Arming And Disarming The System - Gemini GEM-P9600 User Manual

WI742D 5/03
not only through numbers 0-9, but through the alphabet and a series of punctuation marks and symbols as well. (Roughly note
the order in which the letters, numbers and symbols are displayed so that you will be able to determine the proper direction to
scroll, up or down, for fastest access. As familiarity improves, so will programming speed). When the description has been en-
tered and is satisfactory as displayed (e.g. "GARAGE"), you MUST press the
To advance to the next zone (or to any other zone, for that matter), position the cursor over the displayed Zone Number, i.
e., "01" using buttons
1
description programming procedure for the new zone. Advance to the next zone and repeat until all zones (up to 96 zones)
have been programmed.

ARMING AND DISARMING THE SYSTEM

In the normal disarmed state, only the green STATUS LED will be on and the display will read "SYSTEM READY". To silence
an alarm, enter any User Code, then press the
Only Code may only be used to arm.
Arming
!
To arm, enter a valid User Code, then press the
!
To arm, enter a valid User Code, then press the
(If a wrong code is entered, the keypad will display "INVALID ENTRY / TRY AGAIN"). The green STATUS LED will go off,
the red ARMED LED will go on, and the display will read "PLEASE EXIT IN / XXX SECONDS" ("XXX" representing the pro-
grammed exit-delay time, in seconds). The exit delay will immediately start counting down toward "000", in 10-second decre-
ments, indicating the available time remaining to exit through an exit/entry door.
1. If Exit Delay Restart is enabled, after the panel is armed and the exit door is opened and then closed, exit delay will
restart at 60 seconds. If re-entry occurs within this 60-second interval, the alarm device will sound a 2-second warning
"chirp", if programmed, as an entry reminder to the user to return to the keypad and disarm.
2. (GEM-RP1CAe2/GEM-K1CA keypads only). An "S" in the display (e.g. "EXIT TIME XXX S") will appear as a re-
minder that the system is being armed with the Service Code active. (To turn off the Service Code, disarm, then rearm
using a regular Arm/Disarm Code).
3. If a System Trouble is displayed, there should be an attempt to correct the system trouble (for example by calling an
alarm maintenance or an alarm repairman). If this cannot be done, then press the
access the keypad without the system trouble display. Immediate attention should be provided, when system troubles
are encountered.
4. In commercial applications, if Start Exit Delay After Ringback is programmed, exit delay will not start until the central
station acknowledges receipt by a ringback tone at the keypad. The display will read "PLEASE WAIT" while the control
panel communicates to the central station. If the ringback tone does not sound within about 30 seconds, the START
EXIT TIME function may be used to manually start exit delay.
Disarming
When the exit time has elapsed, the display will read "SYSTEM ARMED". This indicates that upon entering the premises
through an exit/entry door, there will be an entry delay to allow time to disarm the panel. The GEM-RP1CAe2 or GEM-K1CA
display will read "DISARM NOW / XXX SECONDS" ("XXX" representing the programmed entry-delay time, in seconds). The sounder will
come on and the entry delay will immediately start counting down toward "000" in intervals of 10 seconds, indicating the avail-
able time remaining to disarm the panel. (Note: The sounder will "pulse" with the GEM-P9600/3200 version 30 and above,
and with the GEM-P1632/816 version 10 and above. The sounder will sound a "steady" tone with the GEM-P9600/3200 ver-
sion 20 and lower, and with the GEM-P1632/816 version 9A and lower). The sounder will emit a rapid pulsing warning tone
during the final 10 seconds.
To disarm the panel, enter a valid User Code, then press the
Arming in AWAY MODE
AWAY MODE provides for full protection of the perimeter and interior zones. Exit/Entry doors are provided with Exit/Entry
delays. A "Classic" (non "K Series") keypad will display "SYSTEM ARMED", while a "K Series" keypad will display "ARMED
AWAY." The RED LED will remain ON. With "K Series" keypads such as the GEM-K1CA and the GEM-K2AS, press
to begin the exit delay process (the exit delay will immediately start counting down toward "000", in 10-second decrements, in-
dicating the available time remaining to exit through an exit/entry door).
L
NAPCO Security Systems
and . Change the Zone Number using buttons
2
U D
or button. Any valid User Code may be used to arm or disarm; an Arm-
U D
or
D
button. (For all "Classic GEM-RP keypads)
button. (For all "K Series" keypads)
Q
U D
or button.
X
GEM-P9600 Installation Instructions
button to save it in memory.
and . Repeat the zone-
3 6
button to allow 5 minutes to
C
!
Page 23
Q