Integra DTR-5.3 Instruction Manual page 20

Connections (DTR-6.3)
Video output
S Video output
Video input
S Video input
7. DVD recorder, other digital
video recording device
(VIDEO 2)
Analog audio input
Analog audio output
7. Connecting a DVD recorder or other digital video recording
device (VIDEO 2)
Using RCA video cables, connect the video output jack (composite)
of the device to the VIDEO 2 VIDEO IN jack of the DTR-6.3 and
connect the video input jack of the device to the VIDEO 2 VIDEO
OUT jack of the DTR-6.3. Or if the device has S video input and
output jacks, using S video cables, connect the S video output jack of
the device to the VIDEO 2 S VIDEO IN jack of the DTR-6.3 and
connect the video input jack of the device to the VIDEO 2 S VIDEO
OUT jack of the DTR-6.3. Or if the device has component video
outputs, connect them to the COMPONENT VIDEO INPUT 1 or 2
jacks on the DTR-6.3.
With the initial settings of the DTR-6.3, the VIDEO 2 input
source is set for the COMPONENT VIDEO INPUT 2 jacks.
If you connect the device to the COMPONENT VIDEO INPUT 1
jacks, this must be changed at "Input Setup" → "Component Video"
(see page 53).
Using RCA audio cables, connect the audio output jacks of the
device to the VIDEO 2 IN audio jacks of the DTR-6.3 and connect
the audio input jacks of the device to the VIDEO 2 OUT audio jacks
of the DTR-6.3. Make sure that you properly connect the left
channels to the L jacks and the right channels to the R jacks.
If the device has a digital output, connect it to either the DIGITAL
INPUT COAXIAL jack or the DIGITAL INPUT OPTICAL jack of
the DTR-6.3 depending on the type of connector on the device.
With the initial settings of the DTR-6.3, nothing is allocated as
the digital input source for VIDEO 2 (----).
If you connect the digital audio output, be sure to make the appropriate
changes at "Input Setup" → "Digital Input" (see page 53).
If the device has a digital input, connect it to the DIGITAL OUTPUT
(OPTICAL or COAXIAL) jack of the DTR-6.3 for digital recording
of the signal from the digital input of the DTR-6.3.
Note:
The output from the DIGITAL OUTPUT jack of the DTR-6.3 is only
the digital signal input to the DIGITAL INPUT jack.
20
FM 75
ANTENNA
12 V
TRIGGER
IR OUT
OUT
56K
A
B
ZONE 2
DIGITAL INPUT
OPTICAL
2 1
IN
L
SUBWOOFER
PRE OUT
R
CD
L (white)
R (red)
L (white)
R (red)
PHONO IN
AM
R L GND
COMPONENT VIDEO
INPUT 2 INPUT 1
RS232
ZONE 2
LINE OUT
40K ZONE 2 DC IN
OUT 24V 1A
A
L
B
R
DIGITAL VIDEO 3 VIDEO 2 VIDEO 1 DVD
COAXIAL
OUTPUT IN OUT IN OUT IN IN
OPTICAL
COAXIAL
DIGITAL
INPUT
OUT IN IN OUT IN OUT IN FRONT
TAPE VIDEO 3 VIDEO 2 VIDEO 1
8. Connecting a television monitor or projector (MONITOR
OUT)
The DTR-6.3 is equipped with a simple Y/C separate circuit and
simple Y/C mixed circuit. Since both the signal from the S VIDEO
and VIDEO inputs are output to the MONITOR OUT S VIDEO
output, if the television or projector is equipped with an S video
input, it is unnecessary to connect the video connectors. If it is
equipped with only a video input, connect it to the MONITOR OUT
VIDEO output.
Using an RCA video cable, connect the video input jack (composite)
of the device to the MONITOR OUT VIDEO jack of the DTR-6.3.
Or if the device has an S video input jack, connect it to the
MONITOR OUT S VIDEO jack of the DTR-6.3 using an S video
cable. Or if the device has component video inputs, connect them to
the bank of COMPONENT VIDEO OUTPUT jacks on the DTR-6.3.
Note:
Note that the Setup Menu will only be displayed on the monitor
connected to MONITOR OUT and not those connected to the
COMPONENT VIDEO OUTPUT jacks.
8. TV monitor or projector
(MONITOR OUT)
OUTPUT
Y
Y
P
B
P
B
REMOT
P
CONTRO
R
P
R
MONITOR
IR
OUT
OU
V
I
S
SURR CENTER
L
R
SUB
WOOFER
DVD
Component video
input
Video input
S Video input
: Signal flow