60000 1%
16500000 0%
83773 4400000 1%
922 50000 1%
244 0.0 29.8
21 15000
4 778
0.1 37.0
896 100000
0.0 169.0
0.3 45.0
(1) Status (OK, W1, W2, E)
(2) Number of days passed after set (days)
(3) Count value
(4) Life threshold (W2/E)
(5) Usage (ratio of life value to count value)
(6) Cumulative count
5740 52477 0
0 40 0
3245 54033 0
0 49 0
(5) (6)
278173
83773
119394
1084
119394
83773
922
0% 0.0
0% 21
0% 4
0% 0.1
0% 896
0% 0.0
0% 0.3
0 PHASE: 0 176
0 RATE: 0 69
0 PHASE: 0 301
0 RATE: 0 79
)
Ink reduction mode
On (Display Normal/Low when On only)/Off
Entry to ink reduction mode count
5-9
Chapter 6 Miscellaneous Information
Parts counter
CR1: CR bushing
(CR scan distance unit: 210mm)
CR2: Long flexible cable CR scan count)
CR3: Encoder sensor unit
(Dot count unit:1,000,000 dots)
CR4: Head height switch cam
Rotation count of head height switch
cam
CR5: Multisensor unit
(Dot count unit:1,000,000 dots)
SP1: Ink tube unit (CR scan count)
PG1: Purge unit
(Rotation count of the controller cam)
HMa1: Head management sensor
(Non-ejection dot count ml)
MT1: CR motor (CR driving time h)
PL1: LF adjustment (Paper feeding time h)
Mi1: Mist fan unit (Dot count ml)
CT1: Cutter (Cut count)
WF1: Lower ink absorber of MTC (Dot count
Cogging adjustment
Result: (0: DIsabled/1:Enabled/2. Check
required /3: Adjust required) and value when
adjusting.
0 0
0 0
0 0
0 0
LF adjustment value (User adjustment
value
LF-A:Band adjustment 8-pass
LF-B: Band adjustment 1-pass
Scale-A: Scale clean
Scale-B: Scale fast